AUDIO A10-RX Digital Wireless Receiver User Guide

A10-RX
Digital Wireless Receiver
— User Guide —

Copyright/Doc Rev History Info

Model A10-RX
Copyright © 2022 Sound Devices All rights reserved

Certifications
July-18| Revised Firmware Update procedure for A10-RX-SL
Nov-18| Added v2.50 change (i.e. User Groups)
June-19| Added v2.70 changes (A10-TX Muted, and Standby Mode displays)
Jan-20| Updates for v2.80 (green and red LED indications)
Mar-20| Updates for v2.90 (New RF overload indicator, conform to CSV)
Feb-21| Updates for v3.00 (Support for A-15PIN accessory)
July-21| Updates for v4.00 (Support for A20-Mini)
April-22| Updates for v5.00 (Modulation menu and Q-meter)
June-22| Updates for v5.10 (Q-meter display options)

Overview

• Two-channel, wideband receiver a with worldwide tuning range of 470 MHz – 694 MHz
• Advanced Digital Diversity topology uses two complete RF receivers for each of the two channels, with four RF receivers in total
• State-of-the-art 100% digital long-range modulation delivers the longest transmission distance of any system on the market
• Simple menus are quick to access
• Available in both slot (Uni-/SuperSlot) with the A10-RX-SL or stand-alone cabled version with the A10-RX-XLR
• Analog line-level or AES3 digital audio output
• Compatible with select Sony camera models with A-15PIN This collaboration between Sony and Sound Devices allows the A10-RX receiver to pass two-channel digital audio internally on the Sony camcorder, negating the need for any external cables.

Digital wireless for today and tomorrow.
The A10 Digital Wireless System is designed for the technical demands and requirements of today’s RF-hostile, multi-channel productions The A10-TX and A20-Mini  digital transmitter and A10-RX two-channel receiver deliver broadcast-quality audio and reliable digital RF performance with an easy, multi-system setup The A10’s proprietary digital RF topology and Advanced Digital Diversity System is the result of years of research, laboratory experimentation, and customer experience The result is a wireless link with full 20 kHz audio bandwidth, high dynamic range, ultra-low distortion, an extremely low 2-millisecond end-to-end delay in Standard modulation The  A10 System allows the user to operate up to 20 channels in an 8 MHz TV channel, maximizing spectrum efficiency.
With firmware version 5.00, the A10/A20 Wireless System delivers the longest transmission distance of any system on the market ¹ The state-of-the-art, 100% digital long-range modulation offers the same great audio quality (10 Hz – 20 kHz) as our Standard modulation scheme with a longer range for both line-of- sight and heavy multipath transmission The A10-RX two-channel Advanced Dual Diversity receiver is a portable, all-digital wireless receiver for the A10 System It is designed to work with one or two  A10-TX or A20-Mini transmitters. It offers 224 MHz switching bandwidth and precision RF tracking filters in a lightweight, robust package Two models are available, the A10- RX-SL for slot-in connection and the A10-RX-XLR for stand-alone operation with hardwired power and audio connections.
¹ When comparing systems the with same transmit  power, same antennas, and same transmission frequency

System Quickstart

The A10 Digital Wireless System is easy to use Follow the steps below for basic setup and operation
At the Receiver

1. Fit the included straight and right-angled antennae to the A10-RX receiver
2. Connect the receiver to a power source It will immediately power on
3. Using the scanning tool in the Selection menu find an available open frequency. If multiple wireless systems are in use, make certain to keep frequenat cies least 400 kHz apart.
4. Connect the audio output from channel 1, channel 2, or both to an audio input on a mixer, recorder, camera, or PA system
5. Ensure that the receiver audio output type and level are set based on the input type.

At the Transmitter

1. Attach the straight antenna to the A10-TX or A20-Mini
2. Attach an audio source to the 3-pin LEMO input connector
3. Insert batteries into the A10-TX or A20-Mini battery compartment and power on the unit with the red On/Off button
4. Set the audio input type to set to match the connected input
5. Set the modulation and transmitting frequency on the A10-TX or A20-Mini (using A20Remote) to match the modulation and frequency set on the A10-RX receiver channel.
6. With A10-TX adjust the audio gain according to your environment and source, taking care not to overload the signal This is indicated by a red LED The A20- Mini’s GainForward feature eliminates the need to adjust microphone preamplifier gain at the wireless transmitter

At the Receiver

1. Confirm that the Channel Power LED is solid blue.
2. Confirm that the RF Status LEDs and display indicate good RF strength.
3. For A10-TX, confirm that the audio level at the receiver corresponds to the audio connected to the A10-TX input
   For A20-Mini, adjust the A10-RX input gain according to your environment and source
   When the A10-RX is connected to the 688, 833,888, or Scorpio via the SL-2 or Sthe L-6, A10-RX input gain is bypassedthe and audio gain is adjusted from mixer-recorder 4 The  system is now ready for use

Connectors, Controls Description

1. Antenna Socket
   SMA connector, 50 ohm, connectthe to included 1/4-wave whip antenna

2. Channel Power LED
   • Illuminates blue when the channel’s receiver circuitry is powered and operational
   • Blue LED flashes when paired transmitter’s battery is critically low or depleted

3. Green/Red RF Status LEDs
   • Indicates signal strength of received RF
   • Green LED illuminates solid green with good RF reception. It starts to flicker green as the received RF signal quality deteriorates
   • Red LED illuminates solid red when the receiver loses lock to the transmitter signal due to a weak signal or the transmitter being turned off
   • Both green and red LEDs are off at the fringe of the reception
   • Both green and red LEDs flash when RF overload is occurring

4. Left Button
   Moves the selection n in the menu to the left, or decremthe ents values

5. Menu/Select Button
   Enters the menu selection Also used to select options in the menu

6. Right Button
   Moves the selection in the menu to the right, or increments values

7. Antenna Socket
   SMA connector, 50 ohms, connect to the included 1/4-wave whip antenna

8. Display
   OLED screen The screen can be set to turn off after a period of inactivity from the Selection menu (Main > Settings > Screensaver)

Powering

The A10-RX-SL receives power over its D-sub connector The A10-RX-XLR receives power from its 4-pin Hirose female connector, The male Hirose connector is a power loop through When DC power is present, either at the D-sub connector or the Hirose 4-pin, the A10-RX is powered There are no additional power switches
Channel Powering
Each of the two channels of the A10-RX can be powered on or off individually When a channel is powered down that portion of the A10-RX no longer draws power If the  A10-RX is going to be used for a single wireless channel, the best practice is to power down the unused channel Channel power is controlled in the Selection Menu (Main >  System > Power) 

Shortcut: To power off RX1, simultaneously hold the Left and Centre Menu buttons down for two seconds. To power off RX2, simultaneously hold the both Right and Centre  Menu buttons down for two seconds. Repeat to turn the individual channels back on. If both RX channels are powered off, the A10-RX will enter standby mode. Press the  Centre button to turn both channels of the RX back on simultaneously.

Channel Power LEDs
The A10-RX has blue Channel Power LEDs for each of its two channels. When first powering the A10-RX without transmitters present, the LEDs illuminate indicating the  receiver channel is powered
The receiver channel will connect, or pair, to an A10-TX or A20-Mini transmitter that is powered on and set to the receiver frequency The Channel Power LED then shows the  battery status of its associated transmitter

• Solid Blue – a solid blue LED indicates that the transmitter battery is in good condition
• Flashing Blue – a flashing blue LED indicates when the transmitter battery level is low or depleted
  When a paired transmitter is powered down, the blue LED continues to show the last condition of the transmitter battery If the transmitter is powered back on, or a new  transmitter is activated on the channel, that transmitter pairs with the receiver and its transmitter battery condition is shown with the blue LED
  The LEDs change assignment based on the orientation of the display. Channel 1 is always shown left of the display and channel 2 is always on the right.

Main Display

When the receiver is first powered on, the main display is in a two-channel view.
Two-Channel View
The display shows channel 1 and channel 2 simultaneously Parameters displayed include the RF signal strength at each antenna, Q-meter, receiver frequency, audio level, and  transmitter battery level

1. Channel 1 Status
   Displays Channel 2 RSSI, Q-meter, audio level, frequency, and transmitter information

2. Channel 2 Status
   Displays Channel 2 RSSI, Q-meter, audio level, frequency, and transmitter information

3. RSSI Meter
   Bars indicate RF signal strength at each antenna for the selected frequency
   Note: Even with the transmitter turned off or out of range, bars may still be displayed This is due to the presence of the background RF signal at the selected frequency

4. TX Battery Status
   Battery icons indicate the status of transmitters’ batteries

5. Q-meter
   The Q-meter displays the difference between the signal from the transmitter and any interference using five circles. When a frequency without little to no interference is selected, the Q-meter will display five bars.

6. Audio Level
   Each channel shows a horizontal meter for audio levels

7. Frequency/TV Channel
   Displays the receiver frequency Region, channel, and sub-channel are displayed when the Display Options menu is set to TV Ch X, Y, and Z regions are selected by the TV  Channel Map setting. An asterisk next to the subchannel indicates that the set frequency is not directly on a preassigned subchannel.
   The User Name is displayed when User Groups are active See User Groups

8. Transmitter Record Status
   The Record indicator is displayed when the tuned transmitter is recording

9. Transmitter Limiter/Overload/Mute
   Displays the Limiter, Overload, or Mute status of the tuned transmitter L = Limiter,! = Overload, M = Mute

Single-Channel View
Pressing the Left or Right buttons when in a two-channel view changes the display to a single-channel view of channel 1 or 2, respectively.
In addition to the parameters shown in the two-channel view, the single- channel screens display the analog output level or AES and the transmitter name.

When the channel is paired with an A10-TX, pressing the Left or Right button again shows the A10-TX metadata

When the channel is paired with an A20-Mini, pressing the Left or Right button enters the A10-RX Input menu The Input Menu is not available when the A10-RX is connected  to the 688, 833, 888, or Scorpio via the SL-2 or SL-6 With this setup the A20-Mini metadata screen is displayed See GainForward Input Menu for more details.

Mute Function on the Transmitter
When the A10-TX or A20-Mini audio is muted from the transmitter, the A10-RX displays ‘M’ in the dual channel screen and ‘Mute’ in the single channel screen.

RF Signal Indicator LEDs
The RF Signal LEDs offer an at-a-glance indication of RF performance The LEDs to the left of the display indicate channel 1 activity, while the LEDs to the right indicate  channel 2 activity Each channel has one green LED and one red LED

• Green LED only – illuminates solid green with good RF reception. It starts to flicker green as the received RF signal quality deteriorates
• Red LED only – received RF signal quality is deteriorating
• Both green and red LEDs flash when RF signal is overloading/too strong.
• Both green and red LEDs are OFF at the fringthe of reception

The LEDs change assignment based on the orientation of the display set in Menu

Settings > Display > Orientation. Channel 1 is always shown left of the display and channel 2 is always on the right.
The LEDs can be turned off in Menu > Settings > LEDs.
RF Overload Indication.
When RF signal is overloaded, the A10-RX’s green and red LED flash. If you see this indication the RF signal is too strong Correct the situation by reducing RF power on the  transmitter, increasing the distance between transmitter and receiver, or applying attenuation to the antenna system in use
Display Orientation
The A10-RX Menu screen operates with its Menu buttons either below or above the display This is controlled in Menu > Settings > Display > Orientation
Q-meter vs Audio Meter Display Size
The A10-RX displays a large Q-meter by default The Q-meter can display smaller making room for a larger Audio meter Set your preferred size in Menu > Settings > Display > Q-Meter

GainForward Input Menu (A20-Mini only)

The A10-RX supports the A20-Mini’s GainForward feature GainForward eliminates the need to adjust microphone preamplifier gain at the wireless transmitter. Audio levels  from the transmitter are controlled either directly at the mixer’s trim control or at the wireless receiver If the talent speaks too softly or emotes too loudly after being “wired”  with the transmitter, simply adjust the transmitter gain with the mixer’s gain trim Read more about GainForward at: https://www.sounddevices.com/gainforward-explained/
From the A10-RX home screen, press the channel’s arrow button twice to enter the Input menu.
From the Input menu, press the middle button to select a sub-menu to adjust gain, low cut, or limiter of the incoming A20-Mini transmitted signal.
When the A10-RX receiving A20-Mini signal is slotted into the SL-2 or SL-6, the A10-RX Input menu settings are bypassed and hidden All gain, low cut, and limiter activity are  performed and controlled by the 688, 833, 888, or Scorpio See the Mixer-Recorder User Guides for more information
The A10-TX does not support GainForward. The Input menu is not available on channels paired with an A10-TX.

Input Menu (A20-Mini only)

• 40 Hz
• 60 Hz
• 80 Hz
• 100 Hz
• 200 Hz
limiter| | Sets the Limiter of the incoming A20-Mini signal.| • On
• Off
Information| | Displays the paired A20-Mini’s name and the AIO-RX’s Input Gain and Low Cut values.|

Selection Menu

The A10-RX receiver is controlled through its main Selection menu. Enter the menu by first selecting either the channel 1 receiver (Left button) or channel 2 receiver (Right button), then press the Centre Menu button Once in the menu, the Left and Right buttons toggle among options and the Menu button makes the selection.
Main Menu

Selections| Icon| Description| Channel or Global| Options
---|---|---|---|---
Exit| | Returns to the main display screen.| |
Frequency| | Sets the transmitter’s frequency. Frequency selection and channel increments change based on the region of operation to which the unit is set.| Channel| •TV Channel Increments
•Sub Channel Increments
•Tune: Frequency Increments in 25 kHz steps
Outputs| | Enters the Outputs sub-menu.| | •Maximum Level
•Audio Polarity
•Mode
•Test Tone
Scan| | Enters the scan function. The scanner indicates the RF activity. Scans can either be in 25 MHz increments or across the full range of the receiver.| Global| •I-10 – scans subsections of the tuning range
•Full – scans entire tuning range of the system
Privacy| | When active the transmitter sends its signal encoded with a four- digit privacy key set at the transmitter. The same four-digit key needs to be set on a receiver to receiver to receive the signal.| channel| • On-enter key
•Of – encryption cleared, set to 0000 to deactivate
Settings| | Enters additional settings sub-menu.| | •Modulation
•User Groups
•TV Channel Map
•Display
•LEDs
System| | Enters additional settings submenu| | •Power
•Restore
•Info

Outputs Sub-Menu

Selections| Icon| Description| Channel or Global| Options
---|---|---|---|---
Exit| | Returns to the main menu| |
Max Level| | Selects the maximum analog output level. Output level based on a 0 dBFS signal sent from an A 10-TX transmitter.| Channel| •+14 dBu
•+2 dBu
•-10 dBu
•-22 dBu
Audio Polarity| | Selects the polarity of the balanced output signal.| Channel| •Normal
•Inverted
Mode| | Chooses the audio output type of the A 10-RX. When the AIO-RX is set to AES the channel 2 XLR connection is not used.| Global| •Analogue
•AES
Test Tone| | Activates an I kHz tone oscillator sent directly to the outputs. tone
This disrupts the output from a linked A10-TX transmitter| Channel| •-18 dBFS

Settings Sub-Menu
All setting is Global.

The Modulation setting must match between the A20-Mini or A10-TX and the A10-RX in order for the transmitted signal to be received.| •Std (Standard)
•LR (Long Range)
User Groups| | Sets whether the receiver utilizes user groups (User) or manual frequency selection (Factory).| •User
•Factory
TV Ch Map| | Selects the TV channel spacing in MHz to ensure channel selection corresponds to a specific geographic region. See frequency chart.| •X — 6 MHz
•Y – 7 MHz
•Z – 8 MHz
Display| | Enters Display sub-menu.| •Brightness
•Screensaver
•Orientation
•Options
•Q-meter
LEDs| | When set to On the LEDs remain illuminated. Off deactivates the LEDs.| •On
•Off

Display Sub-Menu
All settings are Global.

1-5,5 is the brightest
Screensaver| | Sets the duration, in seconds, of how long the screen remains on after a button press. Off keeps the screen on continuously with no screensaver.| •Off – the display remains on when the unit is powered
•5 sec
•30 sec
•120 sec
Orientation| | Sets the operating orientation of the menu screen and LEDs. The Al O-RX can be used in an orientation with the buttons below the screen (normal), or with the buttons to the top (flipped).| •Normal
•Flipped
Options| | Sets whether Frequency or TV Channel is displayed on the dual channel screen.| •Frequency
•TV Ch
Q-meter| | Sets the Q-meter display size. The audio meter is displayed larger when Q-meter is small.| •Large
•Small

System Sub-Menu
All settings are Global.

•1 and 2 – both channels 1 and 2
•2 – channel 2 only
• Off-receiver circuits off
Restore| | The restore function allows the user to reset the A10-RX to the factory default settings.
Restore sets the TV Channel Map to region Z. Select the current region in your locality before proceeding.|
Info| | Shows numerous attributes of the transmitter.| •Serial Number
•Firmware Revision
•Frequency Band

Basic Operation

Frequency Selection
The A10 Digital Wireless System operates in the UHF frequency band from 470 to 694 MHz The A10-RX can tune across the entire range of the system.
Because the A10 digital RF transmission is inherently immune to intermodulation multiple A10 Digital Wireless systems can be used simultaneously on nearby adjacent frequencies without the worry of intermodulation interference Systems can be used together when separated by at least 400 kHz
Setting Channel, Sub Channel, Frequency
To simplify frequency selection, frequencies are divided into channels and sub-channels The specific frequencies corresponding to channels and sub- channels depend on the setting of the TV Channel Mapping (Main > Settings > TV Ch Map) Three options are available, 6, 7, and 8 MHz spacing, X, Y, and Z respectively These three settings generally correspond to three main geographic regions, the Americas, Australia/New Zealand, and Europe, respectively For more information, see Frequency Tables

• Channel – corresponds to broadcast television channels used in a geographic region Depending on the selected channel mapping, channels cover 6, 7, or 8 MHz
• Sub Channel – channels are divided into 400 kHz increments called sub-channels to speed up frequency selection The number of sub-channels depends on the channel mapping selected
• Frequency-specific frequencies within the receiver tuning range can be selected in 25 kHz increments When a selected frequency does not correspond with a  channel/sub-channel mapping, an asterisk character (*) is shown in the display adjacent to the channel/sub-channel assignment below the frequency shown

To change TV channels:

1. Use the Left button to highlight the TV Channel
2. Press the Centre Menu to select the TV channel
3. Select the subchannel until the desired sub-channel is selected
   Remember, for a given channel/sub-channel, the actual frequency will change depending on the TV Channel Mapping setting.

See the Frequency Tables in this guide for a complete list of frequencies corresponding to the channel and sub-channel selections

Modulation

Modulation can be set to Standard (Std) or Long Range (LR) in Menu > Settings

Modulation.
When compared to Standard Modulation, Long Range Modulation has better sensitivity This increased sensitivity results in a more robust performance in challenging RF environments
The Modulation setting must match between the A20-Mini or A10-TX and the A10-RX in order for the transmitted signal to be received.
Frequency Scanning
The frequency scanning tool uses the radios in the A10-RX to measure and display RF activity within the system’s tuning range. This allows a user to find frequencies with low RF activity suitable for system operation The scan tool operates over the full 224 MHz bandwidth of the receiver Enter the scanner from the Selection Menu Main > Scan
Audio from channel 1 and channel 2 is muted when the scan tool is active.
To initiate a scan, press the >> button The scan will start, working from lower frequencies to higher frequencies, The cursor can be seen to move along the screen denoting the current position of the scan can be stopped by pressing the Left button Selecting the > button allows the user to manually step through in 400 kHz steps at a time Selecting the << button allows the user to automatically scan backward, and similarly selecting the < button allows the user to manually step lower in frequency in 400 kHz steps
Partial Scanning, 25 MHz Increments
In partial scanning mode, the receiver scans a 25 MHz range This partial scan improves the resolution of the scan over a full scan The ten partial scans cover the following ranges:

Full Scan, 224 MHz
The full receiver bandwidth of 224 MHz can also be scanned
User Group Scan
When user groups are in use, an additional option called UG is available in the Scan menu Selecting this will only scan frequencies in the loaded user group
Audio Output and Control
The A10-RX outputs either analog line level or AES3 digital audio This global setting applies to both channel outputs
Analog Output
When set to analog in the Selection Menu the A10-RX outputs low-impedance, balanced line-level audio It is designed to connect to balanced or unbalanced line-level inputs To unbalance the output, float pin-3.
AES Digital Output
When set to AES output in the Selection Menu the A10-RX outputs two-channel AES3 at 24bit, 44.1 kHz Channel 1 output appears at AES left, channel 2 appears at AES right
With the A10-RX-XLR the channel 1 XLR connector is used for AES3 output channel 2 The XLR connector is not active when set to AES output
Antennae
The SMA antenna connector is used to mount the included 1/4-wave whip antenna For specialty applications external, high-gain receiving antennae can be attached to the SMA connector
Ensure that the antennae used are built for the correct frequency.
For best operation and reception power with the included 1/4-wave antenna, keep it in the free field, away from metal objects or transmitting devices.

User Groups

The User Groups feature allows for easy, intuitive naming of specific frequencies for each A10 the transmitter used on set and grouped together for faster tuning The operator of an A10 receiver may then easily switch between transmitters by choosing alphanumeric names, such as “Jack” and “Jill”, instead of having to remember and manually tune to different, specific numerical frequencies.
For instance, a producer or director may want to monitor several different actors’ wireless transmitters Rather than having to keep a list of all of their frequencies, each transmitter may be pre-assigned a frequency and given an actor’s name Then only those pre-assigned frequencies that have been named will be available as possible options for tuning User Group files are created using SD-Utility—a Windows and Mac application available for free download from the Sound Devices website
https://www.sounddevices.com/download/?prod=sd-utility
Once created, the User Group files are uploaded to A10 transmitters and receivers.
A20-Mini does not support User Groups.
To create a new user group:

1. Open SD-Utility on your computer

2. Do one of the following:
   • On a Mac, select User Group File > New
   • On a PC, select File > User Groups > Create a new file.

3. Name the new group

4. Select a range of frequencies via the Band drop-down list Options include A, B, C, and D and This will automatically restrict users in the group to the frequencies within that band Selecting Any will make frequencies within all bands available for assignment to users in the group
   All A10-TX will have the available bands listed on the printed label inside the battery compartment door as well as display the frequencies capable of being generated by the transmitter in Menu > System > Info.

