YESOUL YS-003 Smart Cycling Bike Owner’s Manual

June 10, 2024
YESOUL

V1 YESOUL BIKEYESOUL YS 003 Smart Cycling Bike

YS-003 Smart Cycling Bike

Before using this product, carefully read  and properly keep this manual.

Product model: YS-003
YESOUL BIKE
V1 Product Manual
YESOUL BIKE VI. YESOUL YS 003 Smart Cycling Bike

Product Parameters

Tablet (mobile phone) holder
size| Maximum tablet width: 260mm
---|---
Supporting software version| iOS 10.0 or higher, Android 5.0 or higher
Resistance system| Magnetron resistance system
Drive mode| Belt drive
Power supply| Button battery (model: CR2477)
Height limit| 150-195cm
Rated maximum load| 120kg
Net weight| 45 kg
Gross weight| 48 kg
Overall dimensions| (Length) 1450mm x (Width) 530mm x (Height) 1300 mm

Important Safety Instructions

Please read them carefully. Improper use may result in personal injury or death!

  1. Make sure that the saddle height adjustment knob is secured correctly, and will not affect motion during exercise.
  2. Keep children and pets away from this product. This product is for those over 16 years old only.
  3. Never stretch any object or body part into the openings of the bike.
  4. The weight of the user must not exceed the maximum load.
  5. Get off the bike until flywheel and pedals stop rotating. Otherwise, severe injuries may be caused due to control failure.
  6. If you feel any discomfort, such as dizziness or breathing difficulty, stop riding the bike and carefully get off.
  7. Never turn pedals by hand or touch any rotating mechanical part; otherwise, personal injury may be caused.
  8. Keep the body hydrated as needed during riding.
  9. Use this product according to the instructions in this manual. Warm up fully before exercise.
  10. Without the preliminary determination of baseline fitness level and medical certificate signed by a doctor, never be engaged in high-speed or high-intensity sports. Before attempting any high-intensity short sprints, pay attention to the body state and posture, and apply a controllable speed.
  11. Wear professional cycling clothes or tight-fitting sportswear and sports shoes, and tighten foot straps to avoid injury caused by pulling or entanglement by this product.
  12. Never use this product with inappropriate shoes or barefoot.
  13. Incorrect or excessive training may cause injury.
  14. Check whether the bike for loosening or damage before each use.
  15. Never refit this bike or use non-original accessories without permission. The casing must be opened by professionals, in order to avoid damage.
  16. Those pregnant or with high blood pressure, heart disease, lumbar spondylosis or reduced mobility must not use this product without the permission of doctors.
  17. In case of any discomfort such as dizziness or chest pain during exercise, stop exercising Immediately and go to a hospital for examination.
  18. If the product fails, immediately stop using it.
  19. This product must not be used for medical rehabilitation.
  20. Use this product on a flat and clean ground.
  21. Carry out preventive maintenance regularly.
  22. Never expose this product in a humid place. This product must not be used outdoor or in any humid place.

Installation Guide – List of Parts

STEP 1: Check of parts List of Parts

Parts List (Components List) NO. Name Quantity Picture
1 Front ground pipe assembly 1
2 Rear ground pipe assembly 1
3 Hexagon socket button head screw M8T1.25’50L 4
4 Elastic washer 8’2.1t 6
5 Flat washer M8 (D16 x d8.5 x 1.50 4
6 Handle 1
7 Hexagon socket button head screw M8’P1.25’16L 6
8 Screen bracket 1
9 Bottle holder 1
10 Hexagon socket button head screw M6’171.0’101 2
Parts List (Components List) NO. Name Quantity Picture
12 Tablet (mobile phone) holder 1
12 Hexagon socket cap screwM6°P1.0′ 121M5P1.0121 2
13 Pedal set left/right 1
14 Dumbbell set (lkg/EA) 2
15 Elastic washer 6’1.6t 2
Accessories List (Tools List) NO. Name Quantity

Picture
---|---|---|---|---
A| Hex key 4mm/70LX25L| 1|
B| Hex key 5mm/100LX3OL| 1|
C| Box-ended wrench 8/10mm| 1|
D| Box-ended wrench 13/14/15/17 mm| 1|

In order to facilitate assembly, some accessories have been installed on the body before delivery.

Installation Guide

STEP 2: Install ground pipes

  1. Install the front ground pipe assembly0, and tighten it with the hex key (B), as shown in the figure.
  2. Lock it with two sets of hexagon socket button head screw ® and flat washer as shown in the figure, make sure to lock the pipe tightly; otherwise, it may result in deformation.
  3. Check and confirm the adjusting footpad is fully locked into the front ground pipe assembly .

YESOUL YS 003 Smart Cycling Bike - Pipe

  1. Install the rear ground pipe assembly Q, and tighten it with the hex key (B), as shown in the figure.
  2. Lock it with two sets of hexagon socket button head screw ® and flat washer ® as shown in the figure, make sure to lock the pipe tightly; otherwise, it may result in deformation.
  3. Check and confirm the adjusting footpad is fully locked into the rear ground pipe assembly.

YESOUL YS 003 Smart Cycling Bike - Pipe 1

STEP 3: Assemble handle
Place the handle 4 on the handle bracket, and lock the same with 4 sets of elastic washers  4 and hexagon socket button head screws 7 via the hex key (B).

YESOUL YS 003 Smart Cycling Bike - Pipe 2Load the screen bracket 4 onto the fixed seat, and lock the same onto the stand column with 2 sets of hexagon socket button head screws and elastic washers7  via the hex key (B).

YESOUL YS 003 Smart Cycling Bike - Pipe 3

STEP 4: Install bottle holder
As shown in the figure, clip the bottle holder® by the middle under the screen bracket ®, and lock the same onto the bracket with 2 sets of Hex socket screws®.YESOUL YS 003 Smart Cycling Bike - Pipe 4 STEP 5: Installation of tablet (mobile phone) holder
Take out the PAD (cellphone) holder ®, align the support on the back of the holder with the screen bracket, lock two sets of elastic washer and hexagon socket screw 15 on the bracket via the hex key (B).

YESOUL YS 003 Smart Cycling Bike - Pipe 5

STEP 6: Pedal installation ].

  1. Takeout the pedal assembly ifb.
  2. Pay attention to distinguish left pedal and right pedal.
  3. Lock the left pedal assembly 61, into the left crank,and tighten with the box-ended wrench (D) along the direction indicated by the arrow.
  4. Lock the right pedal assembly IP into the right crank, and tighten with the box-ended wrench (D) along the direction indicated by the arrow.
    Screw the pedal into the crank manually first, and then tighten the left/right pedal assembly i3 with the box-ended wrench (D). (Note: The tightening directions for both the left pedal and the right pedal are towards the head direction.)YESOUL YS 003 Smart Cycling Bike - Pipe 6

Safety tips: Reverse riding is not recommended, as it is likely to loosen pedals. After reverse riding, check whether the pedals are locked, In order to avoid safety issues arising from loose pedals.
STEP 7: Battery Dismantling and Installation

  1. If the bike is provided with a battery. pull the insulation strip out of the gap of the battery other before using this product
  2. When batten/replacement is required, remove the two cruciform slot screws on the electronic control plate, and pull out the plate from the back (do not pull hard for the power cord on the back are connected to the cycle body), remove the used battery, load the new battery into the battery holder with the positive pole facing upwards (-+” mark facing upwards), close the cover, and tighten the screws.YESOUL YS 003 Smart Cycling Bike - Pipe 7

Safety tips: Please adjust the back according to your physical condition before use; and tighten the body fastening knob.

YESOUL YS 003 Smart Cycling Bike - Pipe 8

Statement:
This manual contains the functional introduction and operating instructions as much as possible when printed. With the continuous improvement of hardware and software and optimization of design, this manual may be inconsistent with the purchased product. In case of any discrepancy in appearance, interface and color, the actual product shall prevail.

Initial use (APP download)

Scan the QR code to download YESOUL APP

YESOUL YS 003 Smart Cycling Bike - QR

http://www.yesoulchina.com/dl.html?apptype=S3Download| http://www.yesoulchina.com/dl.html?apptype=home

APP installation and registration

  1. You can scan the QR code above to download the Chinese or international version of APP, and register an APP account.
  2. Upon registration, open the bike course in the APR Please connect the bike according to the interface prompts in the course for the first use. Then, once you ride the bike, the exercise mode of the APP will be enabled or the course will be automatically accessible. 3, Before connecting the APP withbike, make sure that the Bluetooth of your mobile phone/tablet PC has been enabled and no other devices are connected.

About APP membership

  1. Newly registered users of the Chinese version of APP-Yesoul will get the membership free of charge granted along with the bike. The number and rights of membership granted vary depending on the models of bike. Please consult customer service personnel before purchasing the bike. (If you didn’ t receive this freebie automatically, you may get it by manually typing in the SN code: Under [My] page, tap on Become a Member Now under the portrait to access the membership page. Tap on Redeem Membership to the upper right, enter the SN code on your machine, and you are now a member.)
  2. Registered users of the international version of APP-Yesoul Sports can get the membership free of charge on the product membership page as indicated on the interface.YESOUL YS 003 Smart Cycling Bike - Pipe 10 *Due to software upgrades, the actual product will prevail.

How to Adjust Bike

  1. Handlebar height adjustment: Loosen, pull out and hold the front column knob with one hand, hold the middle part of the handlebar with the other hand, and lift the handlebar to the desired position. Then release the knob, and gently pull the column up and down until the spring is automatically reset (when a “click” sound is heard, it means that the knob has been damped in the hole of the column). Tighten the knob as much as possible.YESOUL YS 003 Smart Cycling Bike - Pipe 11
  2. Saddle height adjustment: Loosen, pull out and hold the rear column knob with one hand, and lift (or press) the saddle with the other hand to the desired position. Loosen the knob and gently pull the column up and down until the spring is automatically reset (when a “click” sound is heard, it means that the knob has been clamped in the hole of the column). Tighten the knob as much as possible.YESOUL YS 003 Smart Cycling Bike - Pipe 12
  3. Horizontal adjustment of saddle: Loosen the knob under the saddle, slide the saddle back and forth to the desired position, and tighten the knob as much as possible.YESOUL YS 003 Smart Cycling Bike - Pipe 13
  4. Body level adjustment: There are four adjustment pads at the bottom of the front and rear pedal tubes. Screw these pads until they are tightly secured on the floor and the body does not shake.YESOUL YS 003 Smart Cycling Bike - Pipe 14

How to Determine Correct Riding Posture

  1. Setup of correct saddle position Saddle height Put the feet together, stand on one side of the saddle and adjust the saddle to the hip height (Fig. 1). Then site on the saddle, and step on