UTHFY 7105 Tower PTC Heater User Manual

UTHFY 7105 Tower PTC Heater

introduction

ATTENTION

1. Check all accessories and perform a test before the final installation.
2. Avoid using a high-pressure water gun to clean the screen and cameras, the product is only rainproof.
3. Refrain from using alcohol, stain removal solutions, or corrosive solvents to clean the screen and lens, as it may damage the product’s appearance and waterproofing.
4. Ensure all units are connected before powering on.
5. Do not fold the cable lines during installation.
6. Use a certified 32-128GB MICRO TF memory card with a CLASS 10 rating or higher, and format the memory card before initial use.
7. Prolonged memory card use can lead to fragmentation; we recommend regular memory card formatting.
8. After inserting the TF card, press the rubber plugs to maintain the product’s waterproof performance.

Description of Main Parts and Key Functions

Wire Diagram

Connection Method

1. Set the multi-meter to DC mode. Connect the black test lead to the negative battery pole and the red test lead to the test line.
2. With the ACC (Accessory) turned OFF, there should be no output, and the multi0meter should show no voltage. When the ACC is turned ON, the multi0meter should read 12V, indicating the presence of ACC power.

NOTE : If you haven’t found the ACC line, please use the red test lead to repeatedly check different lines (keeping the black test lead connected to the negative pole) until you locate the ACC power line.

Description of the Main Screen Menu

• A: Recording Time B: Resolution
• C: GPS
• D: Bluetooth
• E: WIFI
• F: G-sensor
• G: Memory Card
• H: Display Brightness
• Adjustment
• I: Volume Adjustment

1. Motorcycle Dash Cam : Click to enter the interface and settings.
2. Carplay : Click to connect Carplay.
3. Android Auto : Click to connect Android Auto.
4. GPS Information : Click to view GPS status, altitude, bearing and other information.
5. Playback : Click to view the recorded videos.
6. Settings : Click to enter the menu settings.
7. Bluetooth : Click to connect Bluetooth.

CarPlay & Android Auto Connection Instructions

Click Carplay or Android Auto according to your preference.

NOTE : For the initial connection, turn on your cell phone’s Bluetooth, connect to the host’s Bluetooth, and wait for 5-10 seconds. A pop-up window will appear on your phone for CarPlay. After authentication, the Bluetooth connection will automatically disconnect, and your phone’s CarPlay interface will transmit. On subsequent startups, it will connect automatically as long as the host’s Bluetooth and Wi-Fi are enabled, requiring no further action.

NOTE : For the initial connection, turn on your cell phone’s Bluetooth, connect to the host’s Bluetooth, and wait for 5-10 seconds. When your phone’s Wi-Fi is turned on, the Android Auto interface will automatically transmit. Click the home button to return to the main dash cam interface.

Tire Pressure Page

Displays tire pressure, tire temperature, speed, altitude, direction, and position.

Main Settings Description (Accessed via Settings)

1. Pressure : Pairing for tire pressure detection.
2. Screen Saver : Set the auto-lock time of the screen.
3. GPS info: Check GPS signal information.
4. Language : Multiple languages for selection.
5. Time setting : Set the host time (the host will update the time automatically after connecting to GPS/Wi-Fi/Bluetooth).
6. Phone Audio: Toggle ON/OFF (when set to OFF, mobile phone sound plays through the host).
7. Key Volume : Toggle ON/OFF for touch key tones.
8. WiFi Switch : Toggle ON/OFF (Wi-Fi connection range is 10 meters straight without obstructions).
9. Format SD : Format the memory card.
10. Reset factory : Reset the host.
11. Version : Check the version, Bluetooth name, Wi-Fi name, and password.

Tire Pressure Detection Interface Explanation

Click to access tire pressure settings.

