Satellite Electronic 2AQZU-18051 Ceiling Fan Remote Control Instruction Manual

Satellite Electronic 2AQZU-18051 Ceiling Fan Remote Control

Product Information

Specifications:

• Model: TRD047S1M
• FCC ID: 2AQZU-18051
• Power Source: DC3V CR2032 1pcs battery
• Functions: Fan control, light control, fan speed adjustment, fan timer, wind direction control, natural wind mode

Product Usage Instructions

Learning Process:

1. Open the battery cover of the remote and insert one DC3V CR2032 battery.
2. Within 30 seconds of turning on the AC power of the receiver, press and hold the remote’s LEARN key for over 5 seconds.
3. Once the receiver detects the frequency, it will make a sound (Bi Bi) twice to indicate that it has learned the frequency from the transmitter.
4. Note: Do not press any other button on the transmitter before setting learning. Pressing other buttons may cause the procedure to fail.
5. If the fan is not responding to the transmitter, turn off the power to the receiver, and repeat steps 1 and 2.
6. Note: Remove the battery if the remote will not be used for long periods of time to prevent damage.

Functions of Transmitter:

1. To turn off the fan.
2. Press this button to increase fan speed. The LED indicator will be on the corresponding position of the fan speed (1~6 speed).
3. Press this button to decrease fan speed. The LED indicator will be on the corresponding position of the fan speed (1~6 speed).
4. Press this button to set up the fan off time.
5. To set the fan wind direction up or down.
6. To set the fan in natural wind mode, press the button to automatically change the fan speed.
7. Press this button shortly to turn on and off the light. Press and hold this button for a long time to dim the light.
8. If the LED indicator on position 1 does not turn on when pressing a remote button, replace the battery with a new DC3V CR2032 battery.

FAQ

To assure continued FCC compliance:

CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

LEARNING PROCESS

NOTE ： The Hand Held Remote Control System is equipped with a learning frequency function which has code combinations to prevent potential interference from other remote units

• Step: 1 Open the remote battery cover and install DC3V CR2032 1pcs batteries
• Step: 2 Within 30 seconds of turning the receiver’s AC power ON.
• Step: 3 Press and hold the remote “LEARN” key for over 5 seconds, once the receiver has detected the frequency, the receiver will make a sound, Bi Bi, twice. This will indicate the receiver has learned the frequency that was previously selected on the transmitter.

NOTE: After the AC power is on, do not press any other button on the transmitter before setting learning. Doing so will cause the procedure to fail. After completing the steps above, you should be able to operate the ceiling fan and light. If the fan is not responding to the transmitter, please turn the power off to the receiver. And repeat step 1 and 2.
NOTE: Remove the battery if not used for long periods of time to prevent damage to the handheld remote

FUNCTIONS OF TRANSMITTER

1. To turn the fan off.
2. Press this button to increase fan speed and LED indicator will be on the position of fan speed. (1~6 speed)
3. Press this button to decrease fan speed and the LED indicator will be on the position of fan speed.(1~6 speed)
4. FAN TIMER: Press this button to set up the fan off time .
5. To set fan wind direction up or down.
6. To set fan in natural wind mode, press the button for set fan speed change automatically
7. Press this button shortly to turn on and turn off the light, and press and hold this button for long time to dim the light.
8. When pressing remote button, the LED indicator on position 1 would be on. If you press the remote button and
   LED indicator would not be on, you should change new DC3V, CR2032 1pcs batteries.

To assure continued FCC compliance:

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

To assure continued FCC compliance:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

• Model: TRD047S1M
• FCC ID: 2AQZU-18051

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>