VODALAND MONO 200PC Trench Drain Installation Guide

August 28, 2024
VODALAND

VODALAND MONO 200PC Trench Drain

Specifications

  • Product Name: MONO 200 SYSTEM
  • Load Class: D400-E600
  • Material: Polymer Concrete
  • Compressive Strength: 14,000 PSI
  • Flexural Strength: 4,000 PSI
  • Tensile Strength: 1,500 PSI
  • Water Absorption: 0.05%
  • Frost Proof: Yes
  • Dilute Acid and Alkali Resistant: Yes
  • Salt Proof: Yes

FAQ

  • Q: What should I do if I need engineering advice for the installation?
  • A: If you require engineering advice, consult with a professional to ensure proper installation and adherence to local codes.
  • Q: Can I modify the trench drain system design?
  • A: Any deviation from the recommended installation scheme may void warranties. Consult with the manufacturer for guidance on modifications.

INSTALLATION

8” (200mm) MONO POLYMER CONCRETE TRENCH DRAIN

NOTES

  1. SPECIFIERS ARE RESPONSIBLE FOR CONCRETE ENCASEMENT AND REINFORCING BASED ON APPLICATION AND LOCAL CODES.
  2.  EXPANSION AND CONTRACTION CONTROL JOINTS AND REINFORCEMENT ARE RECOMMENDED TO PROTECT CHANNEL AND CONCRETE SURROUND. ENGINEERING ADVICE MAY BE REQUIRED.
  3. THIS INSTALLATION SCHEME IS A RECOMMENDATION. CONSULT WITH THE MANUFACTURER FOR INSTALLATION INSTRUCTIONS.
  4. IF THE TRENCH DRAIN SYSTEM HAS A VERTICAL OUTLET AT THE END OF THE RUN, IT IS NECESSARY TO ADD AN ADDITIONAL 4” (100mm) OF CONCRETE ENCASEMENT AFTER THE END CAP.
  5. THE FINISHED LEVEL OF CONCRETE SURROUND SHOULD BE 1/8” – 3/16” (3-5mm) ABOVE THE TOP OF THE CHANNEL EDGE

GENERAL

THE TRENCH DRAIN SHALL BE VODALAND CANADA MONO 200 AS MANUFACTURED BY VODALAND OR APPROVED EQUAL.

SPECIFICATION

  • CHANNELS SHALL BE 39.4” (1000MM) LONG AND THE NOMINAL CLEAR OPENING SHALL BE 8” (200MM) WITH 10.2” (260MM) OVERALL WIDTH AND BUILT-IN NEUTRAL SLOPE AS PER SPECIFIER’S REQUIREMENTS. EACH UNIT WILL
  • FEATURE A FULL RADIUS IN THE TRENCH BOTTOM AND FEATURE MALE-TO-FEMALE INTERLOCKING JOINTS. GRATE OPENING
  • SHALL BE MONOLITHICALLY CAST AS A PART OF THE TRENCH DRAIN BODY AS A SINGLE PIECE. CHANNELS AND GRATE SHALL WITHSTAND A REQUIRED EN1433 LOAD CLASS

MATERIALS

MONO 200 TRENCH DRAIN SHALL BE MANUFACTURED FROM POLYMER CONCRETE WITH THE FOLLOWING

  • APPROXIMATE PROPERTIES:
  • COMPRESSIVE STRENGTH:14,000 PSI
  • FLEXURAL STRENGTH: 4,000 PSI
  • TENSILE STRENGTH:1,500 PSI
  • WATER ABSORPTION:0.05%
  • FROSTPROOF: YES
  • DILUTE ACID AND ALKALI RESISTANCE: YES
    SALT PROOF: YES

THE COMPLETE DRAINAGE SYSTEM SHALL BE BY VODALAND CANADA INC. ANY DEVIATION OR PARTIAL SYSTEM DESIGN AND/OR IMPROPER INSTALLATION WILL VOID ANY AND ALL WARRANTIES PROVIDED BY VODALAND CANADA INC.

