NICREW UFO Aquarium Air Pump Instruction Manual
- August 27, 2024
- NICREW
Table of Contents
NICREW UFO Aquarium Air Pump
Safety Instructions
- To avoid possible electrical shock, do not immerse the pump in water. If the pump falls into the water, or otherwise becomes wet, do not reach for it until you have first unplugged it.
- To prevent possible electrical shock resulting from water back-siphoning, the pump should be used with a check valve or positioned.
- Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to get wet.
- Do not operate the appliance if it has a damaged cord or plug if it is malfunctioning, or if it is dropped or damaged in any manner.
- When removing filters, airstones, or air-operated ornaments from the aquarium, do not let the water run into the pump. Leave pump running and prevent back-siphoning by removing the open end of the tubing from the pump nozzle and taping it to the top frame of the aquarium.
- Always unplug appliances from an outlet when not in use. Never yank the cord to remove the plug from the outlet. Grasp plug and pull to disconnect
- Do not install appliances where it will be exposed to weather, or to temperatures below freezing.
- Read and observe all important notices on the appliance and in the product literature.
- To avoid getting the appliance plug or receptacle wet, position the aquarium to the side of a wall-mounted outlet. Arrange a “drip loop” for each cord connecting an aquarium appliance to an outlet. The “drip loop” is the part of the cord below the level of the outlet that prevents water from traveling along the cord and coming in contact with the outlet. (If using an extension cord, the “drip loop” is located below the level of the connector.) If the plug or receptacle gets wet, don’t unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug the appliance and examine the outlet for its presence.
Installation
- Installation 1
- Place the air pump on a shelf at least 30 cm (12″) higher than the water level of the aquarium, but not directly above the aquarium.NOTE: The shelf should have a raised edge to prevent the pump from sliding off.
- Installation 2
- Place the air pump on a surface lower than the water level of the aquarium. To avoid damage from accidentally spilled water, do not place the air pump directly below the aquarium. Use a check valve between the pump and the aquarium. It helps stop water from siphoning into your air pump in case of an electrical power failure or when removing filters from the aquarium.
- Installation 3
- Use the air pump with two ports for alternate installations.
NOTE: Use a T-connector (not included) with your two-port air pump for applications that require only one source of air. Place the pump on a separate surface from the tank.
- Use the air pump with two ports for alternate installations.
Maintainance
- Airflow loss is usually caused by clogged airstones, which over time become blocked as algae, floating debris, and mineral deposits accumulate in the pores. If you notice a diminished airflow, try blowing through the airstone yourself. If this is difficult, replace the airstone.
- If you replace the airstone in your filter(s) regularly you do not have to be concerned about loss of air due to clogged air stones.
- Worn diaphragms or other rubber parts can also diminish airflow.
- Clean the outside of the pump with a damp cloth and mild detergent.
- The pump mechanism never needs oil.
Disposal Information (for EU Countries Only)
The symbol shown as follows, applied to the product or its package, at the end of life, the product must not be thrown away, or disposed of into domestic waste!
Warranty
NICREW products carry a 12-month limited warranty from the date of purchase.
The warranty is limited to replacement or refund and does not cover loss of
aquarium life, personal injury, property lossor damage arising from the use of
the product. If your product is within warranty and you require a replacement
part or service,
please contact us at support@nicrew.com. For more
information, please visit www.nicrew.com.
Read User Manual Online (PDF format)
Loading......