X32-PHZ3V Can Am X3 Phase 3 V Spec 3 Speaker

“`html

Specifications:

• Product Name: X32-PHZ3V
• Compatibility: 2017-2023 Can Am Maverick X3 Phase 3
• Features: V-Spec, 3-Speaker 1650 Watt Audio Kit

Product Usage Instructions:

Panel Disassembly

Follow the instructions provided in the user manual for
disassembling the panels of your Maverick X3.

RGB LED Controller Command Center Installation

Refer to the manual for step-by-step guidance on installing the
RGB LED Controller Command Center for your audio kit.

Dash Speaker Panel Installation

Install the dash speaker panel according to the instructions
provided in the manual to ensure proper placement and
functionality.

Amp Installation

Follow the detailed steps outlined in the manual for installing
the amp included in the audio kit.

JVC MR1 Installation

Install the JVC MR1 unit using the provided components and
guidelines. Always refer to the JVC manual for specific headunit
instructions.

Subwoofer Installation

For installing the subwoofer, follow the instructions given in
the manual to ensure optimal audio performance.

FAQ:

Q: What tools are required for installation?

A: The tools needed include T30 torx, 10mm wrench or ratchet,
13mm wrench or ratchet, 18 mm socket with extension, wire crimpers,
panel removal tool, #2 screwdriver, and #3 screwdriver.

“`

SSV WORKS, 2610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

X32-PHZ3V
2017-2023 Can Am Maverick X3 Phase 3, V-Spec, 3-Speaker 1650 Watt Audio Kit

pg 7
Panel Disassembly
pg 9
RGB LED Controller Command Center Installation
pg 9
Dash Speaker Panel Installation
pg 12
Amp Installation
pg 15
JVC MR1 Installation
pg 18
Subwoofer Installation

Maverick X3

1

PARTS LIST 1/5

SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. All SSV Works Speakers are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

TOOLS NEEDED FOR INSTALLATION

– T30 torx – 10mm wrench or ratchet – 13mm wrench or ratchet

– 18 mm socket with extention – Wire crimpers – Panel removal tool

– #2 screw driver – #3 screw driver

PARTS LIST IMAGES

Amp/Wiring Installation

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

Amp Tray with pre-loaded Kicker 400.4 & 600.1 Amps

Amp Power Wire x2 (A-H1Q)

Front RGB Harness (B-H2935)

Front Speaker Harness (B-H1385)

RCA Patch Cable, Male to Male (B-X3-HRCA)

2-Pin Sub Extension (A-H2702K)

RGB Extension Harness, 2 ft. (B-H2934)

2-Pin to Male RCA x2 (B-H3543)

Fuse Holder with 40A Fuse

Battery Terminal Cable

Zip Ties x 5

2

PARTS LIST 2/5

SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Dash Kit

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION

– T25, T30, T40 torx driver

– #2 phillips screwdriver

– air saw and safety equipment – Drill and 1/8″ and 1/4″ drill bit

PARTS LIST IMAGES

JVC MR1 Headunit

MR1 Trim Ring

DMR1 Dash Kit x1

DMR1 Base Plate x1

MR1 dash screws x2

M6 x 1.0 Screws, Nuts & Washers x4 (T-30 torx)

Push Pins x2

Drill Guides x4

JVC MR1 to SSV Adapter Harness (B-H2368)
INSTALLATION NOTES
Always disconnect the battery. For instructions regarding the headunit, refer to the JVC manual.
3

PARTS LIST 3/5

SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

RGB LED Controller Command Center

WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION – Cutter

LIT-CC, 3 Output RGB LED Controller Command Center

LIT-CC, RGB LED Controller Rocker Switch

Power Pigtail
Included Universal Controller Pigtails are NOT used in this installation.
4

Zip Ties (x2)

PARTS LIST 4/5

SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

6.5″ Dash Speaker Panels

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION – T20 & T30 Torx Driver

– 8, 10 & 13mm Socket Wrench

Speaker Panel, Drive Side

Speaker Panel, Passenger Side

Vibration Dampening Loop Clamp

Hardware Pack [B-HP3551]

Smart-Lok Module Relocation Bracket [B-MB3546] 5

PARTS LIST 5/5

SSV WORKS, 4610 Calle Quetzal, Camarillo, CA 93012 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. Labor for replacement of defective components is not covered. Contact SSV Works for further warranty information.

