Satellite Electronic 2AQZU-18049 Ceiling Fan Remote Control Instruction Manual
- June 15, 2024
- Satellite Electronic
Table of Contents
CEILING FAN REMOTE CONTROL MANUAL
ACTIVATING THE LEARNING PROCESS
- After installation is complete, AC power is turned on within 30 seconds, press and hold the LEARN button for 3 seconds. The receiver will make sound, Bi, twice The ceiling fan turns on 1 speed and the lights flash twice. This will indicate the receiver has learned the ID that was previously selected on the transmitter. Then the wall transmitter can control the receiver. 2. If user cannot finish the setting within the 30 seconds time frame, the main power must be turned off and re-started again. This will reset the unit. Repeat step 1 until the LEARNING feature is activated as indicated.
DIP SWITCH – 0 & 1
0: All handsets and receivers are factory pre-set to the same channel. You can
operate the fan without doing a channel setting above but we recommend that
you set an individual channel for your fan.
1: This is to allow for each handset and receiver to be set on an individual
channel.
WALL TRANSMITTER OPERATION
Press button 1~6 to set fan speed
Press this button to turn the fan off.
Press this button to set fan wind direction up or down.
ON/OFF—Press this button and release instantly to turn on or off the light.
DIMMER—Press and hold to dim or brighten lights to the desired level and
release.
Press and hold to the desired CCT and release.
When pressing remote button every time, the LED indicator would be on.
: Pull out for turning off AC power
TRANSMITTER Installing Wall Control (TRANSMITTER):
Remove wall plate, disconnect and remove the toggle switch from wall junction
box. Using the wire connectors, make the electrical connections to the wall
control (transmitter) unit. Carefully push all connected wires inside wall
switch box. Secure wall control unit with 2 screws previously removed. Face
plate could be locked onto the transmitter. 
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID: 2AQZU-18049
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>