5. Select OK. The User Group Editor screen appears with fields for the first user (U1) available.

6. Enter a Name and Frequency for U1 in the fields provided. The A10-TX transmitter’s serial number is optional.
   Entry of ineligible frequencies (or characters) will cause the text in the field to appear red.
   SD-Utility automatically fills in .000 as the subchannel variable for frequencies entered as a whole number SD-Utility automatically follows the best-practice method of spacing adjacent transmitters by at least one subchannel, preventing possible interference from other transmitters

7. Click Add (on a PC) —or the Plus (+) button on a Mac— to add the user to the group. This also adds a new line for the next user (U2, U3, etc) Each user in a group can be given a name and frequency, which after upload, will then be displayed on A10 receivers and transmitters Each group can have up to 32 users

SD-Utility supports the creation of up to eight user groups, each with a max of 32 users, per Audio Limited User Group (ALUG) file.
To add additional user groups:

1. In SD-Utility, select Add Group
2. Name the new group and select the band of frequencies for the group
3. Add users (defining name and frequencies) to the group.

Audio Limited User Group files (ALUG) may be saved for future use and modification. When saving the ALUG file, SD-Utility will default the file name to the first User Group name in the drop-down list
To load an ALUG file into SD-Utility:

1. In SD-Utility, select User Group File > Open
2. Choose an ALUG file on your computer.

To remove a user group:

1. In SD-Utility, select a User Group in the drop-down list
2. Select Remove Group

Sending and Loading User Groups onto A10 Receivers
While each ALUG file may contain up to eight user groups, only one group at a time may be sent to and loaded on an A10 receiver A user group is sent to the A10-RX-XLR directly connecting it to a computer via USB Sending a user group to the A10-RX-SL is achieved via the A10-RACK or the Sound Devices 688 or 8-Series Mixer-Recorders with attached SL-2 or SL-6
For instructions on sending user groups to A10 transmitters, see the A10-TX User Guide or the A10-TX-US User Guide.
To send a user group to an A10-RX via A-XLR, A-RXMON, or A-15PIN::

1. Start the SD-Utility application

2. Connect the A10-RX via USB to the computer
   The A-XLR and A-RXMON connect via microUSB
   The A-15PIN connects via USB-C
   Note: A USB 3 0 port is required to power the A10-RX via the A-15PIN If a USB 3 0 port is not available, connect two USB 2 0 ports to the A-15PIN using the Sound Devices MX-USB Y USB-C to two USB-A Y-Cable. The A10-RX must be running firmware v3.00 or higher, in order to connect to SD-Utility

3. Load the ALUG file into SD-Utility.

4. Select Send to RX SD-Utility detects and displays the connected receiver

5. Select the Send check box and click Send

To send a user group to A10-RX-SL receivers via A10-RACK:

1. Start the SD-Utility application
2. Connect the A10-RACK to the computer’s USB port
3. Load the ALUG file into SD-Utility.
4. Select Send to RX SD-Utility will detect and display all A10-RX receivers installed in the A10-RACK
5. Select the check boxes next to each receiver to which you want to send the User Group
6. Click Send

To send a user group to A10-RX-SL receivers via 688/SL-6:

1. Using an SD card already formatted in a 688, save the ALUG file to a formatted SD card.

2. Insert the SD card into the 688

3. With the A10-RX-SL receiver(s) in the SL-6 slots, power on the 688/SL-6

4. Access the Receiver Overview screen by doing either of the following:
   • HP + METERS: Press and hold the Headphone encoder, then press the METERS button
   • Press MENU, then use the Headphone encoder to select SL-6 > Receiver Overview

5. Select a channel

6. Slide RTN/FAV switch right to select Menu

7. Select User Groups > User > Load New

8. Select a user group from the ALUG file.

To send a user group to A10-RX-SL receivers via Scorpio with SL-6 or 8-Series with SL-2:

1. Using an SD card already formatted in an 8-Series Mixer-Recorder, save the ALUG file to a formatted SD card

2. Insert the SD card into the 8-Series Mixer-Recorder

3. With the A10-RX-SL receiver(s) in the SL-2 or SL-6 slots, power on the 8-Series MixerRecorder

4. Access the Receiver Overview screen by doing either of the following:
   • METERS + HP: Press and hold the METERS button, then press the Headphone encoder
   • Press MENU, then use the Select encoder to select SuperSlot>SL-2/SL-6 Receiver Overview

5. Select a channel

6. Slide RTN/FAV switch right to select Options

7. Select User Groups > User > Load New

8. Select a user group from the ALUG file.

Loading User Groups on A10-RX
While the SD card can have multiple ALUG files, each with up to eight groups, only one user group at a time may be loaded to a receiver
A10-RX receivers can operate in one of two modes: User and Factory In Factory mode, frequencies are manually dialed in, but in User mode (when a user group is loaded), pre-set frequencies are dialed in by user name
To set the receiver to User mode:

1. Press the Centre Menu button on the receiver
2. Select Settings > User Groups > User

To dial in a specific User Group frequency:

1. Press the Centre Menu button on the receiver
2. Select Frequency
3. Press the Left or Right button to select one of the user names The frequency will appear along with the name
   While in User mode, no non-user group frequencies will be selectable. To revert back to manual frequency selection, set the mode to Factory (Menu > Settings > User Groups > Factory.)

Firmware Updates

Periodically Audio Ltd. issues new firmware for the A10-RX receiver. Make certain to register your product at the Sound Devices website to receive firmware update notifications. Firmware is installed on the A10-RX via SD- Utility or via select Sound Devices Mixer-Recorders Download the latest firmware PRG from the Sound Devices website at: https://www.sounddevices.com/download/
A Change List of new features for the latest firmware can also be found on this webpage.
SD-Utility
The Sound Devices SD-Utility software utility includes a receiver firmware update tool.
SD-Utility is available as a free download for macOS 10 11+ or Windows 10+ computers.
Download the latest version of SD-Utility from the Sound Devices website at: https://www.sounddevices.com/download/?prod=sd-utility
macOS users will also need to download and install the CP210x USB to UART Bridge VCP Drivers from the Silicon Labs website at:
https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers
A10-RX connects to SD-Utility via the A-XLR, A-RXMON, A-15PIN, or A10-RACK
To update A10-RX firmware via A-XLR, A-RXMON, or A-15PIN:

1. Download the new firmware PRG file from the Sound Devices website.

2. Launch the SD-Utility application

3. Connect the A10-RX via USB to the computer
   The A-XLR and A-RXMON connect via microUSB
   The A-15PIN connects via USB-C
   Note: A USB 3 0 port is required to power the A10-RX via the A-15PIN If a USB 3 0 port is not available, connect two USB 2 0 ports to the A-15PIN using the Sound Devices MX-USB Y USB-C to two USB-A Y-Cable. The A10-RX must be running firmware v3.00 or higher, in order to connect to SD-Utility

4. Connect a power source to the A-RXMON or A-XLR The A-15PIN does not require additional power

5. Power on the A10-RX

6. From SD-Utility, select File > Update RX and then select the firmware PRG file to install.

7. Follow the on-screen prompts

To update A10-RX firmware via A10-RACK:

1. Download the new firmware PRG file from the Sound Devices website.

2. Launch the SD-Utility application

3. Connect the A10-RACK back panel USB-B port to the computer’s USB-A port using a standard USB-A to -B cable

4. Ensure all A10-RX receivers are properly slotted into the A10-RACK Power on the A10RACK and A10-RX-SL receivers

5. From SD-Utility, select File > Update RX and then select the firmware PRG file to install. After a momentary refresh, SD-Utility will detect all A10-RX-SL receivers in the A10 RACK SD-Utility will display the A10 Receivers listed in order and display the Serial Number and current Firmware Version
   

6. SD-Utility detects A10 Receivers running older versions of Firmware and automatically selects them to be updated Otherwise, select the Update check box for each RX you want to update, and then click Update

7. Click OK to confirm, if prompted. A status bar will indicate the progress of each A10 Receiver update
   Receivers are updated one at a time. As the receiver is updated, its screen will display Programming and the LEDs will turn off. This is a normal operation. After the update, the receiver’s menu will be available again.
   An Update Complete popup appears after all receivers have been updated

8. Click OK when Firmware Update is complete

Updating A10-RX from Sound Devices Mixer-Recorders
Updating the firmware on the A10-RX-SL may be done via the Sound Devices 688 or 8-Series Mixer-Recorders, while the receiver is slotted into the SL-2 or SL-6
To update firmware on an A10-RX-SL via the 688 and SL-6:

1. Download the new firmware PRG file from the Sound Devices website and copy it to an SD card.

2. Power on the 688 and SL-6

3. Insert the SD card into the slot on the side of the 688

4. METERS + HP: Press the METERS button, then push in the Headphone encoder to access the Receiver Overview screen

5. Turn and press the Headphone encoder to select a receiver This accesses the Receiver Details screen
   You need only select either channel per receiver to perform the update for the entire receiver.

6. Slide RTN/FAV switch to select Menu

7. Use the Headphone encoder to select Update Firmware. The 688 will prompt you to confirm a search of inserted CF/SD cards for a programming file (PRG). Select OK to continue.

8. After it finds a file, the 688 will prompt you to confirm it has found the correct file. If it is, select OK to continue
   As the receiver is updated, its screen will display Programming and the LEDs will turn off.
   This is a normal operation.

9. Repeat steps for each receiver in the SL-6

To update A10-RX-SL firmware via the Scorpio and SL-6 or the 8-Series and SL-2:

1. Download the new firmware PRG file from the Sound Devices website and copy it to an SD card.

2. Power on the 8-Series

3. Insert the SD card into the slot on the side of the 8-Series

4. METERS + HP: Press the METERS button, then push in the Headphone encoder to access the Receiver Overview screen

5. Turn and press the Select encoder to select a receiver This accesses the Receiver Details screen
   You need only select either channel per receiver to perform the update for the entire receiver

6. Slide RTN/FAV switch to select Options

7. Use either encoder to select Update Firmware. After it finds a file, the 8-Series prompts you to confirm it has found the correct file. If it is, select OK to continue.
   As the receiver is updated, its screen will display Programming and the LEDs will turn off.
   This is a normal operation.

8. Repeat steps for each receiver in the SL-2 or SL-6

Converting Between XLR and SL Mounts

The A10-RX receiver is modular in design. With the correct accessories—either the A-SL or the A-XLR adapters—the A10-RX-SL slot receiver and A10-RX-XLR cabled receiver can be converted between each type

• The A-SL accessory is a 25-Pin D-Type Uni/Superslot adapter and comes with the A-PLATE spacer
• The A-XLR accessory is an XLR and power cable adapter

To convert from an A10-RX-SL to an A10-RX-XLR:

1. Remove the four perimeter screws Do not remove the two screws on either side of the 25pin D-Type connector
   

2. Remove the A-SL accessory
   

3. Position the A-XLR accordingly, and replace the screws
   Complete the above procedure in reverse to convert from A10-RX-XLR to A10-RX- SL.

A-15PIN Accessory

A10-RX supports the Sound Devices A-15PIN adapter for Sony’s proprietary wireless slot The A-15PIN connects an A10-RX directly to Sony camcorders/extension units and sends two channels of AES digital wireless audio When connected to the camcorder via the A-15PIN, the A10-RX receives power and powers up and down with the camcorder Installation instructions for the A-15PIN and a list of supported Sony cameras can be found here:
https://www.sounddevices.com/a-15pin-installation/

A-RXMON Accessory

Monitor any A10 transmitter on set with this handy belt-worn headphone amp for your A10-RX The A-RXMON provides a simple, portable solution for easily monitoring two A10-TX audio channels with headphones
See the A-RXMON User Guide for more details

Specifications

Frequency Range| World Models: A10-RX-SL (470–694 MHz) A10-RX-SL-US (470–608 MHz)
U.S. Only Models: A10-RX-XLR (470–694 MHz) A10-RX-XLR-US (470–608 MHz)
Transmitters are tunable in 25 kHz steps.
---|---
Modulation Mode| Proprietary digital RF modulation Standard or Long Range, selectable
Latency| Standard modulation = 2 ms, Long Range modulation 3.9 ms, measured at analog output.
Digital Audio Codec| Audio Ltd.’s proprietary, the high- performance digital encoding algorithm
Audio Frequency Response| 20 Hz–20 kHz
Maximum Output Level| +14 dBu, +2 dBu, -10 dBu, or -22 dBu, menu- selectable, with a 0 dBFS signal at the transmitter input, 130 ohms impedance
Digital Audio Output| AES3 balanced connection, 110 ohms, left=channel 1, right=channel 2
Menu and Controls| OLED menu display, 3 button navigation
Privacy| User settable 4-digit PIN, Audio Ltd. proprietary
Powering| 6–18 VDC, approx. 3 W with one receiver active, approx. 4.4 W with two receivers active
Operating Temperature Range| -10 °C to +55 °C
Weight and Dimensions| 207 g, 124 x 68 x 18 mm

A10-RX-SL DB-25 Connector Pin Assignments
The illustration below shows the pin assignments of the A10-RX-SL when viewing the bottom connector

DB-25
Pin

| Name|

Description

---|---|---
1| Ground| Ground connection
2| Ch 1+ analogue / Ch 1,2 AES +| Ch 1 + analogue audio out, +2 dBu level (+/- 0.5 dB), balanced. Alternately, Ch1 and Ch 2 AES3+ (balanced, 110 ohm, transformerless).
3| Ch 1 – analogue / Ch 1,2 AES –| Ch 1 – analogue audio out, +2 dBu level (+/- 0.5 dB), balanced. Alternately, Ch 1 and Ch 2 AES3- (balanced, 110 ohms, transformerless).
4| Ground| Ground for power
5| 6-18 VDC| Power supply, 6.0-18.0 V, 6 W max.
6| no connection
7| no connection
8| no connection
9| no connection
10| no connection
11| no connection
12| no connection
13| Ground| Ground connection
14| Ground| Ground connection
15| Ch 2+ analogue| Ch 2 + analogue audio out, +2 dBu level (+/- 0.5 dB), balanced.
16| Ch 2- analogue| Ch 2 – analogue audio out, +2 dBu level (+/- 0.5 dB), balanced.
17| no connection
18| no connection
19| no connection
20| no connection
21| no connection
22| UART transmit (0/3.3V)| UART from A10-RX. 0/3.3V signaling.
23| UART receive (0/3.3V)| UART to A10-RX. 0/3.3 V signaling.
24| no connection
25| Ground| Ground connection

Certifications

Industry Canada Conformity
This radio transmitter has been approved by Industry Canada to operate with the supplied monopole whip antenna only Other antenna types are strictly prohibited for use with this device This device operates on a no-protection no-interference basis Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio license is required Please consult Industry Canada’s document CPC-2-1-28, ‘Optional Licencing for Low-Power Radio Apparatus in the TV Bands’, for details.
This device complies with Industry Canada’s license exempt RSSs Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device
FCC Conformity
The A10-RX receiver complies with the following requirements:
FCC (Federal Communications Commission) Part 15
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation

Declaration of Conformity
The Declaration of Conformity documentation is provided online at: https://www.sounddevices.com/audio-ltd-doc/

Warranty

Audio Ltd warrants the items listed above against defects in materials and workmanship for a period of two (2) years from the date of original retail purchase Products must be purchased through authorized Audio Ltd resellers to qualify for Warranty coverage Damage resulting from the opening of an Audio Ltd product or attempted repairs by non-authorized personnel will void warranty coverage.
This is a non-transferable warranty that extends only to the original purchaser Audio Ltd will repair or replace the product at its discretion at no charge Warranty claims due to severe service conditions will be addressed on an individual basis.
This warranty does not apply to defects caused by misuse, abuse or altered goods There are no express or implied warranties that extend beyond the warranty made here All warranty submissions must include an unaltered copy of the original sales receipt from an authorized Audio Ltd reseller.
For additional information about warranty-related claims, contact support.