10″ Driver Side Under Seat Subwoofer Enclosure

Please read and understand these

!

instructions completely before installation to avoid possible injury, or

damage to the accessory or vehicle.

TOOLS NEEDED FOR INSTALLATION

– 10mm, 13mm, 16mm and 18mm Sockets & Wrenches

– T-30 & T-40 Torx Driver

– 1½” Hole Saw

– Hole Punch / Scribe Tool

– Ratchet & Extension

– #3 Phillips Screwdriver

PARTS LIST IMAGES

1. X32-DUS10 Enclosure

2. M6 x 16mm Screws & Washers x 10 (T-30 torx)

Triangular end
3. Thread Rolling Screw x 2

4. M6 x 25mm Screw x 1

5. Large washers x 2

6. C-Bracket

7. A-Bracket x 1

8. Large Bracket

9. Seat Spacer x 1 6

10. Small Spacer x 1

11. M6 Locking Hex Nut

12. Foam Strips x 5

PANELS AND DASH DISASSEMBLY

A

A

A. To remove the seat, use a 13mm socket and wrench to remove front (2) bolt and nut, and use a 18mm socket to remove (2) rear nuts and seat belt nut ( repeat on other seat)

B

B

B

B. Carefully unsnap console panels by hand or with a panel removal tool.

C
C. Unscrew (2) T30 torx located on the center console panel under the dash. Use a panel tool to remove push pins on passenger side.

D
D. Carefully unsnap rear cover to expose the engine compartment
7

E

E

E

E. Remove gas cover on the passenger side to expose a 10mm nut. Unscrew with a wrench and T30 torx driver.

E2

E2

E2

E2. Using panel removal tool unsnap (2) push clips on the driver and passenger side dash covers. Unscrew the (4) T30 screws on the passenger side, and (7) T30 screws on the driver side.

F
F. Remove fender well panel using a T30 driver (will need a10mm socket for the screw near the headlight)

G
G. After the fender well panel is removed, remove the third fastener clip from the bottom.

8

DASH SPEAKER PANEL INSTALLATION
TOOLS NEEDED FOR INSTALLATION – T20 & T30 Torx Driver

– 8, 10 & 13mm Socket Wrench

Refer to the X3-DP6K installation manual included in the kit for a detailed installation process of the dash speaker panels.

RGB LED CONTROLLER COMMAND CENTER INSTALLATION

TOOLS NEEDED FOR INSTALLATION

– Wire Cutter

– Wire Stripper

– Crimper

A
A. Install the LIT-CC RGB LED Controller Rocker Switch in an unoccupied rocker switch opening.

B
B. Mount the LIT-CC RGB LED Controller Command Center in the dash away from moving parts and secure with zip ties. Cut excess zip ties for a clean install.

NOTE: Refer to the 230-LIT-CC User Guide for detailed operation instructions.

9

RUNNING WIRE HARNESSES
AMP POWER CABLES
JVC MR1 POWER HARNESS
Bus Bar
LIT-CC RGB CONTROLLER WIRING
10

Battery

Fuse Fuse

LIT-CC

400.4 600.1
JVC MR1

400.4 600.1

Connect the A-H1Q (x2) power/ground wire from the amplifiers to the battery. Use the provided fuse holder for circuit protection.
Connect the JVC MR1 to SSV adapter harness (B-H2368) to the factory bus bar located in the center console beside the passenger seat. Connect the blue amp turn on wire to the amplifiers.
Run the B-H2965 Front RGB harness from the LIT-CC output to the dash speaker panels. Mount the LIT-CC Controller in an empty rocker switch slot and route the cable to the LIT-CC RGB Controller.

SUBWOOFER AUDIO CABLES

Amplifier

Run the B-H2702 Subwoofer extension cable from 600.1 amplifier to the subwoofer. The subwooder enclosure can be mounted under
the driver or passenger seat.

DASH SPEAKER PANEL AUDIO CABLES
Run the B-H1385 front speaker harness from 400.4 amplifier to the dash speaker panels. The shorter end of the harness goes to the driver side dash speaker panel.

