Guangzhou TXSA01 XM Antenna Owner’s Manual
- September 22, 2024
- GUANGZHOU
Table of Contents
Guangzhou TXSA01 XM Antenna
Product Information
Specifications
- Item: Antenna
- LNA Mechanical Environmental:
- Frequency Range
- Band Width
- Polarization
- Gain
- V.S.W.R
- Impedance
- Axial Ratio
- Dimension
- Gain Noise Figure
- Supply Voltage
- Current Consumption
- V.S.W.R Cable Connector
- Radome Material
- Mounting Method
- Operating Temperature
- Relative Humidity
- Ingress Protection
- Vibration Environmentally Friendly
Product Usage Instructions
Installation
- Locate a suitable mounting location for the XM antenna.
- Ensure the mounting surface is clean and dry.
- Mount the antenna using the provided mounting method.
Connection
- Connect the antenna cable to the appropriate connector on your XM receiver.
- Ensure a secure connection to prevent signal loss.
Optimization
- Position the antenna for optimal signal reception.
- Adjust the orientation if needed for better performance.
Frequently Asked Questions (FAQ)
Q: What should I do if I experience interference with my XM antenna?
A: If you experience interference, try the following steps:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
XM antenna
TXSA01
DIMENSIONS
SPECIFICATIONS
| Item | Specifications |
|---|---|
| Antenna | Frequency Range |
| Band Width | 25MHz |
| Polarization | LHCP |
| Gain | 3dBic |
| V.S.W.R | ＜1.5 |
| Impedance | 50Ω |
| Axial Ratio | 3dB（max） |
| Dimension | 25254mm |
| LNA | Gain |
| Noise Figure | ＜1.0dB |
| Supply Voltage | 3~5V DC |
| Current Consumption | ＜40mA@3.3V |
| V.S.W.R | ＜2.0 |
| Mechanical | Cable |
| Connector | SMA/MCX/FAKRA or others |
| Radome Material | ABS |
| Mounting Method | Magnet/Adhesive |
| Environmental | Operating Temperature |
| Relative Humidity | Up to 95% |
| Ingress Protection | IP67 |
| Vibration | 10 to 55Hz with 1.5mm amplitude 2hours |
| Environmentally Friendly | ROHS Compliant |
Radiation Pattern
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Please take attention that changes or modification not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>