ceado E37SD Coffee Grinder User Manual
- June 8, 2024
- Ceado
Table of Contents
E37SD Coffee Grinder
User Manual
COFFEE GRINDER
USE AND MAINTENANCE MANUAL
E37SD Coffee Grinder
COFFEE GRINDER E37SD-Single dose
The coffee grinder E37SD-Single dose is a professional machine for grinding
coffee for single-dose and distributing it through a discharge opening.
Like all appliances, it should be used with particular care to avoid injury to
personnel and damage to the appliance.
It is essential to read these instructions carefully before using the
appliance and to follow the safety recommendations.
It is possible to obtain the CE declaration of conformity by contacting the
manufacturer at the address shown on the product data plate.
** Do not use the appliance if you have not read and understood these
instructions!
COFFEE GRINDER E37SD
** Main parts (Fig. 1, Fig. 2, Fig. 3)
- Base
- Bellows
- Bellows support
- Grinding adjustment toothed disc
- Disc unlocking button for quickadjustment
- Grinding adjustment knob
- Motor start/stop button
- Discharge spout cover
- Discharge spout
- Support fork
- Tray
- ON-OFF (I-O) switch
- Container
- Funnel for filter-holder
- Coffee bean shaker
- Spray bottle
- Paintbrush
SAFETY RECOMMENDATIONS GENERAL INSTRUCTIONS
-
Read the following instructions carefully before using the appliance.
-
This appliance is intended for internal use only.
-
The maximum and minimum room temperature for correct operation of the appliance are respectively 32°C and 10°C.
-
Installation and maintenance should be carried out by qualified personnel only who are authorized for such tasks.
-
Make sure that the mains voltage is as indicated on the rating label of the appliance and that the electrical system is grounded and equipped with a switch.
-
Plug the power cable into a socket protected by a suitably rated circuit breaker (MCB) or fuses. Do not use an adaptor plug.
-
Install the appliance in a DRY, PROTECTED place, far from water sprays and jets, heat sources, open flames and inflammable substances.
-
Place the appliance on a flat, horizontal, stable surface where it cannot tip over.
-
This appliance is intended for professional use, and should therefore be used by experienced personnel only who are trained for this purpose. This appliance is NOT intended for industrial food processing in mass production.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental abilities, or without experience and knowledge, unless they have been instructed in the use of the appliance and are under the supervision of a person who is responsible for their safety.
CHILDREN SHOULD BE SUPERVISED SO AS TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE. -
Never use this appliance for purposes other than grinding coffee beans. Any other use is dangerous. Do not operate the appliance without the bellows and its collector.
-
Always work under safe conditions: do not use the appliance with wet hands or feet. Do not use outdoors.
-
Keep the original package for possible future use. It is the most suitable protection against damage during transport.
-
In case of fire use CO2 extinguishers. Do not use water or powder extinguishers.
-
Never place the appliance in water!
-
Do not disassemble the appliance or attempt to perform any repairs inside it.
-
Always unplug the appliance before performing any maintenance or cleaning and when it is not in use.
-
Never pull the appliance by the cord to move it. Never unplug it by pulling the cord or touching it with wet hands.
**** If the power cable is damaged it must be replaced by the manufacturer or by the technical assistance service, or at any rate by a person with similar qualifications, so as to prevent all risks. -
Do not use the appliance if it is damaged or has loose parts. Immediately contact an authorized Service Center.
-
Noise: the appliance does not exceed 70 dB.
The appliance complies with European regulation CE 1935/2004 and subsequent
updates.
Note: Due to statistical tests on the product in the factory, some coffee
grounds may be found in the appliance.
SAVE THESE INSTRUCTIONS!
To consult these instructions on-line, visit the site
www.ceado.com
**** The EC declaration of conformity for this appliance is available in the
Products section of our website www.ceado.com.
INSTALLATION
Comply with the Safety recommendations indicated above and hereafter when
installing the appliance.
For the installation of the appliance, qualified personnel must be present who
are able to check the fineness of the grind.
