elinchrom 20231107 Pro Skyport Transmitter User Manual

elinchrom 20231107 Pro Skyport Transmitter

Product Information

Specifications

• Classified as a Class 3R laser product
• Complies with IEC/EN 60825-1 Radiation Safety of Laser Products
• Complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s)
• Compatible with Elinchrom EL-Skyport flash units

Introduction
Thank you for choosing ELINCHROM.

Features
The product offers the following features:

• Triggering functionality
• Remote control capability
• Compatibility with Elinchrom flash units
• Class 3R laser safety classification

Installing the Batteries
To install the batteries, follow these steps:

1. Press the battery compartment cover and slide it in the direction of the arrow to open the battery cover.
2. Insert 2 pieces of AA alkaline batteries or AA-type NIMH batteries, ensuring correct orientation of the + and – battery contacts.
3. Press the cover against the transmitter and slide it back into the locked position.

Compatibility
The product is compatible with three different Elinchrom EL-Skyport flash unit generations:

1. 1st Generation
2. 3rd Generation

• Triggering and Remote Control
  The product supports triggering and remote control functionality for all existing Elinchrom flash units with built-in or plug-in EL-Skyport Transceivers. When selecting “ALL” or groups 1 to 4, remote control can be utilized.

• Technical Data
  Tolerances and specifications conform to IEC and CE standards. Technical data is subject to change without notice.

• Hot Shoe Adapter
  The product comes with a hot-shoe adapter for mounting on the camera.

• Display
  The product features a display for easy navigation and settings adjustment.

• Buttons
  The product includes various buttons for controlling different functions and settings.

• Elinchrom TTL
  The product supports Elinchrom TTL functionality for compatible flash units.

• Setup Menu
  The product has a setup menu for customizing settings and preferences.

• Manufacturing Reset
  A manufacturing reset option is available to restore the product to its original factory settings.

• Troubleshooting
  If you encounter any issues with the product, refer to the troubleshooting section in the user manual for assistance.

• Firmware Update
  Instructions for updating the product’s firmware can be found in the user manual.

FAQs

• Q: What are the battery requirements for this product?
  A: The product requires 2 pieces of AA alkaline batteries or AA-type NIMH batteries.

• Q: Is this product compatible with all Elinchrom flash units?
  A: Yes, triggering works with all existing Elinchrom flash units with built- in or plug-in EL-Skyport Transceivers.

Tolerances and specifications conform to IEC and CE standards. Technical data is subject to change without notice.

INTRODUCTION

Dear Photographer,
Thank you for choosing ELINCHROM.

• All Elinchrom products are manufactured using the most advanced technology. Carefully selected components are used to ensure the highest quality and the equipment is subjected to many tests both during and after manufacture. We trust that it will give you many years of reliable service.

• Please read this User Manual carefully before you use your new Elinchrom product. You will find information for your safety and how to benefit from all the programmable features.

• This Manual may show images of products with accessories that are not part of sets or single units. Elinchrom set and single unit configurations may change without advice and may differ in other countries.

• For further details, upgrades, news and the latest information about the Elinchrom system, please regularly visit the Elinchrom website. The latest user guides and technical specifications can be downloaded from the
  “Support” area.

• Technical data, features and functions of Elinchrom flash units and accessories may change without notice. The listed specifications can differ due to tolerances in components or measuring instruments. Technical data is subject to change. No guarantee for misprints.

• Please check for the most recent manual at our website: www.elinchrom.com/support.

Thanks,
Your Elinchrom-Team

• The Product is classified as a Class 3R laser product, according to the following standards IEC/EN 60825-1 “Radiation Safety of Laser Products”.
• Class 3R: A Class 3R Laser is considered safe if handled carefully, with restricted beam viewing. With a class 3R laser, the MPE can be exceeded, but with a low risk of injury. Visible continuous lasers in Class 3R are limited to 5mW. For other wavelengths and for pulsed lasers, other limits apply.

DECLARATION OF CONFORMITY USA AND CANADA

This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product complies with the Canadian ICES-003 Class B specifications.

Radiation Exposure Statement
This equipment complies with portable RF exposure limits in Canada and the USA set forth an uncontrolled environment and is safe for intended operation as described in this manual. Further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body.

