KEMIMOTO B0117-03001BK UTV Sound Systems User Manual

June 13, 2024
KEMIMOTO

PRODUCT MANUAL
SKU: B0117-03001BK

BEFORE YOU BEGIN

  1. Please read the instructions carefully and verify that each item is in the list.
  2. Please retain these installation instructions for further reference and parts ordering information.

IMPORTANT

  1. Please read the installation instructions carefully before you start.
  2. If the vehicle is clean and free of other debris, it will be easy to install.
  3. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below.

RODUCT INFORMATION

KEMIMOTO B0117-03001BK UTV Sound Systems - PRODUCT

1 Speaker x2
2 Bracket x4
3 Throat Clamp x8
4 M6xL50 Screw x24
5 M6 Spring Washer x16
6 M6 Flat Washer x16
7 M6 Nut x8
8 Amplifier Unit x1
9 Power Extender x1
10 Control Panel x1
11 USB/AUX Extender x1
12 Signal Extender x2
13 Cable Tie x20

Estimated installation tim
50 minutes
Required tools : (to be prepared by oneself)

INSTALLATION TIPS

KEMIMOTO B0117-03001BK UTV Sound Systems - speaker1Pre-assemble the speaker [1] and bracket [2] together with eight screws [4], washers [5]and flat washers [6].
KEMIMOTO B0117-03001BK UTV Sound Systems - speaker2Fit the throat clamp onto the front and rear crossbeams of the vehicle’s roof roll cage.KEMIMOTO B0117-03001BK UTV Sound Systems -
speaker3Adjust the position of support bracket [2] according to the distance of the roll bar, tighten the screw on the back of speaker [1] when it is in the appropriate position to secure it.And fix speaker [1] bracket [2] onto the roll bar through the throat pipe [3] as shown in the diagram (Note: the bracket [2] is adjustable within a length range of 450-755mm/17.7-29.5in).

WIRING DIAGRAM

KEMIMOTO B0117-03001BK UTV Sound Systems - DIAGRAMKEMIMOTO B0117-03001BK UTV Sound Systems -
DIAGRAM1

FUNCTION AND OPERATION

  1. Power/Mode button
    Power on/off: long press for power on function.
    Mode switch: short press to cycle through BT-AUX-USB mode.

  2. Play/Pause button

  1. When playing USB music, AUX music or Bluetooth music, short press for pause function, short press again to resume playback.
  1. Previous track/Decrease volume button
  1. When playing USB music, AUX music or Bluetooth music, short press for previous track selection.
  2. During music playback, long press for volume decrease function.
  1. Next track/Increase volume button
  1. When playing USB music, AUX music or Bluetooth music, short press for next track selection.
  2. During music playback, long press for volume increase function.

BLUETOOTH PAIRING

KEMIMOTO B0117-03001BK UTV Sound Systems - BLUETOOTH
PAIRING Pair your phone with your speaker

  1. Long press and hold the power button to turn on;
  2. Shot press again to switch to BT mode;
  3. Bring your phone close to the main unit and turn on the Bluetooth function on your phone;
  4. Search for the main unit’s Bluetooth name “KEMIMOTO-T1” on your phone;
  5. Once the Bluetooth connection is successful, the main unit will emit a “ding” sound.

FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
    To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

www.kemimoto.com
Designed by Kemimoto Group
Kemimoto All Rights Reserved, Infringement must be prosecuted.

Documents / Resources

| KEMIMOTO B0117-03001BK UTV Sound Systems [pdf] User Manual
2A449KEMIMOTO-T1, B0117-03001BK, B0117-03001BK UTV Sound Systems, UTV Sound Systems, Sound Systems
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals