elinchrom EL20616.1 ELC Pro HD 1000 Flash Head User Guide

June 4, 2024
elinchrom

elinchrom logo Elinchrom EL20616.1 ELC Pro HD 1000 Flash Head Quick Start
User Guide
elinchrom EL20616 1 ELC Pro HD 1000 Flash Head
Quick Start Guide

DISPLAY PANEL – DASHBOARD

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - fig 4

  1.  EL-Skyport synchronisation normal/ speed
  2. EL-Skyport Frequency channel
  3. EL-Skyport Group number
  4. Photocell status
  5. Ready beep
  6. Power in J
  7. Flash duration in s
  8. Flash function
  9. Flash function value
  10. Increase I. f-stop (R)
  11. Open flush test (5)
  12. Decrease I. f-stop (L)
  13. Recycling mode
  14. Power in f-stop equivalent

DISPLAY PANEL – MAIN MENU

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - fig 5

  1. Menu title
  2. Menu selected
  3. Menu exit (back to dashboard) (R)
  4. Enter (S)
  5. Back (L)
    elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - fig 3

Added possibility to enable/disable flash before ready.

  • When “ENABLED”, the Strobo mode will work at the fastest possible speeds.
  • When “DISABLED”, flashes can be only released when the charge level is reached. The priority is on accurate exposures.

Activation:
When the unit is OFF, press and hold ON + knob button (S) until the message “ENABLED” is shown, to return to  “DISABLED” repeat the programming procedure,the show value is automatically saved as the standard setting for the unit.

DISPLAY PANEL – MODELING LAMP

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - fig
2

  1.  Setting title
  2. Modelling lamp status
  3. Back to the dashboard (R)
  4. Visual Flash Confirmation function (S)
  5. Proportional modelling lamp setup (L)
  6. Proportional modelling lamp value
  7. Visual Flash Confirmation status
  8. Modelling lamp power in f-stop

KNOB COLOR INFO

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - icon
2 Knob Button (S)

Display Description
Green Ready
Green blinking Discharging
Orange Charging
Red blinking Flashing before 100% ready
Red breathing Stand by

ELINCHROM STUDIO APP / SOFTWARE

Speed up your workflow with the Elinchrom App / Software and take control of your light wherever you are.

  • Control up to 20 units
  • Save and reload presets
  • Edit a friendly name
  • Change group by drag & drop
    Available on macOS, Windows, Android and iOS

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - fig 1elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - qr code
2www.elinchrom.com/range/app- software/

ERROR MANAGEMENT

Error

|

Description

|

Solution

---|---|---


1

| ****

Capacitor over voltage

| Switch the unit off, wait 2 minutes and switch the unit on again. If the error shows up again the unit requires a check-up at an authorized Elinchrom service centre.


2

| ****

Overheat

| Wait until the unit has cooled down. The unit will switch back to normal operation as soon as the temperature decreases to a normal working level.
3| Discharge error| ** Switch the unit off, wait 2 minutes and switch the unit on again. If the error shows up again the unit requires a check-up at an authorized Elinchrom service centre.
4| Charge timeout error
******5

6

| Zero detect fault __

Charge hold error

8| Fan error
10| Supply input voltage too high| ** The unit has detected a main supply fault. Please check the mains/battery supply. It could be not working correctly.
11| Supply input voltage too low
12| Supply under voltage detected until the charge
15| The temperature sensor “Heat Sink” is not connected| ** Switch the unit off, wait 2 minutes and switch the unit on again. If the error shows up again the unit requires a check-up at an authorized Elinchrom service centre.
16| The temperature sensor “Front” is not connected
17| Temperature sensor “Charge” not connected
20| Power Board not connected/found


24

| Capacitor voltage symmetry error| Switch the unit off, wait 10 minutes and switch the unit on again. If the error shows up again the unit requires a check-up at an authorized Elinchrom service centre.


28

| ****

Flash tube afterglow

| Switch the unit off, wait 2 minutes and switch the unit on again. If the error shows up again the unit requires a check-up at an authorized Elinchrom service centre.

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - qr code
1 Download the ELC Pro HD User Guide
www.elinchrom.ch/supportelinchrom EL20616
1 ELC Pro HD 1000 Flash Head - qr code 3 Download the
ELC Pro HD User Guide

** www.elinchrom.com**

elinchrom EL20616 1 ELC Pro HD 1000 Flash Head - icon
3

Elinchrom is a registered trademark of ELINCHROM LTD, RENNES, SWITZERLAND
QSG ELC PRO HD – 73019 – 06.2022
Av. de Longemalle 11, CH-1020 Renens, Switzerland
Tel. : + 41 21 637 26 77 / e-mail: support@elinchrom.ch

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals