Satellite Electronic 2AQZU DC Power Ceiling Fan Remote Control Instruction Manual
- June 10, 2024
- Satellite Electronic
Table of Contents
CEILING FAN REMOTE CONTROL MANUAL
LEARNING PROCESS
NOTE: The Hand Held Remote Control System is equipped with a learning
frequency function which has code combinations to prevent potential
interference from other remote units.
Step: 1. Install 2pcs DC1.5V/AAA batteries. Within 30 seconds of turning the
receiver AC power ON. Press the transmitter’s LEARN button.
Step: 2. Hold LEARN button over 5 seconds. Once the receiver has detected the
frequency, the ceiling fan would turn on low speed. This will indicate the
receiver has learned the frequency that was previously selected on the
transmitter.
NOTE: After the AC power is on, do not press any other button on the
transmitter as doing pairing. Because it might be to cause the procedure to
fail.
After completing the steps above, you should be able to operate the ceiling
fan. If the fan is not responding to the transmitter, please turn the power
off to the receiver. And
repeat step 1 and 2. NOTE: Remove the battery if not used for long
periods of time to prevent damage to the hand held remote.
LIGHT FUNCTION SELECT SWITCH
If fan uses replaceable bulbs and CFLs or LED bulbs are used, please slide the Light Function Select Switch to “O” position for on/off operation. If fan uses replaceable bulbs and incandescent bulbs are used, or uses an integrated dimmable LED array, please slide the Light Function Select to “D” position for dimming/on/off operation.
FUNCTIONS OF TRANSMITTER
-
FAN SPEED：
1: Turn on ceiling fan at 1st speed (lowest speed)
2. Turn on ceiling fan at 2nd speed
3. Turn on ceiling fan at 3rd speed
4. Turn on ceiling fan at 4th speed
5. Turn on ceiling fan at 5th speed
6. Turn on ceiling fan at 6th speed (high speed)
****: Turn off ceiling fan. -
FAN TIMER: When the fan turned on. 1H ：Setting up that the ceiling fan will turn off after 1 hour automatically.
3H ：Setting up that the ceiling fan will turn off after 3 hours automatically.
6H ：Setting up that the ceiling fan will turn off after 6 hours automatically. -
:set fan wind direction up or down.
-
— Natural breeze: Fan speed will modulate to simulate a natural breeze.
-
:Press and turn the light on or off. Press and hold to dim or brighten light to the desired level and release.
-
: Press for color-temperature change setting
Installation of Transmitter Wall Mount Holder with Two screws.
To assure continued FCC compliance
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. –Consult the dealer or an experienced radio/TV
technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18041
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.