FCC Class B Compliance note
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device is limited to operation on permissible Part 15 frequencies, and it cannot be configured by end users or professional installers to operate outside the authorized bands.

ELINCHROM TRANSMITTER PRO

VERSIONS
The Elinchrom Transmitter Pro is available for the following compatible cameras

• Canon
• Nikon
• Fujifilm
• Sony
• Pentax

FEATURES

• Elinchrom TTL with compatible Elinchrom TTL flash units.

• Manual mode, compatible with Elinchrom flash units with built-in Skyport Receivers.

• Large graphic control display.

• Backlight in green or red (green for Normal Sync Mode, red for Speed Sync Mode).

• Fast access buttons and a rotating wheel for easy control.

• Secure Hot-Shoe connection with bayonet locking system.

• Standard 2 AA Batteries (Accepts rechargeable batteries).

• 2.5mm phone jack trigger output, for direct synchronisation with a flash unit.

• Firmware update with integrated Mini-USB socket.

• 40 remote channels.

  • 20 frequency channels in Normal Sync mode.
  • 20 frequency channels in Speed Sync mode.
    (For all the latest Elinchrom flash units with 20 frequency channels.)

• 4 Groups and ALL.

• EL-Skyport Sync Modes.

  • Normal Sync Mode (maximum distance range).
  • Speed Sync Mode (with compatible cameras, but reduced distance range).

• Sync Modes:

  • Automatic controlled Hi-Sync or HSS up to 1/8000s).*
  • Second curtain mode.***
  • ODS (Over-Drive-Sync) fine-tune the time delay at fast shutter speed settings, from 0.1 to 5.0 ms.

• Auto MOD *** to control the modelling light of the Elinchrom flash units for focusing.

  • Shutter Mode** (half-pressed shutter release controls the modelling lamps).
  • DOF Mode (The camera “DOF” button controls the modelling lamp).

• AF Light integrated.****

• Remote Control with automatic feedback from Elinchrom flash units.

  • EL-flash units can be controlled “All” together, in “Groups” or “single” units.
  • Flash power up & down.
  • Modelling lamp on/off.
    (For all the latest Elinchrom flash units with 20 frequency channels.)

• Sleep mode and Auto OFF mode are programmable.

• Manufacturing RESET.

  • For Nikon® activate the camera menu for the fast sync speed settings.
  • Not supported by Nikon®
  • Not supported by Sony®, Fujifilm®
  • Not supported by mirrorless cameras of any brand

INSTALLING THE BATTERIES

• Press the battery compartment cover and slide it in the direction of the arrow to open the battery cover (See Picture 1).
• Insert the batteries. Make sure the “+” and “-” battery contacts are correctly oriented (See Picture 2).
• (Note: Please use 2 pieces of AA alkaline batteries or AA-type NIMH batteries).
• Press the cover against the Transmitter and slide it back into the locked position.

BATTERIES

• 2x AA batteries are used for the Transmitter.
• Installing the batteries improperly will not damage the Transmitter.
• Non-rechargeable (dry cell) AA batteries like zinc–carbon, Alkaline types or rechargeable batteries in the AA size such as nickel-cadmium (NiCd) or nickel-metal hydride (NiMH) can be used.
• Do not mix battery types.
• Do not use Lithium AA batteries in this Transmitter.

COMPATIBILITY

There are three different Elinchrom EL-Skyport flash unit generations in the market:

• 1ST GENERATION
  • EL-Skyport Transceiver RX module (Style RX, Digital RX, Ranger RX).
• 2ND GENERATION
  • Built-in EL-Skyport module Mk1 (BRX, D-Lite RX, Quadra, Quadra Hybrid).
• 3RD GENERATION
  • Built-in Skyport module Mk2 (ELC and ELB). This generation offers an extended distance range

TRIGGERING
Triggering works with all existing Elinchrom flash units with built-in or plug-in EL-Skyport Transceivers.

REMOTE CONTROL

WHEN ALL OR GROUP 1 – 4 IS SELECTED

• All Elinchrom flash units with EL-Skyport are supported when changing “PWR±, or MOD on/off”.
• Some units do not support the modelling lamp on/off feature, “–“ is then displayed (i.e. for Ranger, Quadra. The modelling light of the ELB400 can be switched on/off but the display shows “–“).

WHEN A SINGLE UNIT IS SELECTED

• The selected unit is highlighted with a frame in the display and can be controlled individually.
• Only Elinchrom flash units with built-in EL-Skyport receivers of the 2nd and 3rd generation are supported.

Note:
1st Generation units are detected, but will show “–“ in the display. There is no feedback on the unit settings for the Elinchrom Transmitter Pro, but they will be triggered normally.

FREQUENCY CHANNELS

• Some older Elinchrom flash units with EL-Skyport built-in will support Frequency channels 1 to 4 or 1 to 8 (such as BRX, D-Lite RX, and Quadra).
• The latest Elinchrom flash units with EL-Skyport built-in will support up to 20 different Frequency channels 1 to 20 (ELC, ELB).

TECHNICAL DATA

Receiver or Transceiver and the EL-Skyport RX Transceiver modules, plus EL- Skyport Universal.
REMOTE CONTROL COMPATIBILITY| please refer to the compatibility chart online
DISTANCE RANGE| Indoor > 60m. Outdoor > 200m. Note:

Only the latest Elinchrom flash units from the ELC and ELB series will offer the full distance range. Other series, or classic Elinchrom flash units will have a limited distance range.

BATTERIES| 2x AA batteries (standard or rechargeable).
BATTERY LIFETIME| Depends on the type of batteries and the usage.

For two standard batteries with 1000mAh each it is approx. 35 hours of working time and more than 15000 trigger releases.

REMOTE CONTROL| Max. 10 units can be detected displayed and remote controlled.
FREQUENCY CHANNELS| 20 channels in Normal mode and 20 channels in Speed mode.
EL-SKYPORT MODES (ELSP)| Normal/Speed – Sync mode.
TRIGGER/CONTROL GROUPS| “All” or in “Groups”(Group 1 to 4).
SYNC MODES| Standard, ODS, Second Curtain, automatic Hi-Sync or HSS
USB SOCKET| For firmware updating.
SR SOCKET| Trigger Output 2.5mm Phone Jack mono (max. sync-voltage 3VDC).
DIMENSIONS (W x L x H)| 69 x 84 x 59 mm (2.7x 3.3x 2.3 inches)
WEIGHT| Approx. 170g (6 oz), including 2x AA batteries.

120g (4.2 oz) without batteries.

HOT-SHOE ADAPTER

FEATURES
The hot-shoe adapter offers special connection pins for communication with the attached camera. There are four different Elinchrom Transmitter variants available

• Canon® for Canon® EOS type A cameras with ETTL II / ETTL features

• Nikon® for Nikon® cameras with iTTL features

• Sony®, Olympus®, Panasonic®, and other brand will follow later.
  The communication with the camera is required to benefit from the extra features like:

• SYNC Mode

  • Hi-Sync, HSS and ODS Mode
  • Second Curtain
  • TTL

• Auto MOD

• AF Light

Note: Not all cameras support all features!

LIST OF TESTED CAMERAS
The latest summary of camera models and supported features can be found on the Elinchrom website at: http://www.elinchrom.com/support.php

MOUNTING ON THE CAMERA

An easy-locking bayonet mechanism is used to lock the Transmitter securely into the Camera’s hotshoe.

ATTACHING

1. Turn off the camera and the Elinchrom transmitter.
2. Align the transmitter hotshoe with the camera’s hotshoe mount.
3. Slide it into the camera’s hot shoe mount.
4. Move the tab on the locking ring to the right until it clicks in place. (See picture 3)

DETACHING

• Unlock: press the lock-release button and move the tab to the left. (see picture 4)
• Slide the EL-Skyport transmitter off the camera’s hotshoe mount.

DISPLAY

• The graphic display shows the status and settings of the Elinchrom unit when set to Manual mode.
• The display illumination can be switched on or off.
• In Normal Sync mode, the illumination is green. In Speed Sync mode, the illumination is red.
• The contrast of the display can be adjusted in the setup menu.
• The top bar of the display shows the status of the Elinchrom Transmitter.
• The bottom bar in the display shows the functions of the 4-speed buttons.
• The middle area shows a list of the Elinchrom flash units detected, It also shows setup items for the Setup menu when selected.

DISPLAY PANEL – DASHBOARD

• Not supported by Nikon®
• Not supported by Sony®, Olympus®, Panasonic®
• Not supported by some Sony®,Olympus® and Panasonic® cameras

BUTTONS

SPEED BUTTONS 1-4
The speed buttons enable quick setting of the functions indicated below.

SPEED BUTTON 1 (LEFT)
TTL / Manual Mode: toggle between TTL and Manual mode.

SPEED BUTTON 2 (MIDDLE LEFT)

• TTL Mode: switch Groups All or 1 to 4 on/off, when On; change EV value with the rotation ring from -3.0 to +3.0.
• Manual Mode: select a displayed flash unit and change the flash power value with the rotation ring.

SPEED BUTTON 3 (MIDDLE RIGHT)

• TTL Mode: switch the modelling lamp on/off.
• Manual Mode: switch the modelling lamp on/off.

SPEED BUTTON 4 (RIGHT)

• Setup:
  press this button to enter into the setup menu. Select the dial feature, press the middle button of the rotation ring to confirm change the value again with the dial and press the middle button again to confirm.

• Exit
  Exit the Setup menu and switch back to standard display mode.

ELINCHROM TTL

Get the perfect shot right from the start.

WHAT IS REQUIRED:

• The Elinchrom Transmitter Pro (Includes the TTL mode. Nikon and Canon are available, more brands will follow).
• Elinchrom TTL flash unit (ELB 500 TTL)
• A compatible camera (The compatible cameras are listed at: http://www.elinchrom.com/support/.

ELINCHROM TRANSMITTER PRO TTL FEATURES

• Groups: All or 1 to 4 can be selected individually by pressing the Group button.
• Groups on/off: All or Groups 1 to 4 can be selected individually by pressing the Group button, to switch the selected Group on/off use the speed button middle/left.
• EV value: The EV can be adjusted from -3 to +3 in 1/3 f-stops with the rotation ring. All or individual Groups can be selected with the Group button to adjust the EV value.
• Modelling lamp on/off: The modelling lamp can be switched on/off with the speed button middle/right. All or individual Groups can be selected with the Group button.
• For further options and settings please read the user manual of the Elinchrom TTL flash unit.
• TTL values are saved while switching to “Manual” mode.

ON/OFF
Press and hold for min. 2 seconds to switch the Elinchrom Transmitter Pro On/Off.

GROUP BUTTON
TTL / Manual Mode: Press to toggle between 1 through 4 Groups and “ALL.”

TEST BUTTON (WITH EL LOGO)
Pressing the TEST button will fire all flashes when “ALL” is selected or any single Group, 1 through 4 is selected. Please remember, if flashes should be triggered in just one selected Group, the photocell must be deactivated.

REFRESH BUTTON

• Press the Refresh button any time the power setting has been done on a separate EL flash unit to update the power setting display of the Transmitter Pro.
• If a Group is selected, only the information for that selected Group will refresh.
• When “ALL” is selected, information for all Groups will be refreshed.
• A flash that was not scanned and found when the Transmitter Pro was switched ON cannot be added with the Refresh feature.
• If a flash is added, select SETUP and SCAN in the setup menu or switch the Transmitter Pro OFF and ON again.
• The refresh can take several seconds, depending on how many flash units are found and operated by the Transmitter Pro.

Note:
To update the display information after flash power changes have been applied directly to the flash unit, please press the REFRESH button. Changes are not automatically updated, to avoid interferences with the flash triggering.

ROTATION RING
Turn the rotation ring to select various functions (up & down) and change the power levels of the EL flashes.

SET/CONFIRMATION BUTTON (ROTATION RING)

• Press to confirm a modification made in the Setup menu.
• Press to switch on the display illumination.
• Press to return to normal operation when the Transmitter Pro has switched to Standby mode.
• Press 2s to lock all functions and settings. Press again to unlock.
• The locking feature blocks the function of the dial and other buttons to prevent unwanted changes of settings while carrying the Transmitter Pro.

SETUP MENU

SCAN

• When the Transmitter Pro is switched ON, it will automatically search for Elinchrom flash units with built-in or plug-in EL-Skyport Transceiver modules.
• The Scan feature is also available in the Setup Menu. A re-scan is required when new flash units have been added to the lighting setup.

To find EL flash units

• all EL flash units must be switched on and the Skyport Receiver must be activated.
• all flashes must have a built-in or plug-in Skyport Transceiver RX module.
• the Transmitter Pro and the EL flash unit must have the same frequency channel settings.

FREQUENCY CHANNELS
Up to 20 Skyport frequency channels can be selected.

Note:

• Only the latest Elinchrom flash units (ELC and ELB) will support up to 20 frequency channels.
• All “RX” flash units will support up to 8 channels and some older Elinchrom flash units support up to 4 channels.

ELSP MODE
The Transmitter Pro has two operating modes that offer different shooting functionality.

• Normal Sync mode (Maximum distance range)
  • Normal mode is compatible with the very first Elinchrom flash units incorporating Skyport.
  • When selected, display illumination and status LED will light up in green.
• Speed Sync mode (limited distance range)
  The Speed mode enables faster communication and shutter speeds for compatible cameras (i.e. for leaf shutter cameras and some mirrorless). The Hi-Sync or HSS mode activates automatically when faster shutter speeds within 1/8000s are selected with compatible cameras, in both Normal and Speed modes. The display illumination and status LED are displayed in red when speed mode is selected.

Note:

• The Speed mode reduces the working distance by approximately 50%.
• The transmitter and the EL flash units must have the same Sync mode settings, either Normal or Speed.
• Speed Sync mode should not be confused with Hi-Sync or HSS. The Hi-Sync or HSS feature is automatical available in both Normal or Speed modes with compatible cameras.

ODS SETUP

• The Over-Drive-Sync (ODS) can improve the overall exposure at fast shutter speed settings.
• ODS relies on flash units with long flash durations. The results will depend on the flash duration of the lights used (which also change at different power levels) and can vary with different types of cameras. Full frame cameras with large sensors and slow shutters are unfortunately the hardest to get good results with, but lights with long enough flash durations can still achieve clean frames to 1/8000th.
• With ODS fine-tuning, up to 2 f-stops, more light is possible, essential when sunlight must be overpowered.
• The ODS Setup offers adjustment from 0.1 to 5.0 ms or can be switched off. The ODS value will vary depending on the camera and the flash unit that is used and must be adjusted manually.

Note:

• When ODS is adjusted, the position of the flash cutoff (dark edge at the top or bottom of the picture) can be moved within the frame.
• When switched OFF, the flash trigger point will be selected automatically at the higher shutter speed settings of the camera.

AUTO MOD

• Off
  The modelling light of the Elinchrom flash unit will not change.

• Shutter**
  Pressing the camera’s shutter button for focusing will switch on the modelling lamp for a few seconds as an aid to focusing in low light. (Not supported by Nikon)

• DOF
  The Elinchrom flash unit will switch on the modelling lamp for as long as the DOF (Depth of field) button on the camera is held.

AF LIGHT
Activates the Auto-Focus assist light of the Transmitter Pro when the shutter release is half-pressed for focusing (check also camera settings).

• KEY CLICK
  When activated, pressing any control button will be indicated by a beep tone.

• SLEEP

  • When not used for a time, the Transmitter Pro will switch to Sleep Mode to save battery power.
  • Delay Sleep mode from 1 to 60 minutes or turn OFF.

• AUTO-OFF

  • The Transmitter Pro will automatically turn OFF when left unattended for a time.
  • Delay auto-off starts from 1 to 60 minutes or turns OFF.
  • When Sleep mode and Auto Off are both active, the Transmitter Pro will switch the power OFF at the user-set Sleep Mode delay.

• CONTRAST
  The display contrast can be adjusted from 80 to 120%

• BACKLIGHT
  The display illumination of the device can be switched on/off

MANUFACTURING RESET

Pressing and holding the left and right Speed buttons for approximately 2 seconds, whilst the Transmitter is switched on, will reset the Transmitter Pro to manufacture settings. All user settings, except the display contrast, will be reset.

FIRMWARE UPDATE
To update the Firmware of the Transmitter Pro, the Elinchrom Updater is required. Available from the Elinchrom website.

• Not supported by Nikon®.
• Not supported by Sony® and Olympus®/Panasonic®.

TROUBLESHOOTING

• Pressing and holding the left and right Speed buttons for approximately 2 seconds will reset the Transmitter
• Pro manufacture settings. All user settings, except the display contrast, will be reset.

HAVING THIS PROBLEM?

|

PLEASE CHECK THE FOLLOWING POINTS:

---|---
THE UNIT IS NOT SWITCHING ON| •        Check battery polarity and replace both discharged batteries.
FLASH UNIT CAN BE TRIGGERED WHEN THE MODE “ALL” IS SELECTED| • Transmitter and receiver must have the same frequency channel settings.

•        ELSP MODE: transmitter and receiver must have the same synchronisation mode settings: normal or speed sync mode.

•        Check that the Skyport receiver in all EL units with built-in receivers is switched on.

•        Check that the transmitter version corresponds to your camera brand.

SOME UNITS ARE NOT TRIGGERING WHEN THE GROUP MODE IS SELECTED| •        Check the Group settings of the EL-flash unit.

•        Reduce the distance to any unresponsive unit.

•        Transmitter and receiver must have the same synchronisation mode settings: normal or speed sync mode, and frequency channel settings.

THETESTBUTTONWORKS, BUT THE CAMERA WILL NOT TRIGGER FLASH UNITS| • Check the hot shoe fitting.

•        Check the camera settings (turn hotshoe communication on).

•        Check that the transmitter version corresponds to your Canon or Nikon camera.

•        Check the list of compatible cameras.

SOME INFORMATION IS NOT DISPLAYED ABOUT DIGITAL RX, RANGER RX OR STYLE RX UNITS| •        Units equipped with a plug-in Transceiver RX are limited in remote features. These units can however be triggered and controlled (but with no visual feedback) by the Transmitter Pro.

•        Update the firmware of the Transmitter Pro.

LIMITED DISTANCE RANGE:| •        Reposition the units.

•        Increase the distance from walls and ceilings.

•        ELSP Mode: In speed sync mode the distance range is reduced by approximately 50 %, so switch back to normal sync mode.

•        Outdoors, the distance range could be reduced due to humidity, interference, obstacles etc.

---|---
INTERFERENCE WITH OTHER 2.4 GHZ NETWORKS, UNRELIABLE TRIGGERING:| •        Try another frequency channel for both the transmitter and the receiver of the EL unit.

•        Reduce the distance between the flash unit and Transmitter Pro.

AUTOMATIC HI-SYNC / HSS MODE; SYNC UP TO 1/8000S:| •        Elinchrom Action (previously A) heads are not optimised for the Hi-Sync/HSS. To benefit from better performance please use flash units with Hi-Sync or flash tube heads.

•        ODS fine-tuning helps to optimise Hi-Sync performance.

•        If there is visible banding please reduce the shutter speed on your camera, or set ODS and adjust to minimise or avoid banding.

•        Hi Sync / HSS functionality only works with compatible cameras and the appropriate Transmitter Pro and when the camera is set to shutter speeds above 1/250s.

SCANNING EL-UNITS: NO EL-UNIT FOUND, OR SOME UNITS ARE MISSING.| • Switch on all enabled EL units, then switch on the EL-Skyport Transmitter Pro or go to setup and rescan.

•        Frequency, group and ELSP mode settings must match with the Transmitter Pro.

•        Ensure that all Skyport-enabled units are operating on the latest firmware.

FREQUENCY CHANNEL FOR EL-SKYPORT SPEED RECEIVERS
This is not relevant to this product, but it may help with frequency set-up on legacy EL-Skyport units.

• DOWNLOAD THE ELINCHROM TRANSMITTER PRO USER GUIDE
  Obtain the complete user guide using this link:

• DOWNLOAD CONFORMITY
  Find your declaration for EC and USA & Canada conformity here: http://bc.gs/ec.

• FIRMWARE UPDATE BY USB PORT
  Please download our latest firmware and follow the instructions: http://bc.gs/fw.

References

• Elinchrom | What's your next adventure?
• Elinchrom | Support
• Elinchrom | Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>