elinchrom One Three Off Camera Flash User Guide
- June 14, 2024
- elinchrom
Table of Contents
elinchrom One Three Off Camera Flash
Setup Menu
Action mode
Switch on/off
Settings
Submenu access
Sound
Switch on/off
Photocell
Switch on/off
Settings
| Flash before ready| Yes/No
---|---|---
Flash scale| EL-Scale, 10 F-stop scale, Ws
Modlamp VFC| Off/On
Modlamp Timer| Off/15”/30”/60”
Mod lamp Scale| F-stop/Percent
Favorite function| Mod lamp/Flash mode/Audio/ Photocell/Recycling
mode
Auto stand-by| Off, 1 to 59 min. Auto-off and auto stand-by shall
be set independently. Auto stand-by cannot disable auto off.
Auto-off| Off, (Auto stand-by+1) to 60 min.
It shall be longer than Auto stand-by. Minimum value = auto stand-by +
1min.
EL logo mode| Low, High, Off, Low on ready, High on ready
EL logo color| Group color, White
Ready tone| 1, 2, 3
Ready volume| Off, Low, Medium, High
Keyboard click| Off/On
Sky port| Off/On
Touch| Off/On
Wireless update| Setup wifi SSID and password
To access the menu short top on screen with 2 fingers
Groups
Swipe to choose the Group
Presets
Select, the color temperature
Frequencies
Swipe to choose the frequency
Background
Switch to block or white
Info
Bluetooth
Switch on/off
Info| Friendly name| Elinchrom ONE/THREE, can be changed with the
computer or smartphone app.
---|---|---
Firmware rev.|
Sky port ID|
Life time| In hours (hhhh:mm)
Power-on count| How many times the units has been turned on
Flash count| Total flash number
Control panel / Touch Screen
CW: +0.1 f-stop / down
CCW: -0.1 f-stop / up
Display panel – Dashboard
The colour of the Group corresponds to the group number: blue for group
-
yellow for group 2. red for group 3 and green for group 4. The Elinchrom logo on the side of the unit illuminates with the color of the selected group.
-
Group 1-4
-
Modelling lamp menu
-
Battery status
-
Favorite Function: default setting is Mod. Lamp on/off
-
Power value
Modelling lamp
Swipe down to access the modelling lamp menu
Swipe left/right to change values
Short touch to access and change the colour temperature
Screen Views
Work Screen
Shows the most important settings, once the unit is configured. Displayed
automatically after 45 sec of inactivity.
Sub-menu Screen
Select feature by scrolling.
Swipe left or right to change value between the arrows
Screen Lock
To activate the touch screen lock, press the Menu button, select the Setting w heel and go to Touch and select on/off
Connection
The ONE/THREE should only be used between -10°C and 40°C. Only charge between 0°C and 40°C.
USB-C Charger
Use only the original Elinchrom ONE/THREE USB Charger to recharge the bult-in Li-ion battery.
When the unit is OFF the side logo color shows the charge status·
Red : recharging ·
Orange: almost charged
Green: the unit is charged
Recharging time: 100 min. to 100%
Elinchrom ONE: Battery capacity min./max power: 9700/725 flashes per
charged battery.
Elinchrom THREE: Battery capacity min./max power: 11250/525 flashes per
charged battery.
Reset To Default Settings
Switch the unit on, and release the ON button.
When the EL logo appears press immediately the “ON” and “Menu” button for 4
seconds until the display shows ” Reload” all default parameters*.
Elinchrom is n registered trademark of ELINCHROM LTD, ECHANDENS, SWITZERLAND
QSG ONE/THREE – 07.2023
Route de la Venoga 20, 1026 Echandens, Switzerland
Tel. : + 41 21 637 26 77 E-mail :
support@elinchrom.ch
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>