Guangzhou V-Solution Telecommunication Technology HG323DAC 2GE+1POTS+WiFi Dual Mode HGU Installation Guide
- June 3, 2024
- Guangzhou V Solution Telecommunication Technology
Table of Contents
V-Solution Telecommunication Technology
HG323DAC 2GE+1POTS+WiFi Dual Mode HGU
Installation Guide
HG323DAC 2GE+1POTS+WiFi Dual Mode HGU
2GE+1POTS+WiFi(dual band) Dual Mode HGU
HG323DAC
Quick Installation Guide
V2.0
Indicator and Interface Description
1.1 Product Picture
1.2 Application Chart
1.3 Panel Lights
| LED | Mark | Status | Description |
|---|---|---|---|
| Power | PWR | On | The device is powered up. |
| Off | The device is powered down. | ||
| Registration | PON | On | The device is registered to PON system. |
| Off | Device is not registered to PON system. | ||
| Blink | Device is registering. |
Optical
signal| LOS| Blink| Device does not receive optical signal.
Off| Device has received optical signal.
WAN| WAN| On| WAN connection is up.
Blink| Data passing WAN connection.
Off| WAN connection is down.
Ethernet| LAN1
LAN2| On| Port is connected properly.
Off| Port connection exception or not connected.
Blink| Port is sending or/and receiving data.
Wireless| 2.4G
5G| On| WiFi is turned on.
Off| Device is power off or WiFi is turned off.
Blink| WiFi turned on and with ongoing data transmission.
Pots| PHONE| On| Device has registered to soft-switch, but without ongoing
data transmission.
Off| Device is power off or not registered to soft-switch.
Blink| The port is with ongoing data transmission.
Table 1 Panel Lights
1.4 Interface/button Panel
| Name | Function |
|---|---|
| PON | Connect to OLT by SC type fiber connector, single mode optical fiber |
cable.
FXS| Connect the telephone with FXS port by telephone wire.
LAN1/2| Connect PC or other devices with Ethernet port by Cat5 cable, RJ-45
connector.
DC 12V| Connect with power adapter.
ON/OFF| Power supply switch.
RST| 1.Press RST button over 10 seconds, onu restores factory default and
reboot.
2.Press RST button quickly, onu reboots.
Pair| Press down WiFi pair button to begin pairing.
WiFi| Press down WiFi button to enable/disable WiFi function.
Table 2: Interface/button Panel
Packing List
| Contents | Quantity | Contents | Quantity |
|---|---|---|---|
| Dual Mode HGU | 1 pcs | Power adapter | 1 pcs |
| Installation Guide | 1 pcs | Network cable | 1 pcs |
Certification
Hardware Installation
Installation Environment Requirements
ONU equipment must be installed in the interior, and to ensure the following
conditions:
- Confirmation at the ONU installation at sufficient space to facilitate cooling machine.
- ONU suitable operating temperature of -5 ~ 55 , humidity 10% to 90%.
- Device workplace should avoid radio transmitters, radar stations, and high-frequency interference from power equipment.
Equipment Installation
1. Installed on the desktop
Place the ONU on a clean bench, this installation is relatively simple, you
can observe the following operation:
- Ensure the smooth workbench.
- Around the device enough space for heat dissipation.
- Do not place objects on the device.
2. Mounted on the wall
- Observation ONU equipment chassis two cruciform recess, in accordance with the position of the groove, installed two screws in the wall.
- The original selected two mounting screws gently snap into recesses aligned.
- Slowly let go, so that the device under the support of the screw hanging on the wall.
3. Connect fiber, network cable and power adapter to the corresponding interfaces, and turn on the power of product.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>