FX3D DESIGN 2017-21 Honda Civic Type R Rock Guards Installation Guide
- August 10, 2024
- FX3D DESIGN
Table of Contents
FX3D DESIGN 2017-21 Honda Civic Type R Rock Guards
Product Information
Specifications
- Product: Rock Guards
- Vehicle Compatibility: Honda Civic Type R (2017-2021)
- Manufacturer: FX3D Design
- Website: fx3ddesign.com
Product Usage Instructions
Preparing for Installation
What’s in the package?
- A. Front rock guard (x2)
- B. Rear rock guard (x2)
- C. #10 x 1/2 (15mm) truss head screw (x2)
- D. #10 u-nut (x2)
- E. #8 x 3/4 (19mm) self-tapping screw (x2)
- F. #8 spring u-nut (x2)
- G. Strip of 3M VHB double-sided tape (x2)
Frequently Asked Questions (FAQ)
-
Q: Can I adjust the position of the rock guards?
A: Yes, the rock guards can be adjusted to poke out more or less based on personal preference. -
Q: Is there an alternative to using screws for installation?
A: You can use the provided 3M VHB double-sided tape instead of screws for installation if preferred.
INSTALLATION GUIDE
Honda Civic Type R (2017-21)
ROCK GUARDS
PREPARING FOR INSTALLATION
What’s in the package?
- A. Front rock guard (x2)
- B. Rear rock guard (x2)
- C. #10 x 1/2” (15mm) truss head screw (x2)
- D. #10 u-nut (x2)
- E. #8 x 3/4” (19mm) self-tapping screw (x2)
- F. #8 spring u-nut (x2)
- G. Strip of 3M VHB double-sided tape (x2)
Required tools
- Phillips screwdriver or drill
- Push type fasteners removal tool or flat head screwdriver
- Car Jack
- Wheel nuts removing socket and wrench
- Heat gun or air dryer
FRONT ROCK GUARDS INSTALL – 1/2
Tips before the installation
- Our rock guards should be installed with the logo facing the rear of the car.
- They can be adjusted to poke out more or less depending on your personal preference.
- Turn your vehicle’s front wheels as much as possible to allow access to the fender liner screws/clips.
- Remove the 3 Phillips head screws and the plastic clip indicated on the image. To remove the clip, push the middle pin completely and use the appropriate clip-removing tool to pry it out of the fender.
- Pull on the fender liner to expose the fender tab.
- Grab one of the provided u-nut(D) and screw(C) that came in the front rock guards’ package.
- Slightly pry open the u-nut to facilitate the installation and avoid scratching the paint.
- Slide the u-nut on the fender tab making sure that the flat face is facing towards you.
- Grab the front rock guard (FX3D logo should be facing the rear of the car).
- Put one of the provided screw(C) through the upper slotted hole and screw it into the fender liner as shown on the image.
- Don’t tighten all the way to allow for later adjustment.
- Install the 3 factory screws through the rock guards’ slotted holes and into their original spot on the fender liner.
- Adjust the mud flap to the desired position and fully tighten all screws. Don’t over-tighten.
- Repeat steps 1 to 3 on the other side of the car.
Tips before the installation
We provide size #8 self-tapping screws in order to provide a secure
installation while not leaving a noticeable hole in the diffuser inner lip if
you ever remove our mudguards.
3M VHB double-sided tape can also be used instead.
- Jack you car up so you can remove the rear wheel and gain access to the bumper inner lip.
- Remove the lower factory screw using a Phillips screwdriver.
- Grab the rear mud flap (FX3D logo should be facing the rear of the car).
- Put the factory screw through the upper slotted hole of the guard and screw it back into the bumper as shown on the image.
- Don’t tighten fully to allow the rock guard to rotate freely.
- Rotate the mudguard to align the lower hole with the middle of the diffuser’s inner lip.
- Mark the spot with a marker pen.
- Grab one supplied spring u-nut(F) and slightly pry it open to ease installation.
- Slide it on the diffuser inner lip making sure that the flat face is facing toward you and that the hole is sitting in the middle of the marked spot.
- Align the lower hole of the rock guard with the U-nut.
- Using a screwdriver or an electric drill, screw one of the provided self-tapping screws(E) into the bottom hole of the mudguard and through the u-nut and diffuser lip.
- Don’t tighten all the way to allow for later adjustment.
- Adjust the mud flap to the desired position and fully tighten both screws. Don’t over-tighten.
- Repeat steps 1 to 4 on the other side of the car.
ATTENTION
We recommend installing the rear mud guards using the provided nuts and screws
for a sturdier installation.
Nevertheless, you can use the provided 3M VHB double-sided tape if you prefer
not to drill into the factory diffuser lip.
In that case, skip steps 3 and 4.
IMPORTANT
Clean the diffuser inner lip AND the rock guard with a degreaser agent.
3M VHB DOUBLE SIDED TAPE needs to sit at least 24h in order to achieve perfect
adhesion.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>