-
Make sure that the mains voltage is as indicated on the rating label of the appliance and that the electrical system is grounded and equipped with a switch.
-
Install the appliance in a DRY, PROTECTED place, far from water sprays and jets, heat sources, open flames and inflammable substances. Place the appliance on a flat, horizontal, stable surface where it cannot tip over.
-
Put the tray in its housing to keep the work area as clean as possible. Place the bellows in its housing.
**** Before connecting the plug to the power socket, make sure that the ON- OFF switch (12 Fig. 2) is in position “O” (OFF). -
Plug the power cable into a socket protected by a suitably rated circuit breaker (MCB) or fuses. Do not use an adaptor plug.
-
Stretch the power cable out to full length. Do not let it pass over sharp edges or hot surfaces. Do not let oil spill on it. Do not let the power cable hang loose from the counter on which the appliance stands.
PREPARATION AND USE
** Before first use: rinse all of the parts that will have contact with
food in running water i.e.: bellows, discharge spout cover, tray.
SWITCHING ON**
-
Turn the ON-OFF switch to position “I” (12 Fig. 2).
-
Prepare the desired quantity of coffee beans to be ground in the shaker provided (15 Fig. 2).
-
Position the filter-holder on the fork (10 Fig. 1) (with or without the supplied funnel 14 Fig. 2). If you want to pour the coffee into the container provided, insert it with its base in the fork.
-
Start the motor with the start/stop button (7 Fig. 1).
-
Always start the motor of the coffee grinder before putting coffee beans into the bellows (running empty).
-
To reduce static electricity (present especially in some types of coffee) apply 2-3 splashes of water using the spray bottle supplied (16 Fig. 2) on the beans ready for grinding.
-
Pour the desired quantity of coffee beans into the bellows opening (2 Fig. 1).
If the LED in the button (7 Fig. 1) starts to flash and you realise that the remaining time will not be enough to grind all the coffee beans, press the start/stop button again. -
After all the coffee beans have been ground completely, tap the bellows (2 Fig. 1) with your hand, making sure your palm fully covers the opening, to let all the ground coffee fall out.
-
Remove the discharge spout cover (8 Fig. 1) and remove the remaining ground coffee with the brush provided (17 Fig. 2).
Functions of the motor start/stop button and grinding time (7 Fig. 1)
A push of the button activates the motor for a period of 30 seconds. During
these 30 seconds the motor and therefore the LED will be ON.
At the end of the 30 seconds there are 10 additional seconds of motor
operation that warn the operator of the end of the cycle with a flashing LED.
So the time of the complete motor operation cycle is 40 s, except in the
following cases:
- If the button is pressed during the interval when the LED is flashing, another complete cycle is restarted; otherwise, at the end of the interval, the motor and the LED are switched off.
- If the button is pressed during the 30-second interval (LED with fixed light), the machine is switched off instantly.
- If the button is pressed during the interval when the LED is flashing, for a duration longer than two seconds, the machine is turned off instantly.
REGULATING GRINDING
When it leaves the factory the machine has a standard setting, but it may be
necessary to adjust grinding further due to various external factors such as
the type of mixture used, the humidity, temperature, or the different
distribution requirements.
The degree of grinding may be further corrected by turning the grinding
adjustment knob (6 Fig. 1) (see Fig. 4).
- To obtain a finer grind, move the knob in a counter-clockwise direction.
- To obtain a coarser grind, move the knob in a clockwise direction.
It is possible to speed up the adjustment operations by directly turning the grinding adjustment toothed disc (4 Fig. 1) (see Fig. 5 – 1, 2, 3), after having first unlocked by unscrewing and pressing the unlocking button (5 Fig.
- and moved away the adjustment block.
At the end of adjustment, remember to reposition the adjustment block and to fully tighten the unlocking button (for repositioning it is not necessary to hold the button down).
Make sure that the teeth of the grinding adjustment disc mate correctly with the gear of the adjustment block.
CLEANING
It is important to keep the appliance clean and in good working order to
ensure optimum quality of the products and long life of the appliance.