Frequency Tables

The A10-TX offers preselected frequencies based on channels and sub-channels Three sets of frequencies are available based on either 6, 7, or 8 MHz channel bandwidth Select the channel bandwidth based on the geographic region where the unit is operating
X Frequencies (6 MHz Per TV Channel)
The chart below shows all frequencies available for the A10 wireless system Not all channels are available on all transmitters.

|

Sub Channel

---|---
1| 2| 3| 4| 5| 6| 7| 8| 9| 10| 11| 12| 13| 14| 15
Channel| 14| 470.2| 470.6| 471| 471.4| 471.8| 472.2| 472.6| 473| 473.4| 473.8| 474.2| 474.6| 475| 475.4| 475.8
15| 476.2| 476.6| 477| 477.4| 477.8| 478.2| 478.6| 479| 479.4| 479.8| 480.2| 480.6| 481| 481.4| 481.8
16| 482.2| 482.6| 483| 483.4| 483.8| 484.2| 484.6| 485| 485.4| 485.8| 486.2| 486.6| 487| 487.4| 487.8
17| 488.2| 488.6| 489| 489.4| 489.8| 490.2| 490.6| 491| 491.4| 491.8| 492.2| 492.6| 493| 493.4| 493.8
18| 494.2| 494.6| 495| 495.4| 495.8| 496.2| 496.6| 497| 497.4| 497.8| 498.2| 498.6| 499| 499.4| 499.8
19| 500.2| 500.6| 501| 501.4| 501.8| 502.2| 502.6| 503| 503.4| 503.8| 504.2| 504.6| 505| 505.4| 505.8
20| 506.2| 506.6| 507| 507.4| 507.8| 508.2| 508.6| 509| 509.4| 509.8| 510.2| 510.6| 511| 511.4| 511.8
21| 512.2| 512.6| 513| 513.4| 513.8| 514.2| 514.6| 515| 515.4| 515.8| 516.2| 516.6| 517| 517.4| 517.8
22| 518.2| 518.6| 519| 519.4| 519.8| 520.2| 520.6| 521| 521.4| 521.8| 522.2| 522.6| 523| 523.4| 523.8
23| 524.2| 524.6| 525| 525.4| 525.8| 526.2| 526.6| 527| 527.4| 527.8| 528.2| 528.6| 529| 529.4| 529.8
24| 530.2| 530.6| 531| 531.4| 531.8| 532.2| 532.6| 533| 533.4| 533.8| 534.2| 534.6| 535| 535.4| 535.8
25| 536.2| 536.6| 537| 537.4| 537.8| 538.2| 538.6| 539| 539.4| 539.8| 540.2| 540.6| 541| 541.4| 541.8
26| 542.2| 542.6| 543| 543.4| 543.8| 544.2| 544.6| 545| 545.4| 545.8| 546.2| 546.6| 547| 547.4| 547.8
27| 548.2| 548.6| 549| 549.4| 549.8| 550.2| 550.6| 551| 551.4| 551.8| 552.2| 552.6| 553| 553.4| 553.8
28| 554.2| 554.6| 555| 555.4| 555.8| 556.2| 556.6| 557| 557.4| 557.8| 558.2| 558.6| 559| 559.4| 559.8
29| 560.2| 560.6| 561| 561.4| 561.8| 562.2| 562.6| 563| 563.4| 563.8| 564.2| 564.6| 565| 565.4| 565.8
30| 566.2| 566.6| 567| 567.4| 567.8| 568.2| 568.6| 569| 569.4| 569.8| 570.2| 570.6| 571| 571.4| 571.8
31| 572.2| 572.6| 573| 573.4| 573.8| 574.2| 574.6| 575| 575.4| 575.8| 576.2| 576.6| 577| 577.4| 577.8
32| 578.2| 578.6| 579| 579.4| 579.8| 580.2| 580.6| 581| 581.4| 581.8| 582.2| 582.6| 583| 583.4| 583.8
33| 584.2| 584.6| 585| 585.4| 585.8| 586.2| 586.6| 587| 587.4| 587.8| 588.2| 588.6| 589| 589.4| 589.8
34| 590.2| 590.6| 591| 591.4| 591.8| 592.2| 592.6| 593| 593.4| 593.8| 594.2| 594.6| 595| 595.4| 595.8
35| 596.2| 596.6| 597| 597.4| 597.8| 598.2| 598.6| 599| 599.4| 599.8| 600.2| 600.6| 601| 601.4| 601.8
36| 602.2| 602.6| 603| 603.4| 603.8| 604.2| 604.6| 605| 605.4| 605.8| 606.2| 606.6| 607| 607.4| 607.8
37| 608.2| 608.6| 609| 609.4| 609.8| 610.2| 610.6| 611| 611.4| 611.8| 612.2| 612.6| 613| 613.4| 613.8
38| 614.2| 614.6| 615| 615.4| 615.8| 616.2| 616.6| 617| 617.4| 617.8| 618.2| 618.6| 619| 619.4| 619.8
39| 620.2| 620.6| 621| 621.4| 621.8| 622.2| 622.6| 623| 623.4| 623.8| 624.2| 624.6| 625| 625.4| 625.8
40| 626.2| 626.6| 627| 627.4| 627.8| 628.2| 628.6| 629| 629.4| 629.8| 630.2| 630.6| 631| 631.4| 631.8
41| 632.2| 632.6| 633| 633.4| 633.8| 634.2| 634.6| 635| 635.4| 635.8| 636.2| 636.6| 637| 637.4| 637.8
42| 638.2| 638.6| 639| 639.4| 639.8| 640.2| 640.6| 641| 641.4| 641.8| 642.2| 642.6| 643| 643.4| 643.8
43| 644.2| 644.6| 645| 645.4| 645.8| 646.2| 646.6| 647| 647.4| 647.8| 648.2| 648.6| 649| 649.4| 649.8
44| 650.2| 650.6| 651| 651.4| 651.8| 652.2| 652.6| 653| 653.4| 653.8| 654.2| 654.6| 655| 655.4| 655.8
45| 656.2| 656.6| 657| 657.4| 657.8| 658.2| 658.6| 659| 659.4| 659.8| 660.2| 660.6| 661| 661.4| 661.8
46| 662.2| 662.6| 663| 663.4| 663.8| 664.2| 664.6| 665| 665.4| 665.8| 666.2| 666.6| 667| 667.4| 667.8
47| 668.2| 668.6| 669| 669.4| 669.8| 670.2| 670.6| 671| 671.4| 671.8| 672.2| 672.6| 673| 673.4| 673.8
48| 674.2| 674.6| 675| 675.4| 675.8| 676.2| 676.6| 677| 677.4| 677.8| 678.2| 678.6| 679| 679.4| 679.8
49| 680.2| 680.6| 681| 681.4| 681.8| 682.2| 682.6| 683| 683.4| 683.8| 684.2| 684.6| 685| 685.4| 685.8
50| 686.2| 686.6| 687| 687.4| 687.8| 688.2| 688.6| 689| 689.4| 689.8| 690.2| 690.6| 691| 691.4| 691.8
51| 692.2| 692.6| 693| 693.4| 693.8| 694.2| 694.6| 695| 695.4| 695.8| 696.2| 696.6| 697| 697.4| 697.8

Y Frequencies (7 MHz Per TV Channel)

|

Sub Channels

---|---
1| 2| 3| 4| 5| 6| 7| 8| 9| 10| 11| 12| 13| 14| 15| 16| 17
Channels| 22| 485.3| 485.7| 486.1| 486.5| 486.9| 487.3| 487.7| 488.1| 488.5| 488.9| 489.3| 489.7| 490.1| 490.5| 490.9| 491.3| 491.7
23| 492.3| 492.7| 493.1| 493.5| 493.9| 494.3| 494.7| 495.1| 495.5| 495.9| 496.3| 496.7| 497.1| 497.5| 497.9| 498.3| 498.7
24| 499.3| 499.7| 500.1| 500.5| 500.9| 501.3| 501.7| 502.1| 502.5| 502.9| 503.3| 503.7| 504.1| 504.5| 504.9| 505.3| 505.7
25| 506.3| 506.7| 507.1| 507.5| 507.9| 508.3| 508.7| 509.1| 509.5| 509.9| 510.3| 510.7| 511.1| 511.5| 511.9| 512.3| 512.7
26| 513.3| 513.7| 514.1| 514.5| 514.9| 515.3| 515.7| 516.1| 516.5| 516.9| 517.3| 517.7| 518.1| 518.5| 518.9| 519.3| 519.7
27| 520.3| 520.7| 521.1| 521.5| 521.9| 522.3| 522.7| 523.1| 523.5| 523.9| 524.3| 524.7| 525.1| 525.5| 525.9| 526.3| 526.7
28| 527.3| 527.7| 528.1| 528.5| 528.9| 529.3| 529.7| 530.1| 530.5| 530.9| 531.3| 531.7| 532.1| 532.5| 532.9| 533.3| 533.7
29| 534.3| 534.7| 535.1| 535.5| 535.9| 536.3| 536.7| 537.1| 537.5| 537.9| 538.3| 538.7| 539.1| 539.5| 539.9| 540.3| 540.7
30| 541.3| 541.7| 542.1| 542.5| 542.9| 543.3| 543.7| 544.1| 544.5| 544.9| 545.3| 545.7| 546.1| 546.5| 546.9| 547.3| 547.7
31| 548.3| 548.7| 549.1| 549.5| 549.9| 550.3| 550.7| 551.1| 551.5| 551.9| 552.3| 552.7| 553.1| 553.5| 553.9| 554.3| 554.7
32| 555.3| 555.7| 556.1| 556.5| 556.9| 557.3| 557.7| 558.1| 558.5| 558.9| 559.3| 559.7| 560.1| 560.5| 560.9| 561.3| 561.7
33| 562.3| 562.7| 563.1| 563.5| 563.9| 564.3| 564.7| 565.1| 565.5| 565.9| 566.3| 566.7| 567.1| 567.5| 567.9| 568.3| 568.7
34| 569.3| 569.7| 570.1| 570.5| 570.9| 571.3| 572.7| 573.1| 573.5| 573.9| 574.3| 574.7| 575.1| 575.5| 575.9| 576.3| 576.7
35| 576.3| 576.7| 577.1| 577.5| 577.9| 578.3| 578.7| 579.1| 579.5| 579.9| 580.3| 580.7| 581.1| 581.5| 581.9| 582.3| 582.7
36| 583.3| 583.7| 584.1| 584.5| 584.9| 585.3| 585.7| 586.1| 586.5| 586.9| 587.3| 587.7| 588.1| 588.5| 588.9| 589.3| 589.7
37| 590.3| 590.7| 591.1| 591.5| 591.9| 592.3| 592.7| 593.1| 593.5| 593.9| 594.3| 594.7| 595.1| 595.5| 595.9| 596.3| 596.7
38| 597.3| 597.7| 598.1| 598.5| 598.9| 599.3| 599.7| 600.1| 600.5| 600.9| 601.3| 601.7| 602.1| 602.5| 602.9| 603.3| 603.7
39| 604.3| 604.7| 605.1| 605.5| 605.9| 606.3| 606.7| 607.1| 607.5| 607.9| 608.3| 608.7| 609.1| 609.5| 609.9| 610.3| 610.7
40| 611.3| 611.7| 612.1| 612.5| 612.9| 613.3| 613.7| 614.1| 614.5| 614.9| 615.3| 615.7| 616.1| 616.5| 616.9| 617.3| 617.7
41| 618.3| 618.7| 619.1| 619.5| 619.9| 620.3| 620.7| 621.1| 621.5| 621.9| 622.3| 622.7| 623.1| 623.5| 623.9| 624.3| 624.7
42| 625.3| 625.7| 626.1| 626.5| 626.9| 627.3| 627.7| 628.1| 628.5| 628.9| 629.3| 629.7| 630.1| 630.5| 630.9| 631.3| 631.7
43| 632.3| 632.7| 633.1| 633.5| 633.9| 634.3| 634.7| 635.1| 635.5| 635.9| 636.3| 636.7| 637.1| 637.5| 637.9| 638.3| 638.7
44| 639.3| 639.7| 640.1| 640.5| 640.9| 641.3| 641.7| 642.1| 642.5| 642.9| 643.3| 643.7| 644.1| 644.5| 644.9| 645.3| 645.7
45| 646.3| 646.7| 647.1| 647.5| 647.9| 648.3| 648.7| 649.1| 649.5| 649.9| 650.3| 650.7| 651.1| 651.5| 651.9| 652.3| 652.7
46| 653.3| 653.7| 654.1| 654.5| 654.9| 655.3| 655.7| 656.1| 656.5| 656.9| 657.3| 657.7| 658.1| 658.5| 658.9| 659.3| 659.7
47| 660.3| 660.7| 661.1| 661.5| 661.9| 662.3| 662.7| 663.1| 663.5| 663.9| 664.3| 664.7| 665.1| 665.5| 665.9| 666.3| 666.7
48| 667.3| 667.7| 668.1| 668.5| 668.9| 669.3| 669.7| 670.1| 670.5| 670.9| 671.3| 671.7| 672.1| 672.5| 672.9| 673.3| 673.7
49| 674.3| 674.7| 675.1| 675.5| 675.9| 676.3| 676.7| 678.1| 678.5| 678.9| 679.3| 679.7| 680.1| 680.5| 680.9| 681.3| 681.7
50| 681.3| 681.7| 682.1| 682.5| 682.9| 683.3| 683.7| 684.1| 684.5| 684.9| 685.3| 685.7| 686.1| 686.5| 686.9| 687.3| 687.7
51| 688.3| 688.7| 689.1| 689.5| 689.9| 690.3| 690.7| 691.1| 691.5| 691.9| 692.3| 692.7| 693.1| 693.5| 693.9| 694.3| 694.7

Z Frequencies (8 MHz Per TV Channel)

| Sub Channels
---|---
1| 2| 3| 4| 5| 6| 7| 8| 9| 10| 11| 12| 13| 14| 15| 16| 17| 18| 19| 20
Channels| 21| 470.2| 470.6| 471.0| 471.4| 471.8| 472.2| 472.6| 473.0| 473.4| 473.8| 474.2| 474.6| 475.0| 475.4| 475.8| 476.2| 476.6| 477.0| 477.4| 477.8
22| 478.2| 478.6| 479.0| 479.4| 479.8| 480.2| 480.6| 481.0| 481.4| 481.8| 482.2| 482.6| 483.0| 483.4| 483.8| 484.2| 484.6| 485.0| 485.4| 485.8
23| 486.2| 486.6| 487.0| 487.4| 487.8| 488.2| 488.6| 489.0| 489.4| 489.8| 490.2| 490.6| 491.0| 491.4| 491.8| 492.2| 492.6| 493.0| 493.4| 493.8
24| 494.2| 494.6| 495.0| 495.4| 495.8| 496.2| 496.6| 497.0| 497.4| 497.8| 498.2| 498.6| 499.0| 499.4| 499.8| 500.2| 500.6| 501.0| 501.4| 501.8
25| 502.2| 502.6| 503.0| 503.4| 503.8| 504.2| 504.6| 505.0| 505.4| 505.8| 506.2| 506.6| 507.0| 507.4| 507.8| 508.2| 508.6| 509.0| 509.4| 509.8
26| 510.2| 510.6| 511.0| 511.4| 511.8| 512.2| 512.6| 513.0| 513.4| 513.8| 514.2| 514.6| 515.0| 515.4| 515.8| 516.2| 516.6| 517.0| 517.4| 517.8
27| 518.2| 518.6| 519.0| 519.4| 519.8| 520.2| 520.6| 521.0| 521.4| 521.8| 522.2| 522.6| 523.0| 523.4| 523.8| 524.2| 524.6| 525.0| 525.4| 525.8
28| 526.2| 526.6| 527.0| 527.4| 527.8| 528.2| 528.6| 529.0| 529.4| 529.8| 530.2| 530.6| 531.0| 531.4| 531.8| 532.2| 532.6| 533.0| 533.4| 533.8
29| 534.2| 534.6| 535.0| 535.4| 535.8| 536.2| 536.6| 537.0| 537.4| 537.8| 538.2| 538.6| 539.0| 539.4| 539.8| 540.2| 540.6| 541.0| 541.4| 541.8
30| 542.2| 542.6| 543.0| 543.4| 543.8| 544.2| 544.6| 545.0| 545.4| 545.8| 546.2| 546.6| 547.0| 547.4| 547.8| 548.2| 548.6| 549.0| 549.4| 549.8
31| 550.2| 550.6| 551.0| 551.4| 551.8| 552.2| 552.6| 553.0| 553.4| 553.8| 554.2| 554.6| 555.0| 555.4| 555.8| 556.2| 556.6| 557.0| 557.4| 557.8
32| 558.2| 558.6| 559.0| 559.4| 559.8| 560.2| 560.6| 561.0| 561.4| 561.8| 562.2| 562.6| 563.0| 563.4| 563.8| 564.2| 564.6| 565.0| 565.4| 565.8
33| 566.2| 566.6| 567.0| 567.4| 567.8| 568.2| 568.6| 569.0| 569.4| 569.8| 570.2| 570.6| 571.0| 571.4| 571.8| 572.2| 572.6| 573.0| 573.4| 573.8
34| 574.2| 574.6| 575.0| 575.4| 575.8| 576.2| 576.6| 577.0| 577.4| 577.8| 578.2| 578.6| 579.0| 579.4| 579.8| 580.2| 580.6| 581.0| 581.4| 581.8
35| 582.2| 582.6| 583.0| 583.4| 583.8| 584.2| 584.6| 585.0| 585.4| 585.8| 586.2| 586.6| 587.0| 587.4| 587.8| 588.2| 588.6| 589.0| 589.4| 589.8
36| 590.2| 590.6| 591.0| 591.4| 591.8| 592.2| 592.6| 593.0| 593.4| 593.8| 594.2| 594.6| 595.0| 595.4| 595.8| 596.2| 596.6| 597.0| 597.4| 597.8
37| 598.2| 598.6| 599.0| 599.4| 599.8| 600.2| 600.6| 601.0| 601.4| 601.8| 602.2| 602.6| 603.0| 603.4| 603.8| 604.2| 604.6| 605.0| 605.4| 605.8
38| 606.2| 606.6| 607.0| 607.4| 607.8| 608.2| 608.6| 609.0| 609.4| 609.8| 610.2| 610.6| 611.0| 611.4| 611.8| 612.2| 612.6| 613.0| 613.4| 613.8
39| 614.2| 614.6| 615.0| 615.4| 615.8| 616.2| 616.6| 617.0| 617.4| 617.8| 618.2| 618.6| 619.0| 619.4| 619.8| 620.2| 620.6| 621.0| 621.4| 621.8
40| 622.2| 622.6| 623.0| 623.4| 623.8| 624.2| 624.6| 625.0| 625.4| 625.8| 626.2| 626.6| 627.0| 627.4| 627.8| 628.2| 628.6| 629.0| 629.4| 629.8
41| 630.2| 630.6| 631.0| 631.4| 631.8| 632.2| 632.6| 633.0| 633.4| 633.8| 634.2| 634.6| 635.0| 635.4| 635.8| 636.2| 636.6| 637.0| 637.4| 637.8
42| 638.2| 638.6| 639.0| 639.4| 639.8| 640.2| 640.6| 641.0| 641.4| 641.8| 642.2| 642.6| 643.0| 643.4| 643.8| 644.2| 644.6| 645.0| 645.4| 645.8
43| 646.2| 646.6| 647.0| 647.4| 647.8| 648.2| 648.6| 649.0| 649.4| 649.8| 650.2| 650.6| 651.0| 651.4| 651.8| 652.2| 652.6| 653.0| 653.4| 653.8
44| 654.2| 654.6| 655.0| 655.4| 655.8| 656.2| 656.6| 657.0| 657.4| 657.8| 658.2| 658.6| 659.0| 659.4| 659.8| 660.2| 660.6| 661.0| 661.4| 661.8
45| 662.2| 662.6| 663.0| 663.4| 663.8| 664.2| 664.6| 665.0| 665.4| 665.8| 666.2| 666.6| 667.0| 667.4| 667.8| 668.2| 668.6| 669.0| 669.4| 669.8
46| 670.2| 670.6| 671.0| 671.4| 671.8| 672.2| 672.6| 673.0| 673.4| 673.8| 674.2| 674.6| 675.0| 675.4| 675.8| 676.2| 676.6| 677.0| 677.4| 677.8
47| 678.2| 678.6| 679.0| 679.4| 679.8| 680.2| 680.6| 681.0| 681.4| 681.8| 682.2| 682.6| 683.0| 683.4| 683.8| 684.2| 684.6| 685.0| 685.4| 685.8
48| 686.2| 686.6| 687.0| 687.4| 687.8| 688.2| 688.6| 689.0| 689.4| 689.8| 690.2| 690.6| 691.0| 691.4| 691.8| 692.2| 692.6| 693.0| 693.4| 693.8

Channel Assignments by Region

Post Office Box 576
E7556 State Rd. 23 and 33
Reedsburg, Wisconsin 53959 USA
support@sounddevices.com
+1 608.524.0625 main
800.505.0625 toll free (U.S. only)
www.sounddevices.com

References

• Home - Sound Devices

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>