Treevol Furniture WHFP079 Crestone 4 Tier Open Shelving Installation Guide
- September 6, 2024
- Treevol Furniture
Table of Contents
Treevol Furniture WHFP079 Crestone 4 Tier Open Shelving
Specifications
- Dimensions: 20.86 x 4.92 x 17.6 inches
- Weight Capacity: 17.6 pounds
FAQs
How much weight can my cabinet hold?
The cabinet is designed to withstand up to 17.6 pounds of weight.
Why should I fix the cabinet to the wall?
For safety reasons, it’s recommended to secure the cabinet to the wall to prevent tipping, especially around children.
TOOLS
What will you need?
- A flat, smooth surface. You can use the cardboard of the box or a rug.
- An electric screwdriver isn’t necessary, but it can make the work much easier 🙂
GET START
Where should you start?
This is so IMPORTANT!
Over the next few pages i the panel and hardware content for this cabinet. Please make sure that the quantity of each one is correct, and that everything is in good shape. (When the cabinet is already assembled there’s no warranty for this)
Panel quantity
| A – x4 | B – x2 | C – x2 | D – x1 |
|---|
hardware bag
What’s in the hardware bag?
this is so important too!
Every time you’re using one of these connectors during the assembly, you should follow these same steps.
Wood dowels
They are little wooden cylinders
- Put in the dowel inside the indicated hole and softly hit it until it’s fully inside.
- When joining two panels together, don’t forget to gently hit the panels to adjust the joint.
Minifix system
It’s a joint compound of two parts: a spreading bolt and a Minifix cam.
- This is a Minifix cam. It has a little arrow on its upper surface.
- You should insert these cams with the little arrow pointing toward the drilling on the panel’s edge (shown on the left).
- This is a spreading bolt. You should put it with the black plastic part facing down.
- After joining two panels together you should turn the cams 180° with a Phillips head screwdriver to adjust and secure the joint
ASSEMBLY INSTRUCTIONS
Let’s start assembling!
You can see the last page of this manual to have a full look of the panels of this cabinet.
WALL ANCHOR
Fix your cabinet to the wall
- You must drill the bottoms guided by the holes in the structures wiht a 3/16″ drill bit
- On the wall, measure and mark the points shown below.
- Drill on the markings with a 5/16″ drill bit.
- Insert the wall anchors inside the drillings.
- Place the cabinet and secure it with the screws.
Dimensions
- After adjusting all the Minifix cams, cover them up with the cover caps.
- After finishing the assembly, lift off al the adhesive letters.
How much weight does my cabinet resist?
weight in pounds
Congratulations! It’s done
But don’t go yet! There are some recommendations left for you to take care of your cabinet correctly
SUPER IMPORTANT
We suggest fixing the cabinet to the wall, so we can avoid the cabinet tipping and harming anyone. Be especially careful with the kids.
Taking care of your cabinet:
- Do not paint the cabinet.
- The cabinet it’s exclusively for indoor spaces. Do not expose it to the direct sun.
- Clean the metallic hardware with a dry cloth.
- DO NOT overload the cabinet (see suggested loads)
- Do not hit or hammer the cabinet (only when indicated here)
- Clean it with thinner, a soft soap solution or simply a damp cloth.
- Don’t drag the cabinet, lift it up with other people.
- Avoid direct contact with water, fire, or exposing it to high heat
Cabinet panels
WARRANTY POLICY
Furniture has a 1-year warranty coverage in wooden parts and hardware pieces since its manufacturing date, which you can see in the lot number printed on the product box and the assembly instructions leaflet. Warranty covers materials and workmanship imperfections that impair the assembly or correct functioning of the cabinet. This warranty is not valid if the defects or imperfections are caused by the incorrect following of the assembly instructions, warnings, and recommendations, misuse, intentional damage, fire or flood, or after modifications or any kind of alteration, or repaired by someone not authorized when it´s been assembled 3 months after the date of purchase. These defects MUST be reported before the warranty coverage period ends. Once the product has been assembled, the company will not be responsible for defective and/or damaged parts. This warranty is ONLY valid for the ORIGINAL purchase, it doesn’t apply if the product has been resold, rented, etc. Furniture will take no liability for incidental or consequential damages caused to or by the product (This may not apply in your state). To make this warranty valid you must write to our customer service email describing the product defect, and lot number and submit your sales receipt or proof of purchase, or contact us at our customer service line. Replaced parts will be under the product´s original warranty coverage period. Damaged parts will become the property of the company. There are no other warranties applicable to this product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>