somfy 1860105 Animeo Motor Controller Installation Guide

: August 13, 2024
: somfy

Table of Contents

A : MOUNTING
B : WIRING
C : CONFIGURATION
D : SYMBOLS
CHARACTERISTICS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**somfy 1860105 Animeo Motor Controller Installation Guide

**

Before installation, please read and follow these instructions. Incorrect installation may lead to serious injury. Disconnect all power cables to be installed! Take precautions against unintentional switching on! The product must be installed, maintained and dismounted by a skilled person according to the relevant regulation. An allpole mains switch shall be incorporated in the electrical installation of the building to provide simultaneous separation of at least 3 mm for all phases from the supply. Somfy cannot accept any liability for defects and damage caused by failure to follow these instructions. Please keep these instructions for future reference.

SOMFY hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the European Directives applicable to the European Union. A declaration of conformity is available at www.somfy.com/ce.

www.somfy.co.uk

A : MOUNTING

Choose the optimum location: flat and large surface.
Mount the Motor Controller
Use cable tie!
Keep to minimum distance!

`B : WIRING`

Wiring diagram
Tool for all terminals
Check the correct running direction of the end products

UP: All end products move upward
STOP: All end products stop
DOWN: All end products move downwards

Possible switches
Smoove Origin IB, ref. 1811272
Double push button unlocked

C : CONFIGURATION

Reset/Prog button
With this button, you can access the basic configuration of the motor controller.
Green LED = Blinks, when no RTS module exists
Yellow LED = Screen Mode
Orange LED = Venetian blind EU mode
Red LED = Venetian blind US mode
LED flashes = no running time existing
LED glows = running time stored
Selection of motor, electronic or standard
Preset motor type is Electronic Motor (ELM) Somfy TLW25 WT. Switching to standard motor (STM) Somfy LV/LW25 is possible.
Entering the programming mode.
To toggle between modes, press shortly the Reset/Prog button. Repeat until desired LED lights up.
Save and exit.
Using a prohibited functional mode can damage the motors! The mode is specified for all 4 motor outputs!
Selection of switch ergonomics
The different ergonomics are described in the
manual:

  * Screen ergonomics (SCR)
  * Venetian blind with EU ergonomics
  * Venetian blind with US ergonomics (default mode)
  * Entering the programming mode.
    1. To toggle between modes, press shortly the
    2. Reset/Prog button. Repeat until desired LED lights up.
    3. Save and exit.

Factory reset
Learn running time/length
Move screen to upper end limit
Press Stop until screen moves down on its own
Press Stop when lower end limit is reached

D : SYMBOLS

Actions
Up
Down
Stop
End product status
Up movement
Down movement
Upper end limit
Lower end limit

CHARACTERISTICS

Supply voltage	220 – 230 V AC / 50/60 Hz ~
Stand-by current (IEC 62301)	17 mA@230 V AC
Stand-by power (IEC 62301)	0,49 W@230 V AC
Supply voltage KNX bus	KNX voltage 21…30 V DC, SELV
Rated current consumption KNX	As per KNX guidelines, 10 mA
Supply voltage group control input	SELV, 16 V DC ⎓
Supply voltage local push buttons	SELV, 16 V DC ⎓
Max. motor current consumption	4 x 0.6 A@24 V DC; max. 1 motor per output
External overcurrent protection	16 A fuse required
Outputs	Short circuit protected
Without contact gap	Semiconductor switching device: ɛ
Terminals	Spring connectors
Terminals KNX	KNX bus terminal (black/red)
Running time per output	Max. 5 minutes
Operating temperature	– 5° C … 50° C
Relative humidity	Max. 85 %
Material of housing	PC-ABS
Housing dimensions	180 x 255 x 61 mm
Weight	765 g
Protection class	II
Degree of protection	IP 20
Overvoltage category	III
Pollution degree	2
Conformity	www.somfy.com/ce

CABLES

Connection to …| Cable| Twisted pair| Max. length| Stripping length
---|---|---|---|---
Motors| Min.: 3 x 0.28 mm²/22 AWG Max.: 3 x 2.5 mm²/13 AWG| | 20 m/66 ft| 9…10 mm/0.35…0.39″
Switch| Min.: 3 x 0.28 mm²/22 AWG Max.: 3 x 2.5 mm²/13 AWG| Recommended| 100 m/330 ft| 9…10 mm/0.35…0.39″
Group control| Min.: 3 x 0.28 mm²/22 AWG Max.: 3 x 1.5 mm²/15 AWG| Recommended| 50 m/165 ft| 9…10 mm/0.35…0.39″
KNX bus| Min.: 3 x 1.5 mm²/15 AWG Max.:3 x 2.5 mm²/13 AWG| | | 9…10 mm/0.35…0.39″

We care about our environment. Do not dispose of the appliance with usual household waste. Give it to an approved collection point for recycling.

Somfy Activites SA
50 Avenue du Nouveau Monde
74300 Cluses
France
www.somfy.com/projects A BRAND OF SOMFY GROUP
ã2024, SOMFY ACTIVITIES SA. ALL RIGHTS RESERVED. REF. 5172914A – 2024/01/17