400.4

11

AMP WIRING
400.4
600.1
AMP PLATE INSTALLATION
Mounts to ROPS Cage bolt
For optional ALPHA12
Switcher bracket
12

Power/Ground Amp Turn On Remote Bass Front Inputs Rear Inputs Front Outputs Rear Outputs Power/Ground Sub Output Remote Bass Sub Inputs Amp Turn On
Mounts to Firewall
Mounts to tube chassis

The amp tray mounts on the driver side firewall above the tube chassis.

A
A. Make a pilot hole with a pick tool through the top right screw hole in the amp plate and push all the way through the vehicle panel.

B
B. Drill a hole through the pilot holes using a 1/4″ drill bit. Be sure to move the amp plate out of the way before drilling.

C
C. Secure the amp tray to the vehicle’s ROPS cage using the supplied M6 flange hex head Bolt, 10mm nut and washer.

D
D. From the outside of the firewall, use the included M6 x 16mm screw and washer to secure the amp plate through the hole you drilled on the firewall.

E
E. Mount the loop clamp to the bottom tube chassis and secure it to the amp tray using a M4 x 12mm phillips screw and washer.

13

F

F2

F. Route the front speaker harness (B-H1385) and RGB harness (B-H2935) towards the driver and passenger side of the vehicle and plug in the 4 pin audio connector to the 400.4 amplifier front outputs. Leave the 4 pin RGB connector at the center of the dash or LIT-CC RGB
Controller mounting location.

G

G2

G. Connect the subwoofer outputs of the 600.1 amplifier to the 2 pin subwoofer audio extension harness (B-H2702) (G). Connect amplifier power harnesses to 400.4 and 600.1 amplifiers (G2).

3

1

4

2

H

H2

H. Audio Wiring Connections: 400.4 Amp [1] Input (AMP1 R/L) B-H3543 RCAs B-H2368 (SSV to JVC Adapter Harness) 4 Pin Front Output [2] Front Outputs B-H1385 To front speakers [3] Rear Outputs B-H1385 To Rear Cage Pod Speakers (Sold Separately)
600.1 Amp [3] Input (SUB R/L) B-HX3RCA (RCA Patch Cable) JVC MR1 Sub-W Lineout RCAs [4] Subwoofer Output A-H2702K (2 pin Subwoofer Extension Cable X3-DUS10 Sub Woofer
H2. Plug in Amp turn on wires from both amps to the B-H2368 (SSV to JVC Adapter Harness) turn on wire.
14

DASH KIT ASSEMBLY

A

A

A. Set the base plate on the dash. Press the (4) drill guides onto the base plate

B

C

B. Using a 1/8″ drill bit, drill the center of the drill guides to provide pilot holes. Limit speed and depth of the drill bit to avoid damaging any wiring.

C. Set aside the base plate and open the pilot holes up with a 1/4″ drill bit.

D
D. Reset the base plate, trace the outline of the baseplate circle.

E
E. Cut out the traced circle. Limit speed and depth of cutting device to avoid damaging any wiring.

15

F
F. Place (4) M6 T30 screws and washers into each drilled hole. Fasten from the bottom a washer and M6 nut. Secure each screw with 10mm wrench and T30 torx driver.

G
G. Using a #2 phillips screwdriver, secure the front of the base plate with the provided (2) #6 x ½” screws.

H
H. Route the MR1 power harness and 500.1 audio input and any other related accessories out of the cutout.

I
I. Place the DMR1 over the base plate with the harness routed out of it.

J
J. Place the MR1 into the DMR1. When placing the MR1 into the dash mount, feed slack wiring back into the dash cavity cut out. This will allow for proper fitment of the MR1.
16

K
K. Secure the MR1 with the (4) M3.5 screws provided with the MR1. The top (2) screws will thread into the DMR1. The lower (2) screws will go through the DMR1 and into the threads of the base plate.

L. Secure the backside of the DMR1 with (2) push pins.

L

M

M. Center the trim ring on the MR1 and firmly press down until the side and corners click into place.

JVC MR1 WIRING CONNECTION

A

B

A. Connect the blue “AMP TURN-ON” from the
MR1 power harness, to the blue, “AMP TURNON” on the 400.4 and 600.1 amplifierss.

B. Connect the front (white/gray) output from the MR1 power harness to the front input of the 400.4 amp.

C
C. Connect the B-X3RCA patch cable between the Sub-W Line Out of the MR1 to the subwoofer L/R input of the 600.1 amp.

D

D

D. Connect the MR1 power and ground wires to the power strip located on the passenger side of the center console.

D
17

UNDER SEAT SUBWOOFER ENCLOSURE (DRIVER SIDE)
THIS STEP IS OPTIONAL
Some x3 models have a thinner skid plate than others and may rattle more. We have provided a drill template to help minimize skid plate rattle.

1

2

H. To help minimize skid plate rattle, we have supplied a drill template that adds 4 holes to help relieve air pressure that is being generated by the high
output of the sub enclosure. Use the mounting bracket for the front of the sub enclosure for reference. Line up the template under the sub mounting brackets. (1). With hole punch/scribe tool mark the 4 drilling points through the template on to the floorboard (2). Drill the four (4) – 1½” holes with a hole saw (3).

A1

A2

A. Apply the short foam strips to the large bracket in the order shown above (A1). Apply the long foam strips to the outside edges of the enclosure. (Driver outside = left / Passenger outside = right) (A2).

18

B
B. Using the supplied T-30 torx M6 screws and washers, screw the C bracket to the bottom left side of the enclosure.

C
C. Using the supplied T-30 torx M6 screws and washers, screw the Large bracket to the right side of the enclosure shown above. Do not screw in all the way, leave the screws somewhat loose so that you can fit the enclosure snug and then tighten the screws after.

D

D

D. To remove driver the seat, use a 13mm socket and wrench to remove front (2) bolt and nut, and use a 18mm socket to remove (2) rear nuts and (1) 16mm seat belt bolt. Disconnect the seat belt sensor.

E

E

E

E. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long M6x25mm screw through the top. Then attach the brake line, spacer, washer and nut. (Disregard this step for the 4-seat Maverick X3 Max)

19

F
F. Remove the seat mounting spacer from the seat mounting stud towards the center of the car. Feed the enclosure down under the seat bar and simultaneously guide “Bracket C” over the inner seat mounting stud that does not have the spacer. The Factory spacer will not be re-used*** As the enclosure is set into place, the brake line is to run along the dedicated channel on the sub enclosure. Make any routing adjustments to the brake line so the enclosure lays down flat without any tension on the brake line. Bracket C should be sitting flat on top of the floor plastic once the enclosure is in place.

G
G. Replace the factory seat bolt spacer with the supplied SSV Works spacer on top of bracket C.

H1

H2

H3

H. Place bracket A to the right side of the enclosure (H1). Line up the 2 screw holes and proceed to hand thread the T-30 torx screws and washers. Use a T-30 torx bit to tighten screws (H2). Line up the top of bracket A hole on the factory seat brakcet. Screw in the T-30 torx screw with the large washer (H3).

I
I. The large bracket will align over (2) factory holes in the chassis. Using a

3 Phillips screwdriver, secure the large bracket to the chassis with the

provided (2) thread rolling screws and washers.
20

J

J

J. Route the B-H2702 sub extension harness along the center console away from any moving parts and sharp metal towards the rear of the vehicle then connect to the B-H3081 “Y” splitter. Plug one end of the “Y” splitter to the B-H3074 2-pin extension (3 ft) to the X32-DUS10 (driver side).

CONNECTING POWER & GROUND CABLE TO BATTERY

A

A

A. Unscrew the factory nut on the negative battery terminal. Install the 2 ground cables to the screw on the ground battery terminal. Re-install the factory nut.

B

B

B. Unscrew the factory nut on the positive battery terminal. Install the 2 power cables to the screw on the postive battery terminal. Re-install the factory nut.

21

C
C. Zip tie all wiring to the factory cables away from any moving parts.
THIS CONCLUDES THE INSTALLATION PROCESS. REPLACE THE FACTORY PANELS AND SEATS. QUESTIONS? PLEASE CONTACT SSV WORKS AT 818-991-1778 OR EMAIL SUPPORT@SSVWORKS.COM
© 2024 SSV Works, Camarillo, CA 93012 X32-PHZ3V 7-29-24
22

References

• SSV Works

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>