KICHLER 55150CPZ Champagne Bronze Bathroom Vanity Light Instruction Manual

June 15, 2024
KICHLER

KICHLER 55150CPZ Champagne Bronze Bathroom Vanity Light

Product Specifications

  • Mounting Strap [A]
  • Outlet Box [B]
  • Strap Mounting Screw (2) [C]
  • Mounting Screw (2) [D]
  • Canopy [E]
  • Knob (2) [F]
  • Lock Washer (2) [G]
  • Glass Shade [H]
  • Socket Base Cup [I]
  • Socket [J]

Product Usage Instructions

Installation Instructions

  1. 1. Find the appropriate threaded holes on the mounting strap [A] that align with the hole distance in the canopy [E]. Thread the mounting screws [D] into the threaded holes starting from the outlet box [B] side.
  2. Attach the mounting strap [A] to the outlet box [B] using the strap mounting screws [C]. The mounting strap can be adjusted to suit the position of the fixture.

  3. Grounding instructions

  4. On fixtures where the mounting strap is provided with a hole and two raised dimples
    Wrap the ground wire from the outlet box around the green ground screw and thread it into the hole.

  5. On fixtures where a cupped washer is provided
    Attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread it into the mounting strap.

  6. If the fixture is provided with a ground wire, connect the fixture ground wire to the outlet box ground wire with a wire connector after following the above steps. Never connect the ground wire to black or white power supply wires.

Make wire connections

  1. Connect the black or red supply wire to the corresponding color on the fixture (black).
  2. Connect the white supply wire to the corresponding color on the fixture (white).
  3. Refer to the reference chart below for correct connections
Supply Wire Fixture Wire
Black or Red Black
White White
Parallel cord (round & smooth) Clear, Brown, Gold, or Black without Tracer
Parallel cord (square & ridged) Clear, Brown, Gold, or Black with Tracer
Insulated wire (other than green) with copper conductor Insulated wire (other

than green) with silver conductor

Note : When parallel wires (SPT 1 & SPT 2) are used, the neutral wire is square shaped or ridged, and the other wire will be round in shape or smooth.

Push the fixture to the wall, carefully aligning the mounting screws protruding from the mounting strap with the holes in the canopy.

Important: The fixture can be mounted with the glass shade in the up or down position. Make sure all wires are inside the canopy and do not get pinched between the mounting strap and canopy or wall and canopy of the fixture.

  1. Slip lock washers [G] over the threads protruding through the holes in the canopy (2 places).
  2. Screw knobs [F] onto the threads protruding through the holes in the canopy (2 places) and tighten to secure the fixture to the wall.
  3. Insert the recommended bulb(s) (not included).
  4. Carefully pass the opening in the glass shade [H] over the bulb and socket [J]. While holding the socket base cup [I] with one hand, gently press the glass shade against the socket base cup and turn the glass shade clockwise into the socket base cup [I] until it is locked in place. Do not over-tighten.
  5. Repeat steps 8 and 9 for remaining sockets (if applicable).

Frequently Asked Questions (FAQ)

  • Q: Can I mount the fixture with the glass shade facing up?
    A: Yes, the fixture can be mounted with the glass shade in the up or down position.

  • Q: How do I make wire connections?
    A: Connect the black or red supply wire to the corresponding color on the fixture (black), and connect the white supply wire to the corresponding color on the fixture (white). Refer to the reference chart in the installation instructions for more details.

  • Q: Can I use parallel cords with this fixture?
    A: Yes, you can use parallel cords. When using parallel cords (round & smooth or square & ridged), make sure to connect the wires according to the reference chart in the installation instructions.

FIXTURE DIAGRAM

PARTS LIST

  •  Mounting Strap
  • Outlet Box
  • Strap Mounting Screw (2)
  • Mounting Screw (2)
  • Canopy
  • Knob (2)
  • Lock Washer (2)
  • Glass Shade
  • Socket Base Cup
  • Socket

CAUTIONS
CAUTION – RISK OF SHOCK
Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.

WARNING
This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING

  • Always be certain that electric current is turned off before cleaning.
  • Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

  1. Find the appropriate threaded holes on mounting strap[A] that align with  hole distance in canopy[E]. Thread mounting screws[D] into threaded holes starting from outlet box[B] side.

  2. Attach mounting strap[A] to outlet box[B] using the strap mounting screws[C]. Mounting strap can be adjusted to suit position of fixture.

  3. Grounding instructions (See Illus. a or b).

  4. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.

  5. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
    If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

  6. Make wire connections. Reference chart below for correct connections and wire accordingly.

Connect Black or Red Supply Wire to Connect White Supply Wire to
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer Clear, Brown, Gold or Black with

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

  • Note : When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)| Neutral Wire

    1. Push fixture to wall, carefully aligning the mounting screws protruding from the mounting strap with holes in canopy.
      NOTE : Fixture can be mounted with glass shade in the up or down position. Make sure all wires are inside canopy and do not get pinched between mounting strap and canopy or wall and canopy of fixture.

    2.  Slip lock washers[G] over threads protruding through holes in canopy (2 places).

    3. Screw knobs[F] onto threads protruding through holes in canopy (2 places) and tighten to secure fixture to wall.

    4. Insert recommended bulb(s) (not included).

    5.  Carefully pass the opening in glass shade[H] over bulb and socket[J]. While holding the socket base cup[I] with one hand, gently press the glass shade against the socket base cup and turn the glass shade clockwise into the socket base cup[I] until it is locked in place to secure.
      DO NOT OVER-TIGHTEN.

    6. Repeat steps 8 and 9 for remaining sockets (if applicable).

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KICHLER User Manuals

Related Manuals