CHECK AND SPECIFY APPROPRIATE OPTIONS

Name Article Н, in H, mm
8” MONO polymer concrete endcap H20.1” (end) 67519-K 20.1 510
8” MONO polymer concrete endcap H20.1” (beginning) 67519-N 20.1 510
8” MONO polymer concrete adapter H20.1” (end) 67549-K 20.1 510
8” MONO polymer concrete adapter H20.1” (beginning) 67549-N 20.1 510

MONO 200 SYSTEM – LOAD CLASS D400-E600
EXPOSED ASPHALT PAVEMENT INSTALLATION

8” (200mm) MONO POLYMER CONCRETE TRENCH DRAIN

__

PARAMETER

| LOAD CLASS
---|---
CLASS D
__

CONCRETE ENCASEMENT DEPTH (A), in

| __

10” (250mm)

__

CONCRETE ENCASEMENT WIDTH (C), in

| __

10” (250mm)

NOTES

  1. SPECIFIERS IS RESPONSIBLE FOR CONCRETE ENCASEMENT AND REINFORCING BASED ON APPLICATION AND LOCAL CODES.
  2.  EXPANSION AND CONTRACTION CONTROL JOINTS AND REINFORCEMENT ARE RECOMMENDED TO PROTECT CHANNEL AND CONCRETE SURROUND. ENGINEERING ADVICE MAY BE REQUIRED.
  3. THIS INSTALLATION SCHEME IS A RECOMMENDATION. CONSULT WITH THE MANUFACTURER FOR INSTALLATION INSTRUCTIONS.
  4. IF THE TRENCH DRAIN SYSTEM HAS A VERTICAL OUTLET AT THE END OF THE RUN, IT IS NECESSARY TO ADD AN ADDITIONAL 4” (100mm) OF CONCRETE ENCASEMENT AFTER THE END CAP.
  5. THE FINISHED LEVEL OF CONCRETE SURROUND SHOULD BE 1/8” – 3/16” (3-5mm) ABOVE THE TOP OF THE

GENERAL

THE TRENCH DRAIN SHALL BE VODALAND CANADA MONO 200 AS MANUFACTURED BY VODALAND OR APPROVED EQUAL.

SPECIFICATION

  • CHANNELS SHALL BE 39.4” (1000MM) LONG AND THE NOMINAL CLEAR OPENING SHALL BE 8” (200MM) WITH 10.2” (260MM) OVERALL WIDTH AND BUILT-IN NEUTRAL SLOPE AS PER THE SPECIFIER’S REQUIREMENTS. EACH UNIT WILL FEATURE A FULL RADIUS IN THE TRENCH BOTTOM AND FEATURE MALE-TO-FEMALE INTERLOCKING JOINTS. GRATE OPENINGS SHALL BE MONOLITHICALLY CAST AS A PART OF THE TRENCH DRAIN BODY AS A SINGLE PIECE. CHANNELS AND GRATE SHALL WITHSTAND A REQUIRED EN1433 LOAD CLASS

MATERIALS

  • MONO 200 TRENCH DRAIN SHALL BE MANUFACTURED FROM POLYMER CONCRETE WITH THE FOLLOWING
  • APPROXIMATE PROPERTIES:
  • COMPRESSIVE STRENGTH 14,000 PSI
  • FLEXURAL STRENGTH:4,000 PSI
  • TENSILE STRENGTH:1,500 PSI
  • WATER ABSORPTION: 0.05%
  • FROST PROOF: YES
  • DILUTE ACID AND ALKALI RESISTANT: YES
  • SALT PROOF: YES

CHECK AND SPECIFY APPROPRIATE OPTIONS

  Name Article Н, in H, mm
  8” MONO polymer concrete endcap H20.1” (end) 67519-K 20.1 510
  8” MONO polymer concrete endcap H20.1” (beginning) 67519-N 20.1 510
  8” MONO polymer concrete adapter H20.1” (end) 67549-K 20.1 510
  8” MONO polymer concrete adapter H20.1” (beginning) 67549-N 20.1 510
  8” MONO polymer concrete endcap H12.1” (end) 67519D-3K 12.1 310
  8” MONO polymer concrete endcap H12.1” (beginning) 67519D-3N 12.1 310
  8” MONO polymer concrete adapter H14.1” (end) 67519D-4K 14.1 360
  8” MONO polymer concrete adapter H14.1” (beginning) 67519D-4N 14.1 360

CONTACT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals