tp-link RM100 Router WiFi 4G LTE 300MBPS User Manual

tp-link RM100 Router WiFi 4G LTE 300MBPS

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC Caution

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20cm is maintained between the antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna,
3. For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4Gband by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.

As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IMPORTANT NOTE

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labelling

The final end product must be labelled in a visible area with the following:
“Contains certifified FCC ID: 2AXJ4RM100”.
“Contains certifified IC: 26583-RM100”.

Manual Information to the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.

Overview

The RM100 Wi-Fi module provides a highly-integrated and flexible platform for developing and evaluating products and applications based on the RTL8720CM-VT2 SoC. The RM100 Wi-Fi module can be either used with development kit for software development or incorporated into OEM products to enable rapid deployment of Wi-Fi connected systems.

The module includes the following components:
RTL8720CM-VT2 chip
An integrated Balun
4MB SPI Flash
Shield

2Interface and pinout

Interface:
UART
Power supply

Pinout:

Electric Feature

Mechanic Feature

Size: 18mm23.5mm3.9mm

Wireless Feature

Operating Frequency: 2.4GHz:2412~2462MHz
Transfer  Rate: 802.11b: 11/5.5/2/1 Mbps
802.11g: 54/48/36/24/18/9/6 Mbps
802.11n: up to 72.2 Mbps
Wireless Channel: ch1-ch11
Transimit Power:18.49dBm(max)
Antenna Type: external antenna with Ipex port

Physical and Environmental

Operating Temperature: 0℃～40℃
Storage Temperature: 0℃～40℃
Working Humidity: 10%～90% RH

Additional Description

The module will be installed inside another device. And the outside of the device into which the module is installed will display a label referring to the enclosed module.
This exterior label will use the wording such as “Contains FCC ID: 2AXJ4RM100”, or any other similar wording that expresses the same meaning.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>