YESOUL YS-002 M1 Bluetooth Fitness Bike Installation Guide
- August 14, 2024
- YESOUL
Table of Contents
- YESOUL YS-002 M1 Bluetooth Fitness Bike Installation Guide
- Product Parameters
- Important Safety Instructions
- Installation Guide ——— List of Par
- First Use
- How to Adjust Bike
- How to Determine Correct Riding Posture
- Routine Maintenance
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
YESOUL YS-002 M1 Bluetooth Fitness Bike Installation Guide
Product model: YS-002
This device contains a radio transmission module with model approval code
CMIIT ID: 2021DP4016.
Before using this pr oduct, carefully r ead and properly k eep this manual.
Product Parameters
Important Safety Instructions
Please read them carefully. Improper use may result in personal injury or death!
- Make sure that the saddle height adjustment knob is secured correctly, and will not affect motion during exercise.
- Keep children and pets away from this product. This product is for those over 16 years old only.
- Never stretch any object or body part into the openings of the bike.
- The weight of the user must not exceed the maximum load.
- Get off the bike until flywheel and pedals stop rotating. Otherwise, severe injuries may be caused due to control failure.
- If you feel any discomfort, such as dizziness or breathing difficulty, stop riding the bike and carefully get off.
- Never turn pedals by hand or touch any rotating mechanical part; otherwise, personal injury may be caused.
- Keep the body hydrated as needed during riding.
- Use this product according to the instructions in this manual. Warm up fully before exercise.
- Without the preliminary determination of baseline fitness level and medical certificate signed by a doctor, never be engaged in high-speed or high-intensity sports. Before attempting any high-intensity short sprints, pay attention to the body state and posture, and apply a controllable speed.
- Wear professional cycling clothes or tight-fitting sportswear and sports shoes, and tighten foot straps to avoid injury caused by pulling or entanglement by this product.
- Never use this product with inappropriate shoes or barefoot.
- Incorrect or excessive training may cause injury.
- Check whether the bike for loosening or damage before each use.
- Never refit this bike or use non-original accessories without permission. The casing must be opened by professionals, in order to avoid damage.
- Those pregnant or with high blood pressure, heart disease, lumbar spondylosis or reduced mobility must not use this product without the permission of doctors.
- In case of any discomfort such as dizziness or chest pain during exercise, stop exercising immediately and go to a hospital for examination.
- If the product fails, immediately stop using it.
- This product must not be used for medical rehabilitation.
- Use this product on a flat and clean ground.
- Carry out preventive maintenance regularly.
- Never expose this product in a humid place. This product must not be used outdoor or in any humid place.
- The product should have at least 0.5 meters of free space all around it.
Installation Guide ——— List of Par
STEP1: Check of parts
Installation Guide – List of Parts
*In order to facilitate assembly, some accessories have been installed on the body before delivery.
STEP 2: Installation of bottom tube
1. Take L-type hex wrench 5# (A) out of the ziplock bag.
2. Remove four M8 × 45 cushion bolt of the front tube ② and rear tube ③ via
the wrench.
3. Align the hole of the front and rear tubes with the bottom holes of the frame①, manually screw the front and rear tubes into frame, and tighten it via the L-type hex wrench 5# (A).
STEP 3: Installation of bottle holder
1. Take the L-type hex wrench 5# (A) out of the ziplock bag.
2. Remove two screws (M6×12) of the dual-purpose bracket ⑥ via the wrench.
3. Insert the bottle holder ⑧ along the slot into the dual-purpose bracket. Align the hole of the bottle holder with that of the bracket ⑥, manually install two screws (M6×12) into holes, and tighten them via the L-type hex wrench 5# (A).
STEP 4: Installation of handlebar and dual-purpose bracket
1. Remove four screws (M6×12) of the riser via the L-type hex wrench 5# (A).
2. Align the holes of the handlebar ⑤ with those of the riser, manually install screws into two rear holes (without tightening), and insert the dual- purpose bracket ⑥ into the round hole of the handlebar ⑤ as indicated by the arrow. Then manually install the other two screws and one long hexagon socket cap screw (B, in the ziplock bag) into three corresponding holes (without tightening). Finally, vertically tighten five screws down via the L-type hex wrench 5# (A), and press down the decorative cover ⑨ of the handlebar. Thus, the handlebar installation is completed.
STEP 5: Installation of tablet (mobile phone) holder
1. Remove two screws (M6×12) and elastic washers of the dual-purpose bracket
⑥ via the L-type hex wrench 5# (A).
2. Align the holes of the tablet holder ⑦ with those of the dual-purpose bracket ⑥, manually install screws (M6×12) and tighten them via the L-type hex wrench 5# (A).
STEP 6: Pedal installation
- Take out the pedal assemblies L and R④.
- Separate the pedal assemblies L and R④.
- Lock the pedal assembly L④ into the left crank, and tighten with the open-ended wrench(C) along the direction indicated by the arrow.
- Lock the pedal assembly R④ into the right crank, and tighten with the open-ended wrench (C) along the direction indicated by the arrow.
Safety tips:
Reverse riding is not recommended, as it is likely to loosen pedals. After
reverse riding, check whether the pedals are locked, in order to avoid safety
issues arising from loose pedals.。
STEP 7: Battery Dismantling and Installation
Tip: If the resistance change is inconsistent with the resistance change in APP after the resistant knob is turned, press the buttons A and B to correct it.
Safety tip:
Adjust the bike and tighten the body tightening knob as needed before using
it.
Statement:
This manual contains the functional introduction and operating instructions as
much as possible when printed.
With the continuous improvement of hardware and software and optimization of
design, this manual may be inconsistent with the purchased product.
In case of any discrepancy in appearance, interface and color, the actual
product shall prevail.
First Use
APP installation and registration
1. Scan the QR code to download the APP, and register an APP account.
2. Upon registration, open the bike course in the APP. Please connect the
bike according to the interface prompts in the course for the first use. Then,
once you ride the bike, the exercise mode of the APP will be enabled or the
course will be automatically accessible.
3. Before connecting the APP with bike, make sure that the Bluetooth of your
mobile phone/tablet PC has been enabled and no other devices are connected.
About APP membership
Registered users can get the membership free of charge on the product
membership page as indicated on the interface.
- After the first connection, the APP will automatically match the bike. Directly ride the bike when it is used for the second time.
- The bike does not support the simultaneous connection of multiple mobile phones. Before using this product, make sure that other users are not connected to the bike.
- The bike will be disconnected 10 min after riding.
- In addition to connection with YESOUL APP, the Bluetooth can also be connected with kinomap and zwift software.
*Due to software upgrades, the actual product will prevail.
How to Adjust Bike
1 .Handlebar height adjustment:
Loosen and pull out the front column knob with one hand, hold the middle part of the handlebar with the other hand, and lift the handlebar to the desired position. Then release the knob, and gently pull the column up and down until the spring is automatically reset (when a“ click” sound is heard, it means that the knob has been clamped in the hole of the column). Tighten the knob as much as possible.
2 .Saddle height adjustment:
Loosen and pull out the rear column knob with one hand, and lift (or press)
the saddle with the other hand to the desired position. Loosen the knob and
gently pull the column up and down until the spring is automatically reset
(when a“ click” sound is heard, it means that the knob has been clamped in the
hole of the column). Tighten the knob as much as possible.
3. Horizontal adjustment of saddle:
Loosen the knob under the saddle, slide the saddle back and forth to the
desired position, and tighten the knob as much as possible.
4. Body level adjustment:
There are four adjustment pads at the bottom of the front and rear pedal tubes. Screw these pads until they are tightly secured on the floor and the body does not shake.
How to Determine Correct Riding Posture
1. Setup of correct saddle position
Saddle height
Put the feet together, stand on one side of the saddle and adjust the saddle
to the hip height (Fig.
1). Then site on the saddle, and step on the pedals forcibly until they are
stopped at 6 o’clock and the leg can be fully stretched (Fig. 2).
Horizontal position of saddle
Put the right foot into the clamp, and step on the pedals, until the right
pedal is at 3 o’clock and the front side of the knee joint is on the same
vertical line as the pedal, that is, the saddle is in the correct position
(Fig. 3).
2. Setup of appropriate handlebar height
Each user can set up the appropriate handlebar height based on his or her body
height and riding experience.
Recommendation: The handlebar should be slightly higher than the saddle for
new users (Fig. 1) and flush with or slightly lower than the saddle for
experienced users (Fig. 2).
Users subject to lumbar muscle strain and lumbar spondylosis may ride the bike
with the consent of doctors. It is recommended to adjust the handlebar into a
higher position.
3. Handle position layout of bike
During riding, coaches will show the corresponding hand positions, i.e. the
corresponding parts of the handlebar, as shown below.
Routine Maintenance
Daily use:
Keep the bike on a dry, ventilated and flat floor. If not used in a long time,
the bike should be covered to keep its body clean and tidy.
Frame maintenance:
Wipe off sweat on the frame with cloth after exercise. Do not wipe the bike
with wet cloth, in order to avoid rusting.
Belt maintenance:
Check the belt pulley for cracking and deviation, and adjust or replace the
belt in time. Regularly clean the belt groove to prevent the belt from jumping
out of the groove.
Inspection of body screws:
Always check the screws of all body parts for loosening or falling, and
tighten or replace them in time.
Inspection of resistance adjustment knob:
Always check the resistance adjustment knob for loosening or falling. Check
whether the resistance is reasonable, so as to calibrate resistance in time.
Inspection of pedals and cranks:
Always check the screws of pedals and cranks for loosening, and tighten them
in time.
Saddle maintenance:
Always check whether the saddle is loose and tighten it in time. Wipe the
saddle with cotton cloth to keep it dry.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>