PETLIBRO PLCT004 INFINITY Cat Tree User Manual
- June 12, 2024
- PETLIBRO
Table of Contents
PLCT004 INFINITY Cat Tree
Infinity Cat Tree 2
This product is for indoor use only. Please read this manual before using the product and keep it for future reference.
IN THE BOX
Notes
-
Make sure the A side of the base platform is facing upwards.
-
Please install the non-slip pads on the B side of the base platform, as shown in the diagram.
-
Make sure the A side of the platform is facing upwards.
-
The height of your cat tree after installation should not exceed 4 layers.
WARNING & CAUTIONS
- Place the cat tree indoors, away from direct sunlight or damp areas.
- Keep all tools and instruction in a safe place for future reference.
- This cat tree is intended for cat use only. Please keep children away.
- Keep all small parts away from children and pets to avoid choking hazards.
- Do not climb, rock, shake, step on, or hang on the cat tree.
- Place the cat tree on a flat, level surface for stability.
- Check the cat tree often for loose screws or parts that may need re-tightening.
- Do not place heavy items on the cat tree.
- Do not sit or stand on the cat tree.
- Inspect the cat tree for damage and discard if any part gets worn or damaged.
- Failure to follow the installation instructions in this manual may cause the cat tree to fall over and cause Injury.
Notes
- Do not install the scratching post to one of the side holes on the base platform.
- Do not attach the platform to one scratching post only.
KEY INSTALLATION METHODS
Scratching post+ scratching post
Insert the screw of one scratching post into the screw hole of another
scratching post, and rotate one of the scratching posts to tighten.
Scratching post + platform
Notes
- Make sure the A side of the platform is facing upwards.
- Make sure the platform fasteners are unlocked before installation.
- Align the cutouts of the platform with the connecting parts (grooves) of two scratching posts, and attach the platform to the scratching posts.
- Push the bottom platform fasteners towards the posts until the fasteners cannot be moved.
- If you can’t push the platform fasteners, try pressing around the cutouts on the platform while pushing thefasteners.
INSTALLATION STEPS
Base platform + base platform
Note
A. Place two base platforms side by side and align them.
B. Align two base platform connectors with the screw holes on the base platform. C. Insert screws into the holes and tighten with the hex key. D. Put the connector caps on the connectors.
Base platform + scratching post
Insert the screw of the scratching post into one of the base platform screw
holes (not the side holes) and rotate the scratching post to
tighten.
Scratching post + scratching post+ scratching post cap
A. Scratching post+ scratching post
Insert the screw of one scratching post into the screw hole of another
scratching post, and rotate one of the scratching posts to tighten.
B. Scratching post + scratching post cap
Insert the screw of the scratching post cap into the screw hole of the
scratching post and rotate the cap to tighten Scratching post +
platform
A. Align the cutouts of the platform with the connecting parts (grooves)
of two scratching posts, and attach the platform to the scratching posts.
B. Push the bottom platform
fasteners towards the posts until the fasteners cannot be moved. C. If you can’t push the platform fasteners, try pressing
around the cutouts on the platform while pushing the fasteners. Felt pad + platform
Place the pad on the platform and press it down to make sure the platform
surface is level. Cat bed + platform
A. Slide to install the cat bed fasteners to the cat bed.
B. Insert the fasteners under the bed into the holes on the platform.
C.
Rotate the fasteners 90 degrees.
Toy + platform
A. Insert the fastener of the toy into a corner hole on the B side of the
platform.
B.
Rotate the fastener 90 degrees. Scratching post+
scratching board
A. Slide to install the scratching board fastener to the back of
scratching board. B. Align the fastener of the scratching board to the
scratching post, and thread the strap with velcro through the buckle.
C. Secure the strap. Base platform + screw hole sticker
After installation, apply PVC stickers to the unused holes on the base
platform.
DIV POSSIBILITIES FOR REFERENCE
Notes
- If your cat tree does not look like any of the following examples, make sure the cat tree is stable after installa tion to avoid pet injury.
- Install the base of the cat tree first.
Do not install the cat tree as in the examples
below.
Or else it would be unstable and cause injury.
CARE AND MAINTENANCE
Cleaning the felt pad
- Do not use a washing machine.
- Do not use a brush to clean the pad.
- Do not place the pad in a dryer.
- Keep away from direct sunlight.
- Do not use a hairdryer to dry the pad.
- Do not use bleach for cleaning.
Cleaning the platform, scratching board, and scratching post
- To remove hair and dust, use a vacuum cleaner.
- Do not wash with water.
1. Dampen a soft cloth with soapy water.
2. Spot clean the stains and soiled areas with the cloth.
3. Air- dry the wet areas completely.
SPECIFICATIONS
Model | PLCT004 |
---|---|
Single-Layer Platform Load Capacity | 15kg / 33Ib |
Layer | 3 |
WARRANTY
- 12-month warranty
- For guidance on product use, please contact our customer service team via email: help@petlibro.com.
Let’s DIV for your cats!http://www.petlibro.com
INFINITY
Cat Tree 2
Model:
PLCT004
@Li bro Corp. All Rights Reserved.
Distributor:
Shenzhen Libra Technology Co., Ltd.
Address:
12/F, Tower B, GALAXY WORLD, Yabao Road,
Longgang District, Shenzhen, China
Manufacturer: Guangxi Gaofeng WuzhouWood-Based
Panel Co., Ltd
Address: Liutang, Wutang Town, Xingning District,
Nanning, Guangxi, China
Certificate No. BJ/EPA/2020/06/1001
Made in China
PLCT004_V1.0
Documents / Resources
|
PETLIBRO PLCT004 INFINITY Cat
Tree
[pdf] User Manual
PLCT004 INFINITY Cat Tree, PLCT004, INFINITY Cat Tree, Cat Tree, Tree
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>