PLANET IGS-1000 Series Industrial Ethernet Switch User Manual

PLANET IGS-1000 Series Industrial Ethernet Switch

Industrial Ethernet Switch

Specifications

• Model Name: IGS-1000-8T4X

• Item: Industrial 8-Port 10/100/1000T + 4-Port 10G SFP+ Ethernet Switch (-40~75 degrees C)

• 10/100/1000T RJ45 Ports: 8

• 1G/2.5G/10GX SFP+ Slots: 4

• PoE Ports: —

• Power Input Range: DC 9~48V

• Model Name: IGS-1000-8UP4X

• Item: Industrial 8-Port 10/100/1000T 802.3bt PoE + 4-Port 10G SFP+ Ethernet Switch (-40~75 degrees C)

• 10/100/1000T RJ45 Ports: 8

• 1G/2.5G/10GX SFP+ Slots: 4

• PoE Ports: 8 x 802.3bt DC 48~54V

Package Contents

Open the box of the Industrial Ethernet Switch and carefully unpack it. The box should contain the following items:

• Industrial Ethernet Switch x 1
• QR Code Sheet x 1
• Wall-mount Kit x 1
• DIN-rail Kit x 1
• RJ45 Dust Cap x 8
• SFP Dust Cap x 4

Product Usage Instructions

Step 1: Unpacking

1. Open the box of the Industrial Ethernet Switch.
2. Carefully remove all the items from the box.

Step 2: QR Code Setup

Please scan the QR code provided in the package to browse the online User’s Manual or Quick Installation Guide and follow the instructions to complete the setup.

FAQ

Q: What should I do if any items are missing or damaged?

If any of the items are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original packing material for repacking the product in case there is a need to return it for repair.

Q: Where can I find technical support for the Industrial Ethernet Switch?

You can visit the PLANET online FAQs at http://www.planet.com.tw/en/support/faq.
For technical support, you can email support@planet.com.tw.

Package Contents

Thank you for purchasing PLANET IGS-1000-8T4X and IGS-1000-8UP4X Industrial Ethernet Switches. The descriptions of this IGS-1000 series are as follows:

IGS-1000-8T4X

| Industrial 8-Port 10/100/1000T + 4-Port 10G SFP+ Ethernet Switch (-40~75 degrees C)
---|---

IGS-1000-8UP4X

| Industrial 8-Port 10/100/1000T 802.3bt PoE + 4-Port 10G SFP+ Ethernet Switch (-40~75 degrees C)

The hardware specifications of these models are shown below:

Item

Model Name

|

10/100/1000T

RJ45 Ports

|

1G/2.5G/10GX

SFP+ Slots

|

PoE Ports

|

Power Input Range

---|---|---|---|---
IGS-1000-8T4X| 8| 4| —| DC 9~48V
IGS-1000-8UP4X| 8| 4| 8 x 802.3bt| DC 48~54V

In the following sections, the term “Industrial Ethernet Switch” refers to the IGS-1000-8T4X or IGS-1000-8UP4X.

Open the box of the Industrial Ethernet Switch and carefully unpack it. The box should contain the following items:

If any of these are missing or damaged, please contact your dealer immediately; if possible, retain the carton including the original packing material, and use them again to repack the product in case there is a need to return it to us for repair.

Hardware Introduction

Switch Front Panel

The front panels of the Industrial Ethernet Switch series consist of Ethernet interfaces and LED indicators as shown below:

• Gigabit TP Interfaces (Port 1 to Port 8)
  Eight 10/100/1000BASE-T RJ45 copper interfaces come with 802.3bt PoE++ type 4 injector function (For IGS-1000-8UP4X)

• 10Gigabit SFP+ Slots (Port 9 to Port 12)
  Four 1G/2.5G/10GBASE-X SFP+ slots

LED Indicators

IGS-1000-8T4X

System

10/100/1000Mbps RJ45 PoE++ Ports (Port 1 to Port 8)

1000

LNK/ACT

|

Green

| Lights: To indicate the port is running at 1000Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

10/100

LNK/ACT

|

Amber

| Lights: To indicate the port is running at 10/100Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

10GBASE-X SFP+ Interfaces (Port 9 to Port 12)

1G/2.5G LNK/ACT

|

Green

| Lights: To indicate the port is running at 1000Mbps or

2500Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

10G LNK/ACT| Amber| Lights: To indicate the port is running at 10Gbps and successfully established.

IGS-1000-8UP4X

System

10/100/1000Mbps RJ45 PoE++ Ports (Port 1 to Port 8)

1000

LNK/ACT

|

Green

| Lights: To indicate the port is running at 1000Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

10/100

LNK/ACT

|

Amber

| Lights: To indicate the port is running at 10/100Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

PoE-in- Use

|

Green

| Lights: To indicate the PoE port is working in 4-pair PoE mode (End- span+Mid-span) and offers up to 95 watts of power.

Amber

| Lights: To indicate the PoE port is working in 802.3at PoE+ mode (End- span or mid-span) and offers up to 36 watts of power.

10GBASE-X SFP+ Interfaces (Port 9 to Port 12)

1G/2.5G LNK/ACT

|

Green

| Lights: To indicate the port is running at 1000Mbps or 2500Mbps and successfully established.

Blinks: To indicate that the switch is actively sending or receiving data over that port.

10G LNK/ACT| Amber| Lights: To indicate the port is running at 10Gbps and successfully established.

PoE Usage LED (For IGS-1000-8UP4X)

PoE power budget
270W| Amber| Lights: To indicate the system consumes over 270-watt PoE power budget
180W| Amber| Lights: To indicate the system consumes over 180-watt PoE power budget
90W| Amber| Lights: To indicate the system consumes over 90-watt PoE power budget

Switch Upper Panel

The upper panel of the Industrial Ethernet Switch consists of one terminal block connector within two power input.
Figure 2-3 shows the upper panel of the IGS-1000-8T4X.

Figure 2-4 shows the upper panel of the IGS-1000-8UP4X.

Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial Ethernet Switch is used for two DC redundant power inputs. Please follow the steps below to insert the power wire.

When performing any of the procedures like inserting the wires or tightening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock.

1. Insert positive and negative DC power wires into Contacts 1 and 2 for Power 1, or Contacts 5 and 6 for Power 2.
2. Tighten the wire-clamp screws for preventing the wires from loosening.

NOTE

1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG.
2. The IGS-1000-8T4X supports DC input range of 9V to 48V. The IGS-1000-8UP4X supports DC input range of 48V to 54V.
   To avoid damage, please use the IGS-1000 Series under its specifications.

CAUTION

PWR1 and PWR2 must provide the same DC voltage while operating with dual power input.

Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the fault alarm contacts.

Note

1. The wire gauge for the terminal block should be in the range between 12 and 24 AWG.
2. Alarm relay circuit accepts up to 24V with a maximum current of 1A.

Grounding the Device

Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device.

NOTE

EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.

Installation

This section describes the functionalities of the Industrial Ethernet Switch’s components and guides you to installing it on the DIN-rail and wall. Basic knowledge of networking is assumed. Please read this chapter completely before continuing

Note

• The installation procedures of the IGS-1000-8T4X and IGS-1000-8UP4X are the same as those shown below.

DIN-rail Mounting Installation

Wall-mount Plate Mounting

•  The above pictures are for illustration only.

caution

You must use the screws supplied with the wall-mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty.

Product Specifications

Hardware Specifications
Copper Ports| 8 10/100/1000BASET RJ45 auto-MDI/MDI-X ports
PoE Injector Ports| —| 8 ports with 802.3bt PoE++ injector function (Ports 1 to 8)
__

SFP Slots

| 4 10GBASE-X SFP+ interfaces (Ports 9 to 12)

Backward compatible with 1000BASE-X and 2500BASE-X SFP transceivers

__

__

Connector

| Removable 6-pin terminal block Pin 1/2 for Power 1

Pin 3/4 for fault alarm Pin 5/6 for Power 2

__

Power Requirements

| 9~48V DC, 4A max.

Redundant power with reverse polarity protection function

| 48~54V DC, 8A max.

Redundant power with reverse polarity protection function

__

Power Consumption

| __

__

Max. 14.73 watts/50.2BTU

| Max. 8.69 watts/29.6BTU (System on)

Max. 387.2 watts/1320BTU (Ethernet + PoE Full Loading)

Dimensions (W x D x H)| 76 x 135 x 152 mm| 76 x 135 x 152 mm
Weight| 1213g| 1349g
Enclosure| IP30 aluminum case
Installation| DIN-rail kit and wall-mount kit
ESD Protection| 6KV
__

LED Indicators

| System:

P1, P2 (Green), Alarm (Red)

| System:

P1, P2 (Green), Alarm (Red)

Switch Specifications
Switch Architecture| Store-and-Forward
Switch Fabric| 96Gbps
Throughput (packet per second)| __

71.43Mpps@64bytes

Address Table| 16K entries
Buffer Memory| 12M bits on-chip buffer memory
Jumbo Frame| 9Kbytes
Flow Control| Back pressure for half duplex

IEEE 802.3x pause frame for full duplex

Power over Ethernet
PoE Standard| —| IEEE 802.3bt PoE++ PSE IEEE 802.3at PoE+ PSE
PoE Power Supply Type| —| 802.3bt, End-span+Mid-span
PoE Power Output| —| Ports 1 to 8: 95 watts max.
__

__

Power Pin Assignment

| __

__

—

| Pair 1 End-span: 1/2(-), 3/6(+)

Pair 2 Mid-span: 4/5(+), 7/8(-) 802.3bt: 1/2(-), 3/6(+),

4/5(+), 7/8(-)

---|---|---
__

PoE Power Budget (max.)

| __

__

—

| Single power input: 240W maximum

Dual power input: 360W maximum

Standards Conformance
Regulatory Compliance| FCC Part 15 Class A, CE
__

Stability Testing

| IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock)

IEC 60068-2-6 (vibration)

__

__

__

__

Standards Compliance

| IEEE 802.3 Ethernet

IEEE 802.3u Fast Ethernet IEEE 802.3ab Gigabit Ethernet IEEE 802.3z Gigabit SX/LX

IEEE 802.3ae 10 Gigabit Ethernet IEEE 802.3x Full-Duplex Flow Control

IEEE 802.3bt Power over Ethernet Plus Plus PSE IEEE 802.3at Power over Ethernet Plus PSE IEEE 802.3af Power over Ethernet Plus

IEEE 802.1p Class of Service

Environment
Temperature| Operating: -40 ~ 75 degrees C

Storage: -40 ~ 75 degrees C

Humidity| Operating: 5 ~ 90% (non-condensing)

Storage: 5 ~ 90% (non-condensing)

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQ resource at the PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team.
PLANET online FAQs:

• https://www.planet.com.tw/en/support/faq

Support team mail address:

• support@planet.com.tw

Copyright © PLANET Technology Corp. 2023. Contents are subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners.

FCC Warning

This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense

CE Mark Warning

This device is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

WEEE Warning

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>