EnviroLite RC7WHWH8102C DF Recessed Light Trims Instruction Manual

EnviroLite RC7WHWH8102C DF Recessed Light Trims

Product Information

The 2CCT Disk Light Fixture is a versatile lighting solution that can be installed as a flush mount LED fixture on an outlet box suitable for wet locations. It is designed for use with 6-inch recessed cans or standard 4-inch electrical boxes. The fixture comes with a lens, socket adapter, and various mounting screws.

Important Safety Warning:
Before installing or servicing the fixture, make sure to disconnect the main power at the fuse or circuit breaker to avoid the risk of electric shock. All electrical connections must comply with local and National Electrical Code (N.E.C.) standards. If you are unsure about proper electrical wiring connections, it is recommended to seek the assistance of a qualified electrician.

Compatible Dimmers:
For dimming capabilities, refer to the list of compatible dimmers available at www.envirolite-LED.com. Look up the item number for a complete list.

FCC Notice:

• FCC responsible party: Cordelia Lighting
• Address: 20101 S Santa Fe Avenue, East Rancho Dominguez, CA 90221

Light Distribution Map:

• -/+180 | -150 | 150
• -120 | 120

Product Usage Instructions

Can Housing Installation:

1. Remove the lens from the fixture pan by rotating it counterclockwise.
2. Adjust the color temperature by moving the CCT switch on the LED board to the desired setting.
3. Thread the socket adapter into the socket.
4. Plug the female connector on the fixture into the male connector on the housing.
5. Squeeze both torsion spring arms together and insert them into the torsion spring slots (or receiver brackets) of the can.
6. Tuck all wires into the can and carefully push the fixture into the can, ensuring it is securely flush against the ceiling surface.
7. Position the lens onto the fixture pan and turn it clockwise to secure it.

Junction Box Installation:

1. Remove the lens from the fixture pan by rotating it counterclockwise.
2. Adjust the color temperature by moving the switch on the fixture to the desired setting.
3. Pull the supply wires out from the outlet box and thread the mounting screws into the outlet box.
4. Using wire cutters, remove the female connector from the fixture supply wires.
5. Connect the black supply wire to the black fixture wire using a wire connector. Connect the white supply wire to the white fixture wire using a wire connector. Connect the fixture ground wire to the supply ground wire using a wire connector.
6. Carefully tuck all wiring into the outlet box. Align the fixture pan over the outlet box, position the mounting screws through the large openings of the keyhole slots, and rotate the fixture pan to seat the screws securely.
7. Position the lens onto the fixture pan and turn it clockwise to secure it.

Please read carefully and save these instructions as you may need them at a later date.

WARNING
RISK OF ELECTRIC SHOCK. DISCONNECT THE MAIN POWER AT THE FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.

GENERAL:
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician. Remove the flush mount fixture from the box and make sure that no parts are missing by referencing the PARTS illustrations.

WARNING- RISK OF FIRE OR ELECTRIC SHOCK
FOR USE AS A FLUSH MOUNT LED FIXTURE ON AN OUTLET BOX WHICH IS SUITABLE FOR INSTALLING IN WET LOCATIONS.

• Do not alter, relocate, or remove wiring, power supply, or any other electrical component. Installation of the fixture requires a person familiar with the construction and operation of the fixture’s electrical system and the hazards involved. If not qualified, do not attempt installation. Contact a qualified electrician. 2. Move the position of the switch on the fixture to the desired color temperature. (FIG. 1)
• Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.

Parts

Compatible Housing Dimensions

ASSEMBLY AND INSTALLATION

Can Housing Installation

FOR INSTALLATION ONTO 6-INCH RECESSED CANS ONLY.

1. Remove the lens from the fixture pan by rotating the lens counterclockwise.
2. Move the position of the CCT switch on the LED board on the fixture pan to the desired color temperature. (FIG. 1)
3. Thread the socket adapter into the socket. (FIG. 2)
4. Plug the female connector on the fixture into the male connector on the housing. (FIG. 3)
5. Squeeze both torsion spring arms together and insert into the torsion spring slots (or receiver brackets) of the can. (FIG. 4)
6. Tuck all wires into the can and carefully push the fixture into the can. (FIG. 5) Make sure the fixture is securely flush against the ceiling surface.
7. Position the lens onto the fixture pan and turn it clockwise until secure (FIG. 5)

Junction Box Installation
FOR INSTALLATION ONTO STANDARD 4-INCH ELECTRICAL BOXES ONLY.

1. Remove the lens from the fixture pan by rotating the lens counter clockwise.
2. Move the position of the switch on the fixture to the desired color temperature. (FIG. 1)
3. Pull the supply wires out from the outlet box. Thread the mounting screws into the outlet box. (FIG. 6)
4. Using wire cutters, remove the female connector from the fixture supply wires.
5. Connect the black supply wire to the black fixture wire using a wire connector. Connect the white supply wire to the white fixture wire using a wire connector. Connect the fixture ground wire to the supply ground wire using a wire connector. (FIG. 7)
6. Carefully tuck all wiring into the outlet box. Align the fixture pan over the outlet box, and position the mounting screws through the large openings of the key hole slots. Rotate the fixture pan to seat the screws, and tighten securely. (FIG. 8)
7. Position the lens onto the fixture pan and turn it clockwise until secure.

DIMMING
For a complete list of compatible dimmers, please look up the item number at www.envirolite-LED.com.

FCC NOTICE

• FCC responsible party: Cordelia Lighting
• Address: 20101 S Santa Fe Avenue East Rancho Dominguez, CA 90221
• Phone: 800-345-0542

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiver antenna.
2. Increase the separation between the equipment and the receiver.
3. Install the product onto a circuit different from that to which the receiver is connected.
4. Consult with the dealer or an experienced radio/TV technician for help.

CAUTION:
Any changes made to the electronics circuit will void this equipment’s compliance with Part 15 of the FCC Rules and should not be operated.

• Complies with CAN ICES-005 (B) / NMB-005 (B)

LIGHT DISTRIBUTION MAP

FIVE-YEAR LIMITED WARRANTY

EnviroLite© warrants this product to be free from defects in material and workmanship for five years from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt. EnviroLite© will not be liable for loss or damage of any kind, incidental or consequential damages of any kind, whether based on warranty contract or negligence and arising in connection with the sale, use or repair of the product claimed to be defective. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Misuse, accident, improper installation, or maintenance will also void the warranty.

QUESTIONS?

• CALL TOLL FREE 1-855-373-6156

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>