Treevol Furniture WHFP003 Dresser Maldus White Finish Installation Guide
- September 12, 2024
- Treevol Furniture
Table of Contents
Treevol Furniture WHFP003 Dresser Maldus White Finish
Specifications:
- Product: Three Drawer Dresser
- Tools Needed: Phillips head screwdriver, Flat head screwdriver, Hammer
- Additional Tools: Flat, smooth surface, Electric screwdriver (optional)
- Hardware Included: Wood dowels, Spreading bolt, Minifix cam, Cover caps, Drywall screws, Back panel guide, Flat head screws, Slides + screws, Nail-on glide, Back Panel Support, Wall anchor + screw
Product Usage Instructions
What will you need?
Hi! My name is Armando, and I’ll be with you while you assemble this
cabinet.
Make sure you have the following tools ready:
- Phillips head screwdriver
- Flat head screwdriver
- Hammer
- A flat, smooth surface (cardboard of the box or a rug)
- Electric screwdriver (optional but can make the work easier)
Where should you start?
Ensure that you have all the necessary panels and hardware components as
listed in the manual before starting the assembly.
What’s in the hardware bag?
The hardware bag contains essential components for assembly such as wood
dowels, spreading bolts, Minifix cams, cover caps, drywall screws, back panel
guide, flat head screws, slides + screws, nail-on glide, back panel support,
and wall anchor + screw. Keep all components safe and organized.
How do the dowels and Minifix system work?
Wood dowels are used to join panels together by inserting them into
designated holes and gently hitting them until fully inserted. The Minifix
system consists of spreading bolts and Minifix cams. Align the components
correctly with the arrows and secure the joint.
Assembly Steps:
Weight Capacity:
Ensure not to exceed the recommended weight capacity of your cabinet. Refer
to the manual for weight limits.
Cabinet Maintenance:
Follow the provided recommendations for caring for your cabinet to ensure
its longevity and durability.
FAQ:
- Q: How long does it take to assemble the dresser?
A: The assembly time varies depending on your familiarity with assembling furniture and following instructions. On average, it may take around 1-2 hours.
It’s much better if you get some company for this!
What will you need?
A flat, smooth surface. You can use the cardboard of the box or a rug.
An electric screwdriver isn’t necessary, but it can make the work much easier 🙂
Where should you start?
This is so IMPORTANT!
Over the next few pages is the panel and hardware content for this cabinet.
Please make sure that the quantity of each one is correct, and that everything
is in good shape.
(When the cabinet is already assembled there’s no warranty for this)
Panel quantity
| A – x1 | B – x1 | C – x1 | D – x2 |
|---|---|---|---|
| E – x2 | F – x1 | G – x3 | H – x3 |
| I – x3 | J – x3 | K – x1 | L – x1 |
| M – x1 | N – x1 | O – x3 | P – x2 |
What’s in the hardware bag?
Be careful!, try not to lose anything from this bag, its content is necessary for assembling your cabinet.
Be careful!, try not to lose anything from this bag, its content is
necessary for assembling your cabinet.
this is so important too!
Everytime you’re using one of these connectors during the assembly, you
should follow these same steps.
Wood dowels
They are little wooden cylinders.
- Put in the dowel inside the indicated hole and softly hit it until it’s fully inside.
- When joining two panels together, don’t forget to gently hit the panels to adjust the joint.
Minifix system
It’s a joint compound of two parts: a spreading bolt and a Minifix cam.
-
This is a Minifix cam.
It has a little arrow on its upper surface. -
You should insert these cams with the little arrow pointing towards the drilling on the panel’s edge (shown on the left).
-
This is a spreading bolt.
You should put it with the black plastic part facing down. -
After joining two panels together you should turn the cams 180° with a phillips head screwdriver to adjust and secure the joint.
Let’s start assembling!
You can see the last page of this manual to have a full look of the panels of this cabinet.
Drawer slides installation (apply for steps 5 and 8)
To begin, you must take out the smaller part of the slide, pushing down the black plastic part shown below:
Fix your cabinet to the wall
- On the wall, measure and mark the points shown below.
- Drill on the markings with a 5/16″ drill bit.
- Insert the wall anchors inside the drillings.
- Place the cabinet and secure it with the screws.
After adjusting all the Minifix cams, cover them up with the cover caps.
After finishing the assembly, lift off al the adhesive letters.
How much weight does my cabinet resist?
Congratulations!
It’s done
But don’t go yet!
There are some recommendations left for you to take care of your cabinet
correctly from now on.
SUPER IMPORTANT!
We suggest fixing the cabinet to the wall, so we can avoid the cabinet tipping
and harming anyone.
Be specially careful with the kids.
Taking care of your cabinet:
- Do not paint the cabinet.
- The cabinet it’s exclusively for indoor spaces. Do not expose it to the direct sun.
- Clean the metallic hardware with a dry cloth.
- DO NOT overload the cabinet (see suggested loads)
- Do not hit or hammer the cabinet (only when indicated here).
- Clean it with thinner, a soft soap solution or simply a damp cloth.
- Don’t drag the cabinet, lift it up with other people.
- Avoid direct contact with water, fire or exposing it to high heat.
Cabinet panels
WARRANTY POLICY
Furniture has a 3 year warranty coverage in wooden parts and 1 year warranty coverage in hardware pieces since its manufacturing date, which you can see in the lot number printed on the product box and the assembly instructions leaflet. Warranty covers materials and workmanship imperfections which impair the assembly or correct functioning of the cabinet. This warranty is not valid if the defects or imperfections are caused by the incorrect following of the assembly instructions, warnings and recommendations, misuse, intentional damage, fire or flood, or after modifications or any kind of alteration, or repaired by someone not authorized, when it´s been assembled 3 months after the date of purchase. These defects MUST be reported before the warranty coverage period ends. Once the product has been assembled, the company will not be responsible for defective and/or damaged parts.
This warranty is ONLY valid for the ORIGINAL PURCHASER, it doesn’t apply if the product has been resold, rented, etc. Furniture will take no liability for incidental or consequential damages caused to or by the product (This may not apply in your state). To make this warranty valid you must write to our customer service email describing the product defect, lot number and submitting your sales reciept or proof of purchase, or contact us at our customer service line. Replaced parts will be under the product´s original warranty coverage period. Damaged parts will become property of the company. There are no other warranties applicable to this product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>