EAE KNX Rosa Switch Installation Guide
- August 15, 2024
- EAE
Table of Contents
EAE KNX Rosa Switch
Specifications
- Type of protection: IP 20
- Safety class: II
- KNX Supply Voltage: 21 V to 30 V DC SELV
- Current Consumption: 10 mA
- Installation Temperature range: 60×60 mm standard box Ambient Storage
- Humidity: Max. air humidity 95%, no moisture
- Dimensions: Front face (85×85 mm), Side-Surface of plaster (11 mm), Side-Under plaster (19.4 mm)
- Weight: 93 g
- Material: Metal, Aluminum
Product Usage Instructions
Commissioning
- The device default physical address is 15.15.255. Use Engineering Tool Software (ETS5 or higher) to determine the physical address and set parameters.
- Import the .knxprod file to the ETS. Refer to the Product Manual for detailed parameter configuration.
Cleaning
If the device becomes dirty, use a dry cloth for cleaning. Avoid using wet
cloths, caustics, or solvents.
FAQ
Q: Can the device be operated in open enclosures?
A: No, the device may only be operated in closed enclosures such as
distribution boards.
Q: What is the maximum number of addresses supported by the device?
A: The device supports a maximum of 254 addresses.
Installation Manual STx Switch EAE KNX Rosa Switch Series
Operation and Display
- Touch Button groups
- KNX Port Terminal
- Programming Button
- Programming LED
Description of the Device
- Serial switches with plastic push-button
- Can be configured with ETS5 or higher
- Independent button configuration for each fold
- Integrated Temperature Sensor (°C/°F) (Optional)
- Integrated Humidity Sensor (Optional)
- Different color options
- Cleaning mode function
- Logical function
- Dependent or independent programmable buttons.
- 60×60 mm easy mounting to standard junction boxes.
- 4 rockers can be programmed to perform different functions
- Switching
- Dimming
- Shutter/Blind
- Value
- Scene control
- Status notification
Technical Data
Installation
Installation of the product is done with the help of the flange which is inside the box. The flange is fixed to the junction box by using screws while the arrows on flange are headed to up. The switch is placed into the junction box by positioning the EAE logo upwards and then reclining it to the flange. The switch is slowly turned clockwise to give the right position to it on the flange. After the clicks are on the right position, switch is turned counter- clockwise to lock it on the flange.
Commissioning
- Device default physical address is 15.15.255. Determination of the physical address and setting of parameters are actualized with Engineering Tool Software (ETS5 or higher). “.knxprod” file must be imported to the ETS. ( http://www.eaetechnology.com/ )
- A detailed information about parameter configuration can be found in Product Manual of device.
- Installation and commissioning of device may only be implemented by trained electricians. The relevant standards, directives, regulations and instructions must be observed when planning and implementing the electrical installation.
- When connecting the device make sure that the device can be isolated!
- Protect the device against moisture, dirt and damage during transport, storage and operation!
- Do not operate the device out of the specified technical data which is stated.
- The device may only be operated in closed enclosures (Distribution boards)
Cleaning
If device becomes dirty, only a dry cloth can be used for cleaning. İt is not suitable to use wet cloths, caustics and solvents.
© EAE Technology
Ikitelli Org.San.Bolg. Ziya Gokalp Mah. Eski Turgut Ozal Cad. No: 20 34490
Basaksehir/Istanbul Tel: +90 212 549 97 13
References
- EAE Technology – KNX Akıllı Ev Sistemi, Aydınlatma Otomasyonu
- EAE Technology – KNX Akıllı Ev Sistemi, Aydınlatma Otomasyonu