KEMIMOTO Midnight Series Soundbar Audio System User Manual
- September 6, 2024
- KEMIMOTO
Table of Contents
KEMIMOTO Midnight Series Soundbar Audio System
CAUTION
- Read this instruction carefully before installation applied
- Keep the instruction in a safe place in case you need it in the future
- Refer to qualified people or contact us if you need to disassemble or repair the device
- Don’t merge the device into water, it may cause harm to the device.
- Always check the polarity of the power before installation to avoid harm to the device or your battery pack.
Enjoy the music at the proper volume level
- Listening to music at high volume might cause hearing damage, the sound pressure level scale of this product might cause a loss of hearing to normal people, even if just a short period of hearing. Sound is kind of deceptive, your feeling of a “proper” sound level will change as time goes by, and the “proper” sound level might actually be louder than what you recognized. So please set the volume to a secure level before you adapt to an inappropriate sound pressure and don’t change it easily.
Safe volume setting
- Set the volume to a low level at the beginning
- Press the button to increase the volume until you get a clear image of sound and proper bass without distortion. The
proper time of the hearing
- A long period of hearing, even if it’s under safe volume, is not advised either. Hearing damage will occur with long time use Proper use of the device and adequate rest time is recommended
My wireless soundbar
Dynamic Bass
An RMS power 60 watts bass channel is set up in the soundbar system which delivers profound & dynamic bass
Sync for power overlap
More power requests? Overlap the power by 2 soundbars with Kemimoto’s audio sync technology, sync with not just audio.
OA & DSP chipset inside
Advanced pre-OA (Operation Amplifier) chipset and professional audio DSP (Digital Signal Processor) are applied to guarantee the noise-free pre- signals, the DRC (Dynamic Range Control) technology delivers a distortion-free audio output even in peak power.
Spectrum beating lights
The 32-bit lighting control MCU has a super fast master frequency of up to 72MHz, the LED light strip reacts to every beat of music precisely, and we make the audio be visible. hundreds of spectrum cues available in Kemimoto light control APP
Various Scenario for installation
We provide various options for mounting, hanging/sitting on bars, and flat surfaces mounting/hanging, It’s not only ATV/UTV/GOLF carts, but also the mower, kayaks, yachts, RVs, they are all under design consideration.
Packing list
Dimension
Quick installation
- Screw up the bottom half of the clamp to the thread holes on the speaker housing via hexagon M6*10 bolts in the accessory pack. there are 2 clamps that need to be mounted, make sure they are tightened enough before you carry on to the next step
- Screw up the 2 halves of the clamp by using the hexag n M6*50 bolts in the accessory pack. make slight adjustments to the speaker’s face direction, then tighten them up. Plug in the powered cord with SAE connector
- Find an open place on the bar of your vehicle, and put the top half of the clamp onto the bar. then lift your soundbar up for docking Don’t forget the rubber friction pads, which are important to keep the speaker steady in driving.
- Turn on the soundbar, enjoy the trip
- Flip the soundbar speaker facing the downside, and connect the shaft parts together with the L-shaped brackets via hexagon M6*10 bolts in the accessory pack. there are 2shafts need to be installed need to be mounted, make sure they are tightened enough before you carry on to the next step
- Screw up the 2 halves of the clamp by using the hexagon M6*50 bolts in the accessory pack. make slight adjustments of the speaker’s face direction, then tight them up. Plug in the powered cord with SAE connector
- Find an open place on the bar of your vehicle, and place the top half of the clamp around the bar. then place your soundbar down for docking. Don’t forget the rubber friction pads, which are important to keep the speaker steady while driving.
- Turn on the soundbar, enjoy the trip
Control panel
- Power On/Off, Press and hold to turn on/off the speaker
- 8a Previous soundtrack
- Play & pause the music
- Volume decrease
- Trigger/clear the sync paring
- LED button, Press and hold to turn on/off the LED strips, click to circle the 19 sequences
- Next sound track
- Volume increase
- Audio sources selection, cycles in BT/AUX/USB mode
- Sound source indicator:
- Blue: Blue Tooth mode
- Green: Auxiliary input mode
- Red: USB mode
- Purple: TWS mode
- 2 x 3.5″ mid-range driver 12)
- 2 x 1″ titanium dome tweeter
- 2 x 4″ woofer driver 14
- 2 x dream color LED strip
- 2 x dream color LED halo ring
- 24″ dream color LED strip
- 24″ double-row dream color LED strip
- USB port, accept USB thumb and decode the music stored, as well it provides DC5V charging power for phone, maximumly 2A@5V
- Auxiliary input port
- DC12V output port for external appliance(eg. another speaker or lights)
- DC12V input port (eg. car battery)
- Auxiliary output port(eg. subwoofer)
Remote Control
- Speaker power On/Off.
- Previous soundtrack
- Play/pause
- Next sound track
- Mode: Sound sources select
- Scene: Light scenes select
- Volume decrease
- Volume increase
- Beat: LED light cues follow the music rhyme
- Demo: LED light auto cycle plays all the cues
- Dome: LED light goes to all white
- LED Light power On/OFF
- Mode+: LED light mode select
- Cue+: LED cues select under certain Mode
- Bright+:LED light brightness increase
- Speed+:LED light cues speed increase
- Mode-: LED light mode select
- Cue-: LED cues select under certain Mode
- Bright-:LED light brightness decrease
- Speed-:LED light cues speed decrease
- RED: LED light preset color
- Green: LED light preset color
- Blue: LED light preset color
- Purple: LED light preset color
NOTE : The remote control is an RF-based technology, there’s no direction required in operation, The power consumption is pretty low, you don’t need to change the battery frequently.Standby power consumption< 10ua Battery type: 1*CR2032
Bluetooth music
- Press and hold the power button on speaker or remote control to turn on the speaker you will hear the voice prompt ” Hello Kemimoto” and the LED indicator will show flashing blue that means Bluetooth is under standby waiting for connection
- Scan for the devices named “KM-Midnight 60/80″in your smartphone Bluetooth list, and click it to wait for the connection
- Once the Bluetooth is connected, the voice prompt”connected” will come out, and the LED will be static blue
- Run the playlist in the application on your smart phone, and control the speaker playback with previous/next/play/past volume+/- on the front panel or remote control.
USB music
- Insert the USB thumb, with MP3/WMA format music stored, into the USB acceptance at the back of the connecting panel, The mode will automatically turn to USB mode, and start playing USB music after voice prompt”USB mode”
- Press the SRC button on the speaker panel or remote control cycle and select the speaker mode until you hear the voice prompt ” Hello Kemimoto” and the LED indicator will show static red that means the system is under USB mode
- Control the speaker USB music playback with previous/next/play/pause volume+/- on the front panel or remote control
Note:
- The system supports a hot swap of USB thumb, you are allowed to plug out/ in the USB during the working status.
- Make sure there (is ) is at least one piece of music file stored in the USB thumb, or the decode might not recognize the USB.
- The system will kick into USB mode directly once the USB thumb is inserted and successfully recognized.
- The USB port can provide 5V power to mobile phones or other appliance charging, with a maximum 2A output current.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>