Guangzhou Chengzhi Intelligent Machinery Technology Co Ltd MP10E Broadcast and Sound Pickup System User Manual
- October 30, 2023
- Guangzhou Chengzhi Intelligent Machinery Technology Co Ltd
Table of Contents
Guangzhou Chengzhi Intelligent Machinery Technology Co Ltd MP10E
Broadcast and Sound Pickup System
Disclaimer and Warning
- Thank you for purchasing CZI smart products. The content mentioned in this manual is related to your safety, legal rights, and responsibilities. Before using this product, please read this manual carefully to ensure that the product is set up correctly. Failure to follow the instructions and warnings in this manual may cause harm to you and others. The final interpretation right of this manual and all related documents belongs to CZI. In case of any updates, no separate notice will be given. For the latest product information, please visit our official website www.gzczzn.com.
- The maximum volume of MPlOE exceeds 107 dB, please do not turn to the maximum volume at close range, otherwise, the damage caused by it shall be borne by the user!
- Please install MPlOE according to the installation in the manual, and then power on the UAV for the broadcaster after assembly. This product does not support hot plugging at the moment!
- If it is windy, it is recommended to only insert one carbon tube to ensure safety. After installing the matrix microphone, please fly it carefully!
Introduction to MPlOE.
MPl0E is compatible with the DJI Mavic 3E and uses the PSDK link to achieve the same communication distance as the UAV. It combines the functions of a broadcaster, microphone, and police lights, creating a new era of aerial- ground communication for UAV.
MPlOE Parameter
Weigh| 140g
Main Engine size| 90mm80mm82mm
Length of microphone pole| 610mm
Power| 15W
Power supply| PSDK_TypeC (12V—l7.6V)
Speaker sound pressure| 107dB@lm
Effective broadcasting distance| 150m
Effective sound pick-up distance| 10m
Microphone signal-to-noise ratio| 67dB
Storage space| On-Body Memory (ROM): 16 GB
Real-time code stream| 8Kbps/ 16Kbps
Alarm lights| 3 red lights, 3 blue lights, power 2 W, light angle 60°
Operating temperature| -l0°C 40°C
Czi Sound App system support| Android7.0 and above/ IOS13 and above
Bluetooth handheld microphone sizel| 190mm60mm30mm
Bluetooth handheld microphone weight| 170g
Display color screen| 1.8 inches
Bluetooth| Bluetooth 4.2, Band 2.400-2.4835 GHz, Transmitting power (EIRP) <
10 dBm
Battery voltage| Voltage 3.7 V, Capacity 2600 mAh
Endurance| 3h
Charging| USB-C, SV 2A
Installation of MPlOE
Installation of Matrix Microphone
Align the white dot on the microphone pole connector with the notch and tighten the nut after plugging in the male and female ends. Inserting two carbon tubes can obtain a farther sound pick-up distance. If it is windy, it is recommended to only insert one carbon tube to ensure safety. After installing the matrix microphone, please fly it carefully!
The installation is as follow:
Installation of the Broadcaster
Align the Type C port with the PSDK interface on the UAV, and insert it into the port, then tighten the hand screws on both sides.
The installation is shown in the figure below:
Introduction to Czi Sound App
The Czi Sound App is a mobile phone software specifically developed by CZI for audio synthesis, algorithm processing, and Bluetooth uploading of songs. It can be downloaded from the mobile application store or CZI official website, and can be installed on mobile phones running Android 7.0 or above or IOS 13 or above. The specific functions of Smart sound are as follows:
-
Synthesize audio files (including TTS, recorded audio, mixed audio, text library, music library, scanning local audio on the phone), and upload them to the broadcaster through Bluetooth.
( Note: during the upload process, the corresponding audio enhancement and reverberation algorithm processing will be performed based on the broadcaster. Please be patient.) -
Statue monitoring and control of Broadcaster
-
Firmware pushing . Pushing firmware updates for the broadcaster and hand held microphone. (Only the new products after 2022 are supported.) The interface of Czi Sound App is as follow:
Introduction to the use of MSDK software of MPIOE remote controller Method of use:
- First, download the latest czi Pilot from CZI official website, and install it on the remote controller in DJI. After installing MPlOE, press the power of the UAV to turn on the remote controller.
- Set the joystick mode, return altitude, loss of communication behavior and return point in Pilot 2 software, turn off forward-looking obstacle avoidance, and then slide up from the bottom of the screen to close dji pilot software.
- Open the czi Pilot software, and the interface is as follows: Click the Bluetooth handheld microphone icon, search the serial number of the hand held microphone, and then connect HMlOE-X XX XX XX
Introduction to the use of Bluetooth handheld microphone
Switch on the hand held microphone with the knob in the upper right corner, and connect the hand held microphone with czi Pilot software.
* For more detailed usage, please watch the teaching video.
Firmware update
Czi Sound App will release the latest firmware to the Broadcaster and handheld microphone.
- For more detailed usage, please watch the teaching video.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hannful inte1ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be detem1ined by turning the equipment off and on, the user is encouraged to tly to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement The device can be used in portable exposure condition without restriction.
ChengZhi Support
CZI technical support www.gzczzn.com
Service Hotline: 400-008-8306
If you have any questions or suggestions regarding the manual
Please send email to: service@gzczzn.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>