Pinwei DT257W-H Wireless HDMI Extender Transmitter and Receiver User Manual
- August 21, 2024
- Pinwei
Table of Contents
Wireless HDMI Extender
Transmitter & Receiver
User Manual
Connection Diagram
Please refer to the instructions to connect
Connection Steps
Combination of receiver and transmitter, The product has been paired out of the factory. plug and play.
-
Connect the HDMI port of the signal Receiver (RX) to the HDMlinput port of your monitor or TV, Then connect USB-C cable withPower Port, And plug power cable into the power adapter.
(Currentand voltage greater than 5V/1A); The display enters the blue connection status screen; -
Plug power cable into the power adapter and connect the signal transmitter(TX) to the computer or other device with HDMI video output function; (Current and voltage greater than 5V/1A);
-
Transmitter (TX) the indicator light changes from flashing tosteady ON,Wait 2 seconds for connection to complete.
Enjoying
the convenience of wireless HDMI.
If you need any help, have any questions or complaints about the product,
please do not disassemble the machine by yourself, contact us immediately!
*(Note):
Please refer to user manual for connection to achieve ideal effect.
Please ensure that the transmitter (signal source side) and receiver (monitor
side) are adequately powered, If power supply is insufficient or unavailable,
the connection may fail.Need to unplug devices and power cables,Plug the
charging cable back in,Plug it into the device to connect.
Pairing Settings
If during use, the connection fails due to improper operation or other circumstances, the connection fails, or the connection interface cannot be entered. The device needs to be restored as follows:
LED light staatus
Flashing| Pairing
Steady ON| Completed
- Connect the HD port of the signal receiver (RX) to the HD input port of your monitor or TV, Then connect USB-C cable with Power Port, And plug power cable into the power adapter. (Current and voltage greater than 5V/1A)
- Plug the receiver device into HD port corresponding to the monitor until you enter the blue startup interface.Press function button for about 5S,The indicator light changes from flashing to steady ON, Screen display Ready to Pair
- Connect the signal transmitter (TX) to the computer or other device with HDMI video output function,Press function button for about 5S, The indicator light changes from flashing to steady ON,The screen interface displays Pairing,Wait 2-10 seconds for connection to complete.
*(Note): 1 Rx max can paire with 5 TX.
Common problem
Q:What HDMI version of this product support? What is the Max resolution supported?
A:This product support HDMI1.3 Version,Max resolution is 1920*1080P@60Hz.
Q:What are the functions of the product’s function buttons?
A:Press the transmitter function button to disconnect or reconnect.
Q: Why the connection failed, or the connection was interrupted?
1.Please check the receiver and transmitter are plugged into wrong HD port each other. 2.Please check if the power cord is plugged in. The current must not be less than 5V/1A. 3.Please make sure there are not too many other wireless products around the product to avoid excessive wireless interference that may cause the product to fail to work properly. 4.If the above issuse occurs, please unplug the product together with power cable, re-insert the corresponding device, and repeat the connection steps.
A:Q:Maximum transmission distance and delay impact?
A:The product Max transmission distance is 30m/98 feet,Latency is less than 0.1S.During use, The stable power supply of no less than 5V/1A is required to ensure the consistency of signal transmission.
Q:Why is the product not compatible with my phone?
A:This product supports computers, laptops, TV boxes, cameras and other devices with HDMI interfaces. For smartphones, it only supports some models.
Q:Why do images appear delayed or stuck?
If the above answers do not solve the problem, please contact the after-sales team. 24 hours dedicated service to you.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Specific Absorption Rate (SAR) information:
This HDMI Wireless extender meets the government’s requirements for
exposure to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through periodic and
thorough evaluation of scientific studies. The standards include a substantial
safety margin designed to assure the safety of all persons regardless of age
or health. FCC RF Exposure Information and Statement the SAR limit of USA
(FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: HDMI
Wireless extender has also been tested against this SAR limit. This device was
tested for typical body-worn operations with the back of the HDMI Wireless
extender kept 5mm from the body. To maintain compliance with FCC RF exposure
requirements, use accessories that maintain an 5mm separation distance between
the user’s body and the back of the HDMI Wireless extender. The use of belt
clips, holsters and similar accessories should not contain metallic components
in its assembly. The use of accessories that do not satisfy these requirements
may not comply with FCC RF exposure requirements, and should be avoided.