LNC L2AUEQE5231D9C 1 Light 11.8 in Polished Gold with Clear Glass LED Instruction Manual

LNC L2AUEQE5231D9C 1 Light 11.8 in Polished Gold with Clear Glass LED

Item Number: A05231

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

ACCESSORIES & QTY ENCLOSED:

OUTLET BOX

• (A) Plastic wire connector (3)
• (B) Mounting screw (2)
• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Canopy screw (2)
• (F) Canopy (1)
• (G) Decorative metal (2)
• (H) Socket assembly (1)
• (I) Pipe (1)
• (J) Lampshade (1)
• (K) Metal gasket (2)
• (L) Plastic gasket (2)
• (M) Nut (1)
• (N) Lid (1)
• (O) Lid nut (1)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

3. Unscrew canopy screws (E) from mounting plate (C).

4. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

5. To secure the unit as shown in the illustration:

6. Open decorative metals (G).

7. Hang up lampshade (J) .

8. Screw one of metal gasket (K), one of plastic gasket (L), the another plastic gasket (L) , the another metal gasket (K), nut (M) and lid (N) to nipple of pipe (I), and then screw lid nut (O) to the nipple to secure lampshade (J).
   When installing, please follow the order of the above text or as shown in the illustration.

9. Secure mounting plate (C) to the outlet box with mounting screws (B).
   NOTE: the side of mounting plate (C) marked “GND” must face out.

10. Make wire connections
    Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the chart below
    Connect wires according to the chart below
    Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
    Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

11. Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening canopy screws (E) onto the pre-assembled threaded nipple on mounting plate (C).
    Note: canopy (F) should be snug against the ceiling and canopy screws (E).
    If not, adjust the threaded length on mounting plate (C):

    • First, unscrew the pre-assembled hex nuts.
    • Then, screw the pre-assembled screws in or out of mounting plate (C).
    • When the secure length is achieved, tighten the hex nuts and back to step 8.

12. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>