Rebluum RB-3PT1 Security Camera Wireless Outdoor User Guide
- June 14, 2024
- Rebluum
Table of Contents
Solar Battery
-Wireless Security Camera GEEERIH
Quick Start Guide
What’s Included
Product overview
CAUTION: Please insert the Micro SD Card according to the direction shown
in the diagram. Micro SD Card might JAM if inserted incorrectly and device
could be damaged.
SD Card Port : Support micro SD card for local storage (Max 128GB).
Reset button: Used to restore the camera to factory settings (Press and
hold on 5-85).
Card capacity requirements: 8-128GB.
Read and write speed requirements: class10 level.
File format: FAT32.
CloudEdge App installation and Setup
Search ” CloudEdge” on apple store or google play to download the app.
- from Google Play
- from Apple Store
- or Scan the following QR code
|
---|---
https://itunes.apple.com/app/id1294635090?mt=8|
https://play.google.com/store/apps/details?id=com.cloudedge.smarteye
Download App(I10S & android)
Mounting the camera
Select Height and location
Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes the
detection range of the motion sensor of the camera. Avoid placing the camera
under direct sunlight.
Installation
- Drilling according to position sticker, drill bit: 15/64°(6 mm).
- Insert the plugs.
- Tighten the screw.
What is required:
Installation instruction of solar panel
- keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
- The installation between the solar panel and the camera is shown in the following figure(open up the silicone cover at the bottom of the camera, remove the small center part of the cover, insert the power cord through the opening and plug it into the Type C port and then close the cover taking up any slack in the power cord from the solar panel).
Tips for the installation of solar panel
- When installing in the northern hemisphere, face the panel to the south, and when installing in the southern hemisphere, face the panel to the north.
- Take care to install the solar panel so that the sun is not blocked by any items such as eaves, trees branches, etc.
Test the Wifi signal at installation position
Use cell phone to test Wifi signal quality at the installation position before installing camera, make sure the Wifi router can provide good Wifi signal.
Register an account
The CloudEdge app that is necessary to operate the camera.
Signing up for storage in the cloud is totally optional and is really not
necessary when using an onboard Micro D card.
- Open the APP to sign up an account. Go to the login interface, and click “Sign Up’.
- Sign up with your email address, and click “Next’.
- Set up an “Nickname” and “Password” for your APP, click “Done” to complete.
Set up WiFi for The camera
-
Bring both your mobile phone and your camera close to your router (max distance of 5 meters/16 feet).
Note: The camera can only connect to a 2.4 GHz Wifi signal. It does not support using a 5 GHz signal.
Therefore, please ensure you connect to a 2.4 GHz signal on your network as shown in the below illustration.
-
Login to “CloudEdge”, then tap the “+” icon in the center. Tap “Battery Camera” to add device.
-
Reset the device and wait for a flashing RED indicator light, then tap “Next”.
-
Selecting the Wi-Fi the device needs to connected with (your home Wi-Fi), input the password and click “Next”.
-
Use the camera to scan the QR code on your mobile phone as noted below.
When the scan is complete you will hear a prompt tone then push Next.
-
After the network configuration is successful, set the name and password for the device to add successfully, then you can view the camera screen in real time
Humanoid Detection
Turn on humanoid detection, the alert will be triggered only when human motion is detected. Click the Settings button ****and select “Alarm Management” then enable “Motion Detection “and click “Alarm Working Mode”, select “Custom Mode “and click the Settings button to set the humanoid alarm. Recording Time: The duration of each alarm video; Alarm Interval: Interval of each alarm push.
Tips: If you want to detect other moving objects such as vehicles, please turn off humanoid detection switch. don’t urn on “Day Detection” and “Night Detection”.
Audio warning and strobe light
Audio warning and strobe light is only valid at night.
Device Share
The camera can only be added by one APP account. If other family members want to view the camera, you can share the camera with your family through the sharing function of the APP. Click the Settings button and select “Device Share”—”Add”—” Enter account” and input other party’s APP account, then your family will receive a shared message on the APP, click Agree to view the camera you shared.
FAQ
Q: The device prompts offine?
A: • Check whether the equipmentisin the power-on state. • Check whether the Wi-Fine work is in good condition and restart the router. • If the device is located far away from the router, which results in the inability to obtain a good Wi-Fisignal, it is recommended to move the router to a closer place or add a Wi-Fi amplifier to improve the Wi-Fi performance of the home. • Delete the camera from your CloudEdge Appaccountand add it again after resetting the device. • Check whether the device firmware and application program are the latest version.
Q: Why is it still in the list of devices after reseting?
A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.
Q: How to cut the camera network to another router?
A: First remove and reset the device on the App and then configure the device again by the App.
Q: Why doesn't the device identify the SD card?
A: Itis recommended to plug in SD card after power cut. Confirm whether the SD card is normally available and the format is FAT32. And the TF card can't be identified when the internet environment is not good.
Q: Why | can't get the notifications with my cell phone App?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.
Satety Statement
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/ TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in fixed/mobile exposure condition. The min separation
distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Warranty Tips
Please fill in the following information or scan QR code to activate the free
12-month warranty from the order date on.
After finish filling or scanning, please take a picture and send it to the
email(support@szrebluum.com).
Then your free warranty will take effect!
During the warranty period, if any parts of product are damaged, please
contact us immediately and we will provide satisfactory resolution.
Order Date:…………………
Order Number/ID:…………………
Buyer E-mail:…………………
Buyer Tel:…………………
Contact us
support@szrebluum.com
+1 844 497 1656
Youtube: Rebluum Security
http://service.viziuuy.com/prize
Documents / Resources
|
Rebluum RB-3PT1 Security Camera Wireless
Outdoor
[pdf] User Guide
RB-3PT1 Security Camera Wireless Outdoor, RB-3PT1, Security Camera Wireless
Outdoor, Camera Wireless Outdoor, Wireless Outdoor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>