Cleaning of the appliance must be carried out by persons with knowledge and
practical experience of the appliance.
At the end of each working day, clean the outer surfaces dirty with coffee
(bellows, bellows support, discharge spout etc.).
Always disconnect the plug of the appliance from the power socket before
cleaning it.
Clean the motor housing and the tray with a cloth dampened with water or
alcohol.
Wipe with a dry cloth.
Never put the appliance under running water and never immerse in water.
– Use a paintbrush to clean the most hidden areas inside. To facilitate
cleaning, remove the discharge spout cover (8 Fig. 1).
MAINTENANCE
Maintenance must be carried out exclusively by qualified technical
personnel.
Care for the mechanical and electrical parts of the appliance is indispensable
in order to guarantee their safety and efficiency. If any parts need replaced,
authentic spare parts must always be used.
TROUBLESHOOTING
(See Table on the next page)
In case of any malfunction, defect of the appliance or if you suspect any
breakage after a fall, unplug the appliance immediately.
If you are unable to solve the problem referring to the table below, contact
an Authorized Service Centre.
Only qualified experts should repair the appliance.
We are not liable for any damage caused by repairs not made correctly and/or
by unauthorized personnel. In these cases the warranty does not apply.
| Problem | Solution |
|---|---|
| The appliance does not turn on. | • Make sure it is plugged in. |
• Make sure the safety circuit breaker is closed.
• Check that the main switch of the appliance is ON.
• If the problem occurs itself after a long period of intensive use or
overfilling, the motor could be in thermal protection lock! Wait at least 20
minutes and try again. The waiting time can be reduced by putting the
appliance in a cool place.
The coffee is not coming out of the discharge opening
correctly.| • Check that the coffee discharge opening is free.
The motor gets blocked.| • If the motor gets blocked due to incorrect
regulation of grinding or to the presence of a foreign body in the burrs, try
increasing to the coarsest grain size by turning the
grinding adjustment disc clockwise (4 Fig. 1).
If this is not enough, switch off the appliance, disconnect the plug from the
socket and consult technically qualified personnel.
DISPOSAL
Correct disposal of this product (waste electrical and electronic
equipment)
(Applicable in the European Union and other countries with separate collection
systems in conformity with European Directive 2012/19/EU and subsequent
updates)
This product has been made from high-quality parts and materials, which can be
re-used and recycled.
Therefore, do not throw the product away with normal household waste at the
end of its working life. Take it to a collection point for recycling
electrical and electronic devices. This is indicated by this symbol on the
product and in the operating manual.
Please contact your local government office for information about the exact
location of the closer collection point.
WARRANTY
This product is guaranteed against faulty materials and workmanship.
The warranty period may vary according to local laws or commercial uses of the
country where the product is marketed. Therefore, please contact the retailer
from whom the product was purchased. During the warranty period, this product
can either be repaired or replaced, at the manufacturer’s discretion, at no
additional cost only if it has been used according to the instructions in this
use and maintenance manual.
If the products needs maintenance or repairs during the warranty period,
contact your retailer for shipping instructions. The product should be shipped
in its original package or other suitable packing.
The warranty does not apply in case of neglect, misuse, abuse or unauthorized
repairs. This warranty does not apply to parts subject to deterioration
through normal use such as wear to the burrs and to the electrical parts.
The warranty is limited to the costs of repair or replacement of the product
or its defective parts, or an amount equivalent to the price paid for its
purchase. No additional requests of damages will be available to the
purchaser.
The manufacturer will not accept any liability and the warranty will be
invalidated if there is a failure to follow these instructions and the
technical and/or safety standards in the country where the appliance is to be
used.
In any case these instructions cannot cover every possible event and the user
is recommended to use the appliance responsibly.
THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY ALTERATIONS TO THE
APPLIANCE WITHOUT NOTICE
Ceado S.r.l.
Tel.: +39 041 50 30 767
Fax: +39 041 50 38 413
E-mail: [email protected]
www.ceado.com