ENFORCER EV-N1806-2W4D IP 8MP Ultra Low-Light Active Deterrence Bullet

Camera

Product Information

Specifications

• Type: Bullet camera
• Sensor: 1/1.8 8MP Sony CMOS
• Video encoding: H.265, H.264, MJPEG
• Megapixels: 8MP
• Resolution: 3840×2160
• Backlight: Disable (Default), Back Light, HLC, WDR
• DNR: 2DNR, 3DNR
• AI Functions:
  • Human and Vehicle Detection
  • Perimeter Intrusion Detection
  • Line Crossing Detection
  • Stationary Object Detection
  • Cross Counting
  • Heat Map
  • Crowd Density Detection
  • Queue Length Detection
  • Face Detection
  • Facial Recognition
  • License Plate Detection
  • License Plate Recognition

• of LEDs: N/A

• Lens Viewing angle: N/A
• Minimum illumination: N/A
• F Stop: N/A
• Gamma correction: N/A
• Gain control: N/A
• White balance: N/A
• Operating voltage: N/A
• Power consumption: N/A
• IP Rating: N/A
• Operating temperature: N/A
• Dimensions: N/A
• Weight: N/A
• On-board storage: N/A

Product Usage Instructions

Installation

1. Use the included mounting template to mark the positions for mounting screws.
2. Attach the camera to the mounting screws using the provided hex key.
3. Connect the camera to power using the weatherproof connector.

Custom Message Upload
To upload a custom message for alarm triggers:

1. Ensure the message is in WAV or PCM format and not exceeding 256KB.
2. Access the camera’s Web Administration manual from www.seco-larm.com for detailed instructions.

Frequently Asked Questions (FAQ)

• Q: How can I access the full Web Administration manual?
  A: You can download the full Web Administration manual from the camera’s product page on www.seco-larm.com.

• Q: What AI functions are supported by the camera?
  A: The camera supports various AI functions including Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, and more. Refer to the manual for the full list.

IP 8MP Ultra-Low-Light
Active Deterrence Bullet Camera

EV-N1806-2W4D Installation Manual

Features

• Active Deterrence – uses light and sound to warn intruders that they are being monitored, providing an extra level of protection
• Upload custom message to play when alarm is triggered (WAV or PCM, up to 256KB)
• 1/1.8″ 8MP Sony CMOS Sensor
• Ultra-low-light technology
• 4K@30FPS, 2160p (3840×2160)
• 2.8mm, F1.0 Lens
• Tri-Stream encoding: H.265, H.264, MJPEG
• True Wide Dynamic Range (WDR)
• Digital Noise Reduction (3DNR)
• Full color
• Corridor mode
• IP67 Weatherproof
• MicroSD slot (512GB max.)
• PoE (IEEE 802.3af), 12VDC
• Operating temperature: -40°~131°F (-40°~55°C)

AI Functions

• Human and Vehicle Detection
• Perimeter Intrusion Detection
• Line Crossing Detection
• Stationary Object Detection
• Cross Counting
• Heat Map
• Crowd Density Detection
• Queue Length Detection
• Face Detection
• Facial Recognition
• License Plate Detection
• License Plate Recognition

For the full Web Administration manual, download from the camera’s product page on www.seco-larm.com.

Parts List

• 1x Camera
• 1x Manual
• 2x Hex key
• 1x Mounting template
• 3x Mounting screws
• 1x Weatherproof connector

Specifications

Detection, Line Crossing Detection, Stationary Object Detection, Cross Counting, Heat Map, Crowd Density Detection, Queue Length Detection, Face Detection, Facial Recognition, License Plate Detection, License Plate Recognition
# of LEDs| 2x Warmlight, 1x red, 1x blue
Lens| 2.8mm
Viewing angle| 132°
Minimum illumination| Color: 0.0005Lux at F1.0 (AGC on) 0Lux with Warmlight on
F Stop| 1.0
Gamma correction| Auto
Gain control| Auto
White balance| Auto
Operating voltage| 12VDC, PoE (IEEE 802.3af Class 0)
Power consumption| <6W
IP Rating| IP67
Operating temperature| -40°~131° F (-40°~55° C)
Dimensions| ø33/4” x91/16” (ø96×230 mm)
Weight| 1-lb 12-oz (800g)
On-board storage| Built-in memory card slot, Supports MicroSD/SDHC/SDXC up to 512GB

Overview

IMPORTANT NOTES

• Do not cut DC jack or RJ45 jack as warranty will be voided.
• Do not open camera case, no serviceable parts.

Before Starting

1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera in areas exposed to radiation, strong magnetic fields, or strong electrical signals.
4. Do not point the camera at the sun. Heat could damage the camera, even when not in use.
5. Do not open or disassemble the camera. There are no field-serviceable parts inside.
6. Do not drop the camera or subject it to strong vibrations.

Installation

1. Run a 12VDC power supply wire and cable with an RJ45 jack through the wall at the location where the camera is to be mounted. The 12VDC power supply wire is not required if using PoE.

2. Install and Execute “Device Config Tool” on a computer connected to the same network as the camera.

3. Press the “Search” button. This will search for IP cameras connected to the same router on the network. It may take several seconds to complete. Default IP address is 192.168.1.168.

4. Once the search is complete, click on the camera IP or type the IP address manually using Internet Explorer.

5. IP Address: The camera may use Dynamic or Static IP addressing. An example of a typical static IP setting is as follows:

   • IP Address: 192.168.0.10 (you can change the last column)
   • Netmask: 255.255.255.0
   • Gateway: 192.168.0.1
   • DNS1/2: You can copy the PC’s network properties. This is for an internet environment.

6. Input “admin” for user ID and password. If this is the user’s first time logging into the camera, the user will be prompted for a new password.
   NOTE: If the password is unknown, hold the RESET button located on the camera for about 10 seconds and reload “Device Config Tool”.

7. In order to access the camera web interface, the user will be prompted to download and install the Active-X web plugin.

8. Once installed, the user will be able to view live camera video and modify necessary configurations.

NOTE: For the full Web Admin manual, download from the camera’s product page on www.seco-larm.com.

Camera Angle and Positioning
To adjust the camera angle and positioning, loosen the camera angle adjustment screw and mounting arm adjustment screw. Rotate the camera and position the mounting arm in the desired position and retighten the screws.

Troubleshooting

The screen is blank

• Check that the camera is powered up.
• Check that the power supply’s polarity is correct.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.

The screen image is dim

• Clean the lens using a soft, clean cloth.
• Check that the light source is adequate.

The screen image has poor contrast

• Adjust the monitor’s contrast knob.
• Change the position of the camera.

The screen image flickers

• Change the position of the camera.

The screen image is distorted

• Change the position of the camera.

The camera case is hot

• Check that the correct power supply is in use.

FCC COMPLIANCE STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.

IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO- LARM will not be held responsible for the use of this product in violation of any current laws or statutes.

IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national, state, and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.

California Proposition 65 Warning: These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

WARRANTY

This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2023 SECO-LARM U.S.A., Inc. All rights reserved.

SECO-LARM ® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606

Website: www.seco-larm.com
Phone: 949-261-2999 | 800-662-0800
Email: sales@seco-larm.com

MI_EV-N1806-2W4D_230926.docx

References

• La Armería de Madrid - fabricantes de armas y rifles
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>