1. Choose the tire pressure unit (Bar or Psi) based on your preference.
2.  Set the air pressure alarm value suitable for your vehicle model. If tire pressure goes below or above this set value, a flashing reminder will appear.
3. Start by installing the reverse nut to the bottom of the tire valve. Click START. The FRO tire pressure number at the top will flash. Set the front wheel A (FW) until the blinking stops. Continue with the rear wheel B (RW) while BAC is blinking until the blinking stops. After successfully pairing the front and rear tire pressure sensors, screw the reverse lug nuts against the tire pressure sensors to secure them.
4. When reinflating the tire, first loosen the reverse nut, then screw the sensor. After inflation, the tire pressure will display without needing to pair again. If the value isn’t displayed, ride for a certain distance; it should then appear. If not, follow the pairing steps again.
5. If the tire pressure display is inaccurate, check the sensor’s correct installation and ensure the inflation tool’s air pressure unit matches the host.

Note : The tire pressure is pre-matched at the factory, and it should display values directly after installation. No pairing is needed at this time. If values aren’t displayed, please pair them. To replace a sensor, unpair it first and then pair it with the new sensor.

Dash Cam Interface Description

Click to access the dash cam settings

1. Video Recording: Start/Pause
2. Take a Photo: Press to take a picture from both front and rear cameras simultaneously
3. Lock: Press to lock/unlock front and rear camera pictures
4. Recording: Press to toggle recording on/off
5. Perspective Switching: Press to switch between individual front/back camera display and picture-in-picture display
6. Playback : Press to return to the playback interface
7. Settings : Press to enter the menu
8. Homepage : Press to return to the previous page
9. Time : Display of time and date

Description of the Playback Interface

Press on the recording interface to access playback interface.

1. Play
2. Back
3. Lock
4. Play
5. Delete
6. Video Progress Bar
7. Regular Video Recording
8. Pictures
9. Locked Videos
10. Parking Monitoring Video
11. Video Files
12. Full Screen

Instructions for WIFI Connection

Click “APP Version” to enter the APP download page and scan the QR code to download the KYCAM2 APP.
A: Android System Connection Procedures

1. Find the name MT65BXXX in your phone’s WiFi settings and enter the password 12345678 to connect. After successful connection, the WiFi logo will change from white to green.
2. Some android mobile phones will prompt “no internet access in this network” or similar information, please select the option of “connect only this time” or “always connect”. (Note: Dash cam Wi-Fi is only used for the connection and operation of the host and the mobile phone APP, no internet connection).

iOS System Connection Procedures

1. Find the name MT65BXXX in your phone’s WiFi settings and enter the password 12345678 to connect. After successful connection, the WiFi logo will change from white to green.
2. Open KYCAM2-APP, press “Enter recorder”, the dash cam prompts to use GPS location, select “Allow when using APP” and “Allow to connect to local network”.

NOTE : The functions of the APP will be updated from time to time, and the detailed information will be based on the APP.

1. Press “Into Camera” to enter the home page to view and set up.
2. Album : Press to view downloaded videos and photos.
3. More : Settings-language- Time-Offline maps

Description of APP Keys

Description of APP Keys

Specifications

• Waterproof: IP65
• Screen Projection: Support Apple Carplay and Android auto Built-in Battery: Coin cell batteries
• Video Resolution : 1080P+1080P
• Quantities of Camera: 2(front and rear)
• Display: 5.0-inch IPS touchscreen
• Parking Monitor: Support 24 hours parking monitoring WiFi/APP Interface: Supported
• GPS track: Supported
• Video Format: TS
• Compression Format: H.264
• Memory Card Capacity: 32-256GB C10 TF Card
• Voltage: 12-30V to 5V 2A

QA (Questions and Answers)

1. Q: How to disconnect CarPlay or Android Auto?
   A: Simply turn off the WiFi or forget the Bluetooth device.

2. Q: How do I reconnect to CarPlay/Android Auto after manually disconnecting it?
   A: Reconnect to the dash cam through Bluetooth.

3. Q: How do I reconnect to CarPlay/Android Auto after restarting the dash cam?
   A: It will automatically reconnect when Bluetooth and WiFi are both enabled.

4. Q: How to make use of the App-Kycam2 when connected to CarPlay?
   A: Both can be operated simultaneously.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>