VODALAND MONO 300PC Trench Drain Installation Guide

VODALAND MONO 300PC Trench Drain

Specifications

•  Load Class: E600
• Concrete Encasement Depth (A): 10″ (250mm)
• Concrete Encasement Width (C): 8″ (200mm)
• Materials:
  • Compressive Strength: 14,000 PSI
  • Flexural Strength: 4,000 PSI
  • Tensile Strength: 1,500 PSI
  • Water Absorption: 0.05%
  • Frost Proof: Yes
  • Dilute Acid and Alkali Resistant: Yes
  • Salt Proof: Yes

Product Usage Instructions

Concrete Encasement and Installation

The specifier is responsible for concrete encasement and reinforcing based on application and local codes. It is recommended to use expansion and contraction control joints and reinforcement to protect the channel and concrete surround. Consult with the manufacturer for installation instructions.

Finishing Details

If the trench drain system has a vertical outlet at the end of the run, add an additional 4″ (100mm) of concrete encasement after the end cap. The finished level of concrete surround should be 1/8 – 3/16″ (3-5mm) above the top of the channel edge.

Product Specifics

The trench drain shall be VODALAND CANADA MONO 300 as manufactured by VODALAND or approved equal. Channels are 39.4″ (1000mm) long with a nominal clear opening of 12″ (300mm) and an overall width of 15.1″ (385mm). Each unit features a full radius in the trench bottom and male-to-female interlocking joints.

Grate Design

The grate opening is monolithically cast as a part of the trench drain body as a single piece. Channels and grates are designed to withstand a required EN1433 load class.

FAQ

Q: What is the load class of the MONO 300 System?

A: The load class of the MONO 300 System is E600.

Q: What are the approximate properties of the polymer concrete used in the trench drain?

A: The approximate properties of the polymer concrete include compressive strength of 14,000 PSI, flexural strength of 4,000 PSI, tensile strength of 1,500 PSI, water absorption of 0.05%, and resistance to frost, dilute acid, alkali, and salt.

Overview

__

PARAMETER

| LOAD CLASS
---|---
CLASS E
__

CONCRETE ENCASEMENT DEPTH (A), in

| __

10” (250mm)

__

CONCRETE ENCASEMENT WIDTH (C), in

| __

8” (200mm)

NOTES :

1. THE SPECIFIER IS RESPONSIBLE FOR CONCRETE ENCASEMENT AND REINFORCING BASED ON APPLICATION AND LOCAL CODES.
2. EXPANSION AND CONTRACTION CONTROL JOINTS AND REINFORCEMENT ARE RECOMMENDED TO PROTECT CHANNEL AND CONCRETE SURROUND. ENGINEERING ADVICE MAY BE REQUIRED.
3. THIS INSTALLATION SCHEME IS A RECOMMENDATION. CONSULT WITH THE MANUFACTURER FOR INSTALLATION INSTRUCTIONS.
4.  IF THE TRENCH DRAIN SYSTEM HAS A VERTICAL OUTLET AT THE END OF THE RUN, IT IS NECESSARY TO ADD AN ADDITIONAL 4” (100mm) OF CONCRETE ENCASEMENT AFTER THE END CAP.
5. THE FINISHED LEVEL OF CONCRETE SURROUND SHOULD BE 1/8” – 3/16” (3-5mm) ABOVE THE TOP OF THE CHANNEL EDGE

GENERAL : THE TRENCH DRAIN SHALL BE VODALAND CANADA MONO 300 AS MANUFACTURED BY VODALAND OR APPROVED EQUAL

SPECIFICATION

CHANNELS SHALL BE 39.4” (1000MM) LONG AND THE NOMINAL CLEAR OPENING SHALL BE 12” (300MM) WITH 15.1” (385MM) OVERALL WIDTH AND BUILT-IN NEUTRAL SLOPE AS PER THE SPECIFIER’S REQUIREMENTS. EACH UNIT WILL  FEATURE A FULL RADIUS IN THE TRENCH BOTTOM AND FEATURE MALE-TO-FEMALE INTERLOCKING JOINTS. THE GRATE OPENING SHALL BE MONOLITHICALLY CAST AS A PART OF THE TRENCH DRAIN BODY AS A SINGLE PIECE. CHANNELS AND GRATE SHALL WITHSTAND A REQUIRED EN1433 LOAD CLASS

MATERIALS: MONO 300 TRENCH DRAIN SHALL BE MANUFACTURED FROM POLYMER CONCRETE WITH THE FOLLOWING

APPROXIMATE PROPERTIES:

• COMPRESSIVE STRENGTH                                  14,000 PSI
• FLEXURAL STRENGTH                                         4,000 PSI
• TENSILE STRENGTH                                              1,500 PSI
• WATER ABSORPTION                                            0.05%
• FROSTPROOF                                                           YES
• DILUTE ACID AND ALKALI RESISTANT           YES
• SALT PROOF                                                               YES

THE COMPLETE DRAINAGE SYSTEM SHALL BE BY VODALAND CANADA INC. ANY DEVIATION OR PARTIAL SYSTEM DESIGN AND/OR IMPROPER INSTALLATION WILL VOID ANY AND ALL WARRANTIES PROVIDED BY VODALAND CANADA INC.

CHECK AND SPECIFY APPROPRIATE OPTIONS

| Name| Article| Н, in| H, mm
---|---|---|---|---
| 12” MONO polymer concrete endcap H16.1” (end)| 67719-4K| 16.1| 410
| 12” MONO polymer concrete endcap H16.1” (beginning)| 67719-4N| 16.1| 410
| 12” MONO polymer concrete endcap H20.1” (end)| 67719-5K| 20.1| 510
| 12” MONO polymer concrete endcap H20.1” (beginning)| 67719-5N| 20.1| 510
| 12” MONO polymer concrete endcap H24.1” (end)| 67719-K| 24.1| 610
| 12” MONO polymer concrete endcap H24.1” (beginning)| 67719-N| 24.1| 610
| 12” MONO polymer concrete adaptor H16.1” (end)| 67749-4K| 16.1| 410
| 12” MONO polymer concrete adaptor H16.1” (beginning)| 67749-4N| 16.1| 410
| 12” MONO polymer concrete adaptor H20.1” (end)| 67749-5K| 20.1| 510
| 12” MONO polymer concrete adaptor H20.1” (beginning)| 67749-5N| 20.1| 510
| 12” MONO polymer concrete adaptor H24.1” (end)| 67749-K| 24.1| 610
| 12” MONO polymer concrete adaptor H24.1” (beginning)| 67749-N| 24.1| 610
| 12” MONO polymer concrete adaptor H20.1”-16.1”| 67749-5| |
| 12” MONO polymer concrete adaptor H24.1”-20.1”| 67749| |

Vodaland Canada Inc.
1-5900 Ambler Dr, Mississauga, ON L4W 2N3 • Phone: 905-238-1771 • Email: info@vodaland.ca

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>