KEMIMOTO B0106-08901BK RGB LED Rear View Center Mirror with Bluetooth Instruction Manual
- June 5, 2024
- KEMIMOTO
Table of Contents
Installation Tips
SKU ► B0106-08901BK
Complete journey of dreams
Designed by Kem moto Group Web: www.kemimoto.com
BEFORE YOU BEGIN
- Read these instructions and the deck to be sure all parts and tools are accounted for.
- Please retain these nostalgia instructions for future reference and parts ordering information_
IMPORTANT
- Please read the installation instructions carefully before you start.
- If the vehicle is clean and free of other debris, it will be easy to install.
- For your safety and to ensure a satisfactory Installation. please complete all the installation steps in the order shown below.
PRODUCT INFORMATION:
1. Rubber Pad
2. Pipe Clamp -1
3. T-type POM Sleeve
4. M6 Lock Nut
5. Y-type Bracket
6. Mirror Shell
7. EVA Explosion-proof Film
8. Convex Mirror R1300
9. Metal Frame
10. Pipe Clamp-2
11. M6 Metal Spring Washer
12. Mds L50 Hexagon Socket Screw
13. Plane Bearing
14. M6′ D15′ 1.5 Metal Gasket
15. M6’L30 Hexagon Socket Heac Screw
16. M31L12 Self-tat: gong Screw
17. Support
18. M5′ L20 Hexagon Socket Screw
19. RGB Light 20. M3’L
20 Hexagon Socket Screw
21. Reading light (Emergency light)
22. POM Ball Head
23. Power Cord
24. Bluetooth Remote Control
25. Power Extension Cad
26. Bluetooth Controller| x1
x1
x2
x2
x1
x1
x1
x1
x1
x1
x1
x1
x1
x2
x2
x8
x1
x3
x1
x2
x1
x1
x1
x1
x1
x1
---|---
INSTALLATION TIPS:
STEP 1
Step 1
Place rubber pad Mat roll bar. Instal pipe ciarnp-1 [2] and c ce. damp110]
with spring washer [11] and screw 112].
STEP 2
Step 2
Conned the mirror, extension cord 125) and Bluetooth controller [261 Then
attach the Bluetooth controller (28] b relay:+) and vehcle power supply;-;
WIRING DIAGRAM:
NOTE: -The wet ‘1, contrail: relay and tee shawl h tne DIAGRAM are not
Enchklea rn our prttluct – The battery is your ride power napes_
STEP3
Step 3
Scan the OR code on the controller 1241 download the control APR then open the
APP and connect to Bluetooth to control the RGB lights. Or you can control the
RGB fights with the Bluetooth remote control [24] directly.
FUNCTION DESCRIPTION:
-
It fits 1 5-2.0 rich diameter roll bar.
-
As ‘59.1 the mirror will not affect the installation of the windshield and the roof, which perfectly wives the problem that the three cannot coexist
-
As fig 2, the mirror can be so, Ing front and back at about 180° As fig 3, the mirror can be swung left and right at about 220°. Tighten the screw [‘5] aster finishing adjustment
NOTE Adding a through p pe can increase the Woe arm of the wrench. which makes it easier to tighten the screw [15]. -
As fig.4, about the reading light [21]: 1. The reading light [21] is powered by an independent battery and needs to be charged. (TYPE C Input – Charging time: 2.5 hours
– Full charge endurance: 3 hours
– The switch %I turn red when charging
– The rea light will go out when his charge
NOTE: If you find the reading light [21] can not It on after receiving our product, please charge it fully first. 2. Light colors Red, white and green. 3. Light mode Monochromatic constant light and monochromatic flashing
4. Light contrc:
– Short press the switch to light on
– Short press the synch to change light odor and light mode
– Long press the switch over 3 seconds to light off.
5. Battery: Capacity 850mAh; Voltage 4.2V; Current 500mA. USB Charging Cable: Voltage 5V. Current 1k -
As fg.5. the RGB light [19] can be controlled by APP or remote control [24].
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
B0106-D8901BK
Documents / Resources
|
KEMIMOTO B0106-08901BK RGB LED Rear View Center Mirror with
Bluetooth
[pdf] Instruction Manual
B0106-08901BK, B010608901BK, 2A449B0106-08901BK, 2A449B010608901BK, RGB LED
Rear View Center Mirror with Bluetooth, B0106-08901BK RGB LED Rear View Center
Mirror with Bluetooth
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>