Satellite Electronic 18054 CEILING FAN REMOTE CONTROL User Manual
- August 27, 2024
- Satellite Electronic
Table of Contents
Satellite Electronic 18054 CEILING FAN REMOTE CONTROL
Product Information
Specifications
- Model: Ceiling Fan Remote Control
- Function: Fan speed control, light control, dimming
- Compatibility: Suitable for ceiling fans with various bulb types
- Regulatory Compliance: FCC Part 15, IC licence-exempt RSS
Product Usage Instructions
Activating the Learning Process
Follow the instructions in the manual to set up the remote control for your
specific fan model.
Light Function Select Switch
Depending on the type of bulbs used in your fan
- If using CFLs or LED bulbs, slide the switch to the “O” position for on/off operation.
- If using incandescent bulbs or a dimmable LED array, slide the switch to the “D” position for dimming and on/off operation.
Wall Transmitter Operation
Use the transmitter to control the fan and light functions
- Press buttons 1-6 to set fan speed. The LED indicator will illuminate with each press.
- Press the designated off button to turn off the fan.
- Adjust the fan wind direction using the corresponding button.
- Control the light with the on/off button. To dim or brighten the lights, press and hold the dimmer button.
- Adjust the color temperature by pressing and holding the CCT button to your desired setting.
Installing Wall Control (Transmitter)
- Remove the wall plate and disconnect the existing toggle switch from the wall junction box.
- Connect the wires to the wall control unit using wire connectors.
- Secure the wall control unit with screws and attach the faceplate.
Regulatory Compliance
Ensure that any modifications or changes to the device are approved by the
relevant regulatory bodies to maintain compliance.
FAQ
-
Q: What should I do if the remote control is not working?
A: Check the battery in the remote control and ensure it is properly paired with the receiver. If issues persist, refer to the troubleshooting section in the manual or contact customer support. -
Q: Can I use this remote control with all types of ceiling fans?
A: The remote control is compatible with most ceiling fans, but ensure that your fan supports remote control functionality before installation.
CEILING FAN REMOTE CONTROL MANUAL
ACTIVATING THE LEARNING PROCESS
- Open the remote battery cover and install DC12V/A23 1pc battery, with the fan power off
- After installation is complete, AC power is turned on within 30 seconds, press and hold the LEARN button for 3 seconds. The receiver will make sound, Bi, twice The ceiling fan turns on 1 speed and the lights flash twice. This will indicate the receiver has learned the ID that was previously selected on the transmitter. Then the wall transmitter can control the receiver.
- If user cannot finish the setting within the 30 seconds time frame, the main power must be turned off and re-started again. This will reset the unit. Repeat step 1 until the LEARNING feature is activated as indicated.
DIP SWITCH – 0 & 1
0: All handsets and receivers are factory pre-set to the same channel. You can
operate the fan without doing a channel setting above but we recommend that
you set an individual channel for your fan.
1: This is to allow for each handset and receiver to be set on an individual
channel.
LIGHT FUNCTION SELECT SWITCH
If fan uses replaceable bulbs and CFLs or LED bulbs are used, please slide the Light Function Select Switch to “O” position for on/off operation. If fan uses replaceable bulbs and incandescent bulbs are used, or uses an integrated dimmable LED array, please slide the Light Function Select to “D” position for dimming/on/off operation.
WALL TRANSMITTER OPERATION
Press button 1~6 to set fan speed
When pressing remote button every time, the LED indicator would be on.
Press this button to turn the fan off.
Press this button to set fan wind direction up or down.
ON/OFF—Press this button and release instantly to turn on or off the light.
DIMMER—Press and hold to dim or brighten lights to the desired level and
release.
Press and hold to the desired CCT and release.
TRANSMITTER
Installing Wall Control (TRANSMITTER):
Remove wall plate, disconnect and remove the toggle switch from wall junction
box. Using the wire connectors, make the electrical connections to the wall
control (transmitter) unit. Carefully push all connected wires inside wall
switch box. Secure wall control unit with 2 screws previously removed. Face
plate could be locked onto the transmitter.
FCC
To assure continued FCC compliance
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18054
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>