NICREW Classic LED Plus Aquarium Light Instruction Manual

NICREW Classic LED Plus Aquarium Light

Important Safety Instructions

WARNING – To guard against injury, basic safety precautions should be observed including the following:

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
• Never operate a fixture that is damaged or malfunctioning, discon­tinue use immediately and return the appliance to an authorized service facility.
• Ensure your hand is dry when turning the power switch on/off and when inserting/removing the power cord from the receptacle.
• If the light falls into water, do not reach for it, unplug it and then retrieve it. If the electrical components of the appliance get wet, unplug the appliance immediately(Non-immersible equipment only).
• Close supervision is necessary when any appliance is used by or near children.
• The operating voltage must be compatible with the transformer’s voltage requirements.
• A G.F.C.I (Ground fault circuit interrupter) & surge protector is recommended for all electrical appliances.
• Ensure the fixture is securely installed before supplying power to the unit.
• Don’t look directly into the LEDs.
• Read and observe all the important notices and warnings on the fixture and power cord. DO NOT REMOVE THE WARNING LABEL.

Important Warning I Drip Loops
Mount your power supply where it won’t get wet. Include a “drip loop”. Drip Loops should always be used to help prevent water from traveling along the cord and coming into contact with an electrical outlet. Drip loops must always be below the level of the outlet. If the plug or outlet does get wet, DO NOT TOUCH the cord. Disconnect the fuse or circuit breaker that supplies power to the system. After disconnecting the power, unplug and examine for the presence of water.

Quick Installation

This product is recommended for use over acrylic or glass-covered aquariums.

• Slide the adjustable docking legs on the side of the fixture to match the length of your aquarium.
• Connect the female DC plug to the male DC plug from the transfo­rmer/power supply.
• Plug the transformer into a G.F.C.I approved outlet. Be sure to inco­rporate a “drip loop” as described and illustrated in Fig.1.
• Position the wired controller in an accessible location.

Programming Process

First Time Setup
Before using your controller for the first time, press and , simultaneously, hold them down for 3 seconds to reset the timer. This resets the unit to default factory settings.

Set the Clock

• a. Press for 2 seconds, the clock display will begin to flash.
• b. Press HOUR+ and MINUTE – to adjust to the correct hours and minutes.
• c. Press to exit current time setting and will advance you to the Channel 1 ON time setting.

NOTE: If you are using the pre-programmed times you are now set and the fixture will turn the channels on and off based on the pre­programmed settings. Leave the fixture idle for about 30 seconds and it will automatically exit the set-up mode.

Set the Timer
If you are changing the pre-programmed settings, proceed to program your desired settings.
NOTE: When you toggle through the programming, don’t leave the fixture idle too long. Otherwise, you will need to start over.

• a. Press after setting the clock (completed above), the LCD display will show “1 ON” briefly and flash a time. Press HOUR+ and MINUTE­to set hours and minutes- this is when you would like your LEDs of Channel 1 to turn on.
• b. Press , the LCD display will show “lOFF” briefly. Press HOUR+ and MINUTE – to set hours and minutes- this is when you would like your LEDs of Channel 1 to turn off.
• c. Press , the LCD display will show “1100” briefly which is the default setting. Press HOUR+ and MINUTE – to set the light brightness. The first digit is the channel number you are setting (l=Channel i 2=Channel 2).
• d. Repeat (a) to (c) to set Channel 2.
• e. Press again, the LCD display will flash the current ramp time mode. Press HOUR+ or MINUTE – to choose 00, 15, or 30.
• f. Press to save and exit the setting.

NOTE:

• The sunrise begins at the START time.
  For example, if you want the light to come ON at 09:00 and program a 15-minute sunrise, the light will reach 100% at 09:15.

• The sunset begins at the END time.
  For example, if you program the END time at 17:00 with a 15-minute sunset, the light will be completely out at 17:15.

• All channels can be run simultaneously or consecutively.

Manual ON/OFF

If, at any time, you wish to turn your light on, simply press . Press again to cycle throught the following channels.

Press to resume the normal timing cycle.
NOTE: The manual mode light brightness is fixed 100%.

Reset Function
Press and hold and for 3 seconds.
This resets all programmed settings to the default factory settings.

Default Lighting Schedules

8 Hours full brightness of CHl and 10 Hours 60% brightness of CH2.

Frequently Asked Questions

• If the power goes out, will the controller remember my settings?
  Yes, the controller has an internal memory that will store your settings except current time. You still need to reset the clock.

• Why does my LED light not as bright as it should be when using it?
  Please check the light brightness of CHl and CH2, and increase them to 100%.

• Why does it take less than 15 minutes to ramp up/dim down?
  The brightness will ramp up from 0% to 100% in 15 minutes. Ramp up from 0% to 1% will need about 9 seconds. So as the brightness decreases, the ramp-up/dim- down time will be proportionally shorter.

Maintenance

• Always turn off the light and unplug the power cord before perfor­ming any maintenance.
• Water spray and water scale can create an electrical and fire safety hazard if allowed to collect on fixture. To prevent hazard, use over covered aquarium only and clean fixture regularly. Wipe exterior of fixture down with a clean, freshwater-dampened towel. Then dry thoroughly with a second dry towel. Make sure all surfaces are dry before servicing.

Limited Warranty
NICREW products carry a 12-month limited warranty from the date of purchase. If your product is within warranty and you require a rep­lacement part or service, please contact us at support@nicrew.com. For more information, please visit www.nicrew.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>