kasa smart KS220MUS1.0 Smart WiFi Dimmer Switch User Guide
- June 12, 2024
- Kasa Smart
Table of Contents
kasa smart KS220MUS1.0 Smart WiFi Dimmer Switch
Product Information
The Kasa Smart Dimmer Switch is a smart home device that features built-in motion and ambient light sensors. These sensors work together to provide hands-free control of your lights, automatically turning them on and dimming them as needed. This not only saves you effort but also helps reduce electricity bills.
Product Introduction
Built-in motion and ambient light sensors work together to realize hands-free control. Kasa smart dimmer switch turns on and dims the lights automatically, saving you effort and electricity bills.
Wire Your Switch
-
Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the Ground and Neutral wires.
- Ground: Usually green or copper.
- Neutral: Usually white and not connected to a dumb switch. Line: Usually black and coming from the circuit breaker. Load: Usually black. One end is connected to the light. If you are unsure, consult a qualified electrician.
-
Disconnect the wires from the old switch.
-
Identify Line and Load wires.
-
Turn on the circuit breaker. Use a voltage detector to identify the energized wire (Line wire).
WARNING: Take care to avoid electric shocks. -
Turn off the circuit breaker. Label the Line and Load wires.
-
Connect the wires to the smart dimmer switch as shown below.
-
Line up the switch with the mounting holes. Secure it with screws.
-
Attach the wallplate. Then the wiring is finished.
Flip the page over to complete setup.
Set Up Your Switch
STEP: DOWNLOAD APP
Get the Kasa Smart app from the App Store or Google Play.
STEP 2 SET UP
Tap the button in the app and select Smart Switches. Then follow the step-
by-step app instructions to set up your smart dimmer switch.
Appearance
Button Explanations
| Decrease or increase the brightness.
---|---
Reset
| Press and hold for about 5s to reset Wi-Fi while keeping other settings.
Press and hold for about 10s to restore your switch to factory default settings.
Restart| Press to restart your switch.
LED Status
| Flashing amber & green | Ready for setup. |
|---|---|
| Flashing green | Connecting to Wi-Fi. |
| Stay green for 30s | Connected to Wi-Fi. |
| Solid red | Disconnected from Wi-Fi. |
| Flashing amber | Device resetting. |
| White | Light fixture is off. |
Specifications
- Rating: 120V~ 60Hz
- Load: 300W Incandescent, 150W LED
- Operating temperature: 0~40°C
- Method of mounting included: Independently mounted (Vertically position only)
- Pollution Degree: 2
- Rated Impulse Voltage: 2500 V
- Software Class: A
- NEMA Type: 1
CAUTION
High Voltage-Disconnect power supply before servicing
Safety Notice
Before installing, servicing or removing the switch, read and follow all safety precautions including the following:
- CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
- The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements, or are uncomfortable performing the installation, consult a qualified electrician.
- Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
- Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).
- Tighten terminal screws to 13 lbf-in.
Images may differ from your actual product.
Need some help?
- Visit www.tp-link.com/support
- For technical support, user guides, FAQs, warranty & more
7106509394 REV1.1.0 ©2022 TP-Link
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>