GUANGZHOU YOUGUANG OPTOELECTRONICS CO LTD ADA03H4 43 Inch Outdoor Battery Powered LCD Signage User Manual

GUANGZHOU YOUGUANG OPTOELECTRONICS CO LTD ADA03H4 43 Inch Outdoor Battery

Powered LCD Signage

Product Usage Instructions

1. Assembling the Product
   Follow these steps to assemble the product correctly:

2. Connect part A to part B using the provided screws.

3. Insert component C into slot D until it clicks into place.

4. Attach the cover E by sliding it onto the main body and securing it with the latch.

5. Powering On the Product
   To power the product, press the ON/OFF button located on the front panel. Ensure the battery is properly inserted before powering on.

6. Product Settings Adjustment
   Use the control knobs to adjust the settings according to your preferences. Refer to the user manual for detailed instructions on setting adjustments.

7. Maintenance and Cleaning
   Regularly clean the product using a damp cloth and mild detergent. Avoid using abrasive cleaners that may damage the surface.

Frequently Asked Questions (FAQ):

Q: How do I replace the battery?
A: To replace the battery, follow these steps:

1. Turn off the product and disconnect it from the power source.
2. Locate the battery compartment and remove the old battery.
3. Insert a new compatible battery in the correct orientation.
4. Close the battery compartment securely before powering on the product.

Q: What should I do if the product malfunctions?
A: If you encounter any issues with the product, refer to the troubleshooting section in the user manual. If problems persist, contact customer support for assistance.

How to query the battery power and charge

1. As shown in the photo, the area is the battery power indicator. If you need to check the power range, please press the button, and the percentage of power will show.

2. When charging is required, plug the DC plug directly into the DC port to charge.
   Note: when the battery power is too low and needs to be charged, we recommend that the battery power should not be less than 10% to ensure the life of the battery.

3. When the product needs to be stored for a long time, the battery power shall not be less than 30%. When the storage time is more than 1 month, it is recommended to charge the battery every month and keep the power not be less than 30%, to keep the long life of the battery.

Product Information

Product feature

Battery-powered wheel 43-inch waterproof LCD is a Floor Standing LCD signage product with an elegant frame design, 43″ high-quality LCD screen, Signway control board, and CILICE power supply embedded inside, which is capable of having wireless, Ethernet, cloud platform, and USB program edit, playback for advertising, education, commercial and every kind of communication used at everywhere in the place you want. Light sensor: The screen brightness can be adjusted according to the ambient brightness (minimum 30%, maximum 100%, 256 levels of intelligent recognition and dimming) to save power and extend the use time of the whole machine.

Product Composition

1. Handle
2. Handle of the battery box
3. Wheels
4. Light sensor
5. LCD Screen
6. IR Indicator
7. Non-slip mat
8. Battery box
9. Lock
10. Battery indicator
11. Heat sink
12. Speaker
13. HDMI
14. USB port
15. Power switch
16. RJ45
17. AC power socket
18. Lock

Standard Accessories Quantity Table

Product Technical Data

Safety Warnings and Precautions

Based on the product design and LCD property, the following security works must be complied with in the device handling and use.

• Avoid high temperature and high moisture circumstances use: operating temperature of 0—400C; operating humidity
• Suitable operating time: 20 hours a day or less
• Suitable voltage input: 100—240v, excess voltage will cause damage to the device
• Keep away from strong electromagnetic circumstances: strong electromagnetic waves will cause damage to the device
• Be used in ventilated circumstances: well- ventilated environment would be better for the device use
• Avoid excessive vibration, heavy drop, and severe impact: any heavy vibration, drop, and impact will cause damage to the device
• Do not replace or modify product parts by yourself: we will not be responsible for any product problems of the device caused by self-adjustment.
• To have regular cleaning work: regular cleaning work is good for the device’s operation

Product Ingress Protection
The product is IP65 grade (INGRESS PROTECTION)

• 6-Prevent dust from entering
• 5-The anti-spray type machine is directly exposed to the water jet without harmful effects

Precautions:

• Please make sure that all wiring ports are closed when the product is used outdoors.
• Do not use this product in bad weather conditions, such as storms, sandstorms, etc.

Lithium Batteries Disclaimer of Liability
Guangzhou You Guang Optoelectronics Co., Ltd is not responsible for any direct, indirect, special, or consequential damages and personal injuries, including that to life, and health, resulting from the customer’s application and use of Guangzhou You Guaung products. You, the customer, assume full and unlimited responsibility for all customer Battery applications and uses. Your purchase of this product constitutes your agreement to hereafter assume full and total responsibility for your subsequent utilization of the Battery and you agree to defend, protect, save harmless, and indemnify Guangzhou You Guang., its officers, and employees relative to your potential use and misuse of this product. By purchasing or using a Guangzhou You Guang product you agree to the above terms.

IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS
As Lithium batteries are volatile, please read these safety instructions and warnings before using or charging your batteries. Failure to do so may result in fire, personal injury, and property damage.

General Guidelines and Warnings

• Battery charge and discharge rates are given as a multiplier of the capacity. For example, a 3300 mAh (mili Amp-hour) battery with a 20C rating, the maximum continuous discharge rate is:
• Store and charge in a fireproof container; never in your model!
• Never short a battery by cutting both wire leads simultaneously, contact with a conductive object, or any other means. If you accidentally short the wires, the battery must be placed in a safe area for observation as described above.
• In the event of damage (from a crash, etc), or swelling (ballooning); immediately cease use of the battery and observe it in a safe place for at least 30 minutes. Continuing to use a battery that has any physical damage, or has begun to swell may result in fire, injury, or damage.
• We recommend a 3-5C max average discharge rate for breaking in new packs. Also be extremely careful not to over-discharge new packs (Packs should NEVER be over-discharged at any time, but over-discharging on the first flight will result in permanent damage to the battery).
• Never store or charge a battery pack inside a vehicle (especially in extreme temperatures).
• Store battery at room temperature between 40 and 80 OF (4 to 27 0 C) for best results
• Do not expose the battery pack to direct sunlight (heat) for extended periods.

Charging of Battery Packs

• Let the Battery Pack cool down to ambient temperature before charging. Only charge batteries when the ambient, battery, and charger temperatures are between 32 and 1130F (0 to 450C)
• Before connecting to the charger, make a visual inspection of the pack. Look for any damaged leads, connectors, broken shrink, swelling of cells, or other irregularities. Do not use it if you find any of the above issues with your pack.
• Do not charge battery packs in series. Charge each battery pack individually. Failure to do so may result in incorrect battery recognition and charging functions.
• Use specific Balance Chargers only. Always check that all charger settings have been appropriately set for your specific battery pack.
• Always use balance charging. Do not charge without balancing; this will cause the cell voltages to become unbalanced; which may result in overcharging and damaging cells
• Never charge batteries unattended or overnight. When charging batteries you should always remain in constant observation to monitor the charging process and react to potential problems that may occur.
• Do not charge batteries above 25Volts/pack. Overcharged batteries are extremely dangerous.

Discharging (Use) of Battery Packs

• Do not discharge the batteries at a rate greater than they are rated for.
• Do not discharge batteries more than 80% of their capacity.
• Do not discharge batteries to below 3 volts per cell. Doing so will decrease the battery’s lifespan.
• Discharge only when the battery and ambient temperatures are between 32 and 140’F (0 to 600C).
• As a general guideline, a battery should never become so hot you cannot hold it tightly in your hand.

Battery Disposal

• Batteries that lose 20% of their capacity must be removed from service.
• Before recycling, discharge the battery to 3V/Cell, make sure output wires are insulated, and then wrap the battery in a bag.
• Do not dispose of batteries in the trash! Take your battery to an approved battery recycling facility.

Product installation

Terminology of the product:

• The product: The whole product, including hardware and software of the front-end display device and back-end content software platform.
• The device: front-end display device which is shown on the Icover page of this manual.
• G TV: the display software applied on the front-end device management. Please refer to the “Signway DS Player Software_Android_Manual_V1.0 140609” PDF for the details.
• CDMS: the content management software applied on the back-end content edit, program produce, program publish.. etc. management. Please refer to “Dthe digital Signage CDMS Manual V4.6.20” PDF for the details.
• Android: Android is an operating system based on a modified version of the Linux kernel and other open-source software, designed primarily for digital devices. The product was developed based on the Android system.

Set up the product and the way to access

• Open the device’s back bracket, place it on a flat floor, and connect the AC to the power
• Turn on the power switch, make sure the LCD is on and the IR indicator, blue light on the surface, is on as well.
• Make sure the mouse or the remote control works well ( we recommend using the mouse which is a more efficient tool )
  • mouse: connect a wire or wireless mouse by using the USB port on the back of the device

Remote Control

Two ways to configure the device

Through the GTV Home page ( also called the OSD menu)
When the device is turned on, the system will enter into the GTV home page at once, and playback mode is active automatically, then if there is a program ready for playback, either sourced from ROM or USB storage, the program will playback immediately. But if there is no program ready, the GTV home page below will stand still for further action.

At this moment, you can press the button on the remote control or click, you can press on the upper left corner of the G TV home page and enter into the system setting page as below, then you can go on to language, work mode, network, time…configuration.

Through the Android home page:
When the device is playing, press to return to the G TV home page. At that moment, press sequentially to act exiting GTV and entering the Android home page. Afterward, you can click on the page or click the Android menu first and then click on the Android menu page to enter into the Android setup page for device configuration. After configuration, click to come back to G TV and have playback again.

Certain settings are required before playback

Language:
English is the default language set in the factory, you can choose to select Simple Chinese or Japanese as you want by pressing .

Work mode:
there are two major categories of work mode: network and stand-alone

• Network: It means to upload programs to the device by the network, which is divided into wired(LAN), wireless(wifi), and 3G according to the upload path used.
• Stand-alone: It means uploading programs to the device by USB manually. You should click Work Mode and select “Single” and you have to activate USB on the System Setting page at the same time, then the device will recognize USB storage and upload the program inside when USB is inserted into the USB port.

Network setting:
When you select one of the network paths as your Work Mode, you must ensure that the network environment is properly set and available. If you have the correct setting, you will see the server address (web IP) shown on the page below.

Content Edit and Playback

Cloud CDMS server platform
We have set up a cloud CDMS server platform on the web to serve our customers. Please have your account and password and enter the website by using the computer. http://47.52.207.18:8088/cdmsA/index.jsp.

Content edit and produce program
After logging into the cloud CDMS platform, you can edit content, produce programs, create display plans, and publish programs to the devices on the platform. CDMS is a powerful platform for your displays, including images, text, video, audio, or a complex, please refer to the “Digital Signage CDMS_Manual_V4.6.20” PDF for the details of the operation.

Content upload and playback
As mentioned in 2.4.2 Work mode, there are two ways of uploading programs to the devices,

• Network: Be sure your device network is fully configured and functioning well, then you can publish programs to the devices easily.
• USB: In a stand-alone (single) scenario, you need to configure to activate USB first, as shown in >>”System Setting page-USB” on 2.4.2, download programs from the CDMS platform to your USB storage, and insert the USB into the USB port of the device, then the device will recognize the USB, upload program and playback automatically.

Product Warranty and Maintenance

Warranty Policy

• The product provides a one-year warranty starting from the ex-work delivery date under the premise of normal and reasonable use of the product.
• Any unauthorized replacement of parts and components and wiring changes are deemed to be a violation of normal and reasonable use, and we will not perform the warranty responsibility

Product Maintenance

• Regular cleaning on the product including dedusting of the surface and frame is required
• Following through with the use precautions mentioned in “1.4 Safety Warnings and Precautions” above is the most basic maintenance work.
• In case of a failure, please Inform the manufacturer and have maintenance operations by a qualified person under the manufacturer’s guidance.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>