ZENIKO OT40 Bi Pro Color Inflatable LED Tube Light Installation Guide

ZENIKO OT40 Bi Pro Color Inflatable LED Tube Light

Name of Parts

What’s Inside

Note: Due to continuous updates and upgrades of the products, there may be differences between the actual products and the pictures. Therefore, the pictures are for reference only, products to prevail in kind.

Instruction for Inflation

Open the air valve lid in power off status, insert the air pump into the air valve port, and press it continuously to inflate the light body, then close the lid after fully inflated.

Instruction for Deflation

Open the air valve lid in power off status, and press the deflating device in the middle of the air valve to deflate the light body gradually.

Power Switch
This light has two power-on modes: a power switch button and a plug-and-play (no need to press the power switch button). The factory default is to press the power switch button to start, i.e., connect the light to a DC power source with a USB-C male plug, then press the power switch button to turn it on/off. Press and hold the power switch button for 1.5s in the power-off state, you can switch between the two power-on modes.

Brightness Adjustment
Short press the + button in power on status to increase the brightness, while short press the – button to decrease the brightness. The brightness is adjustable in 10 levels: 10%, 20%, 30%, 40%, 50%, 60%, 70%, 80%, 90% and 100%.

CCT Adjustment
Short press the COLOR button in power on status to switch CCT in 5 levels in recycle: 3000K, 3800K, 4600K, 5600K and 6500K.

Power Identification
When the light cannot be turned on with the last memorized power due to insufficient power supply, short press the power switch button three times (do not press continuously), it will boot up at the lowest brightness and the last saved color temperature.

Factory Reset
Press and hold the +/- button for 1.5 seconds at the same time, and the light body will boot up at the lowest brightness and lowest color temperature.

Technical Data

Declaration of Conformity

Zeniko Technology Co., LTD hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU. They are allowed to be used in all EU member states.

For more information of DoC, Please click this web link:

• https://www.zeniko.com/EU/OT40BIPRO.PDF
• https://www.zeniko.com/EU/OT80BIPRO.PDF

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it safe. Thank you!

Applicable Products
The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways, and additional accessories attached, etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day (purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered onthe warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by an external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding, and damp environments, etc;
3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alteration, addition, and detachment;
4. The original identifying information of the product or accessory is modified, alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard, or non-public released software;
7. Breakage or damage caused by force majeure or accident;
8. Breakage or damage that could not be attributed to the product itself. Once these situations are met, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that are beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion, and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Zeniko Technology Co., LTD

• Add.: 1208 Room, Jinshan Building, No.5033, Shennan East Road, Xinwei Community, Guiyuan Street, Luohu District, Shenzhen City
• Tel: +86-755-25106331
• www.zeniko.com
• Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>