FX3D DESIGN MK8 Rock Guards Installation Guide

MK8 Rock Guards

“`html

Specifications:

• Product: Rock Guards
• Vehicle Compatibility: Volkswagen Golf R & GTI (2022+)
• Material: 1/16 (1.75mm) thick plastic
• Includes: Front rock guards (x2), rear rock guards (x2),
  plastic washers (x4), FX3D Design T25 Torx screwdriver (x1), 3M VHB
  double-sided tape & alcohol wipes (x4)

Product Usage Instructions:

Front Rock Guards Installation – Part 1/2

1. Turn your vehicle’s front wheels to access the factory fender
   liner screws.

2. Using the provided T25 Torx screwdriver, unscrew the 2
   screws.

3. Place the washers through the OEM screws and insert both screws
   through the rock guard’s slotted holes.

4. Align and partially screw the 2 screws into the fender liner
   without tightening completely.

Front Rock Guards Installation – Part 2/2

1. Adjust the rock guard position until satisfied.

2. Tighten the screws securely but avoid over-tightening.

3. Clean the fender lip and guard using the provided alcohol
   wipes.

4. Apply the 3M VHB double-sided tape and press firmly. Allow at
   least 24 hours for optimal adhesion.

5. Repeat steps on the other side of the vehicle.

Rear Rock Guards Installation – Part 1/2

1. Raise the rear of your vehicle with a car jack to access the
   rear wheel arch liner screws.

2. Remove the 2 screws using the provided FX3D stubby
   screwdriver.

3. Slide the factory screws through the slotted bracket of the
   rear rock guard.

Rear Rock Guards Installation – Part 2/2

1. Screw the factory screws into their positions without full
   tightening for adjustment.

2. Adjust the rock guard position to your liking.

3. Securely tighten the screws without over-tightening.

4. Clean the bumper lip and guard using the alcohol wipes.

5. Apply the 3M VHB tape, press firmly, and allow at least 24
   hours for optimal adhesion.

6. Repeat steps on the other side of the vehicle.

FAQ:

Q: How long should I wait before driving after
installing the rock guards?

A: It is recommended to wait for at least 24
hours after installation before driving to ensure proper adhesion
of the rock guards.

“`

INSTALLATION GUIDE
Volkswagen Golf R & GTI (2022+)
ROCK GUARDS

www.fx3ddesign.com

Questions?
info@fx3ddesign.com

PREPARING FOR INSTALLATION

What’s in the package?

A. Front rock guard (x2)

B. Rear rock guard (x2)
B
C. 1/16″ (1.75mm) thick plastic washer (x4)

D. FX3D Design T25 Torx screwdriver (x1)

A

E. 3M VHB double sided tape & alcohol wipe (x4)

C

D

E

Required tools
· T25 Torx screwdriver (included) · Car Jack

FRONT ROCK GUARDS INSTALL – 1/2

B
A. Turn your vehicle’s front wheels
as much as possible to allow access to the 2 factory fender liner screws shown on the image above.
B. Using a T25 Torx screwdriver,
unscrew the 2 screws.

B
A. Grab the front rock guard. FX3D
logo should be facing the rear of the car.
B. Place the provided washers(C)
through the OEM screws you have just removed.
C. Insert both screws through the
slotted holes of the rock guard.
D. Align and screw the 2 screws into
the fender liner. Don’t tighten all the way to allow positionning of the rock guard to your liking.

FRONT ROCK GUARDS INSTALL – 2/2

C

A. Move the rock guard from side to
side until you are satisfied with its position.
B. Once you’re done, you can fully
tighten the 2 screws. Don’t over tighten.

A. Gently pull on the top part of the
guard to reveal the fender inner lip.
B. Using the provided alcohol
wipes(E), clean the fender lip and the rock guard.
C. Install one strip of 3M VHB(E)
double side tape on the fender and remove the red plastic backing.
D. Apply a good amount of pressure
to the guard. 3M VHB tape needs to sit at least 24h in order to acheive optimal adhesion.
E. Repeat steps 1 to 4 on the other
side of the vehicule.

REAR ROCK GUARDS INSTALL – 1/2

B

A. Using a car jack, raise the rear of
your vehicule to gain more room to access the rear wheel arch liner screws.
B. Remove the 2 screws shown on the
image above. This is where the supplied FX3D stubby screwdriver(D) comes in handy.

A. Grab the rear rock guard. FX3D
logo should be facing the rear of the car.
B. Slide the 2 factory screws through
the slotted bracket of the guard like shown on the image above.

REAR ROCK GUARDS INSTALL – 2/2

A. Align the rock guard and screw the
2 factory screws into their respective positions. Don’t fully tighten to allow for adjustment.
B. Move the rock guard from side to
side until you are satisfied with its position.
C. Once you are done, you can fully
tighten the 2 screws. Don’t over tighten.

A. Gently pull on the bottom part of
the guard to reveal the bumper inner lip.
B. Using the provided alcohol
wipes(E), clean the bottom section of the bumper lip and the rock guard.
C. Install one strip of 3M VHB(E)
double side tape on the bumper and remove the red plastic backing.
D. Apply a good amount of pressure
to the guard. 3M VHB tape needs to sit at least 24h in order to acheive optimal adhesion.
E. Repeat steps 1 to 4 on the other
side of the vehicule.

References

• FX3D Design | Adjustable low profile fender Rock Guards

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>