SUNBRITE SB-WM-F-XL-BL Weatherproof Universal Fixed and Tilt Mounts for Very Large Displays Installation Guide
- June 9, 2024
- SUNBRITE
Table of Contents
SUNBRITE SB-WM-F-XL-BL Weatherproof Universal Fixed and Tilt Mounts for
Very Large Displays
Warnings
Installation by a qualified professional is highly recommended for this product. Do not begin installation until you have thoroughly read and understand these instructions. This mount supports displays up to VESA 1000×700, and a maximum load of 250 lbs (113.6 kg). Ensure the wall can safely support four times the combined weight of the mount and display. The manufacturer does not accept responsibility for incorrect installation.
Specifications
- Maximum Load: 250 lbs (113.6 kg)
- Forward Tilt Range: -8° / +13°
- Horizontal Tilt Range: +5°
- Dacromet Coated Assembly
- Stainless Steel Mounting Hardware
Box Contents
- Wall Plate (1)
- Left Arm (1)
- Right Arm (1)
- Hex Wrench (1)
- Security Wrench (1)
- Hardware Kit
Tools Required
- Power Drill
- 1/4″ & 3/8″ Drill Bits
- Level
- 1/2″ (13mm) Wrench
- Stud Finder
- Phillips Screwdriver
Hardware Kit
- Bag 1: TV Arm Mounting
- Bag 2: TV Arm Mounting
Installation
Caution: Overtightening bolts can damage the bolts and reduce their holding strength.
Mount the Wall Bracket
Pro Tip:
The wall bracket features a screw slot for temporary placement to help mark
pilot holes.
For Mounting on a Stud Wall
Use a stud finder to locate your studs. Drill two pilot holes each into three
wood studs using a 1/4″ drill bit. Drill into the center of the studs at least
2-1/2″ deep.
Insert six lag bolts and washers through the wall plate into the pilot holes and tighten.
For Mounting on a Concrete Wall
Drill anchor holes into the concrete using 3/8″ drill bits to a depth of
2-1/2″. Insert concrete wall anchors and tap in with a hammer. Ensure the
anchors are embedded entirely within the concrete. Insert four lag bolts (U)
into the wall anchors through the wall plate. Tighten all bolts.
- Caution: Concrete must be a 2000 psi density minimum. Lighter-density concrete may not hold concrete anchors. The cinder block must meet ASTM C-90 specifications.
- Caution: Before drilling, verify the concrete is at least 1-3/8″ thick. Mount in a solid part of the block, generally 1″ minimum from the side of the block. Do not drill into mortar joints. Use a standard electric drill on a slow setting. Do not use a hammer drill to avoid damage.
Mount Arms to TV
- Determine the screw size that fits your TV by carefully hand-threading them into the threaded insert on the rear of the TV. If there is any resistance, stop immediately.
- Thread the screw through the washer, arm, and spacer (if needed), and into the TV. Spacers are commonly needed on TVs with curved backs or recessed screw inserts.
- Ensure the arms are installed flat side to the TV and square to each other after all screws have been installed.
Hang the TV on the Wall Plate
Carefully lift the TV to hook the arms over the top lip of the wall plate. Allow the lower portion of the arms to swivel in under the bottom lip of the wall plate. Do not release the TV until it is completely seated.
Adjustments
Forward Tilt Adjustment (SB-WM-T-M-BL only)
- Using the included long hex wrench, loosen the tilt adjustment locks (circled) on the sides of the arms enough to allow movement.
- Set the tilt to the desired angle, then tighten the locks. If the locks cannot be tightened enough, remove the TV from the wall for better access.
Horizontal Adjustment
The arms feature tilt adjustment screws to help fine-tune the display’s
alignment. Use provided hex wrench to adjust the screw for perfect leveling.
Pro Tip:
Due to the displayed weight, it may be easier to lift the panel slightly while
adjusting the screw.
Locking
To lock the arms to the wall bracket, twist the locking tabs until the edge
catches behind the bracket. The hex wrench can be used as a tool to help with
this step. Add a padlock (not included) if desired.
Technical Support
For technical support, please call 866-357-8688 or visit https://www.sunbritetv.com/support/services/contact-support, fill out the support request form, and our support team will respond via email. Visit tech.control4.com/technician for discussions, instructional videos, news, and more.
Warranty and Legal Notices
Find details of the product’s Limited Warranty and other resources such as regulatory notices and patent and safety information, at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
Copyright ©2022, Snap One, LLC. All rights reserved. Snap One and its respective logos are registered trademarks or trademarks of Snap One, LLC, in the United States and/or other countries. Control4 and SunBriteTV are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks. Information within this specification is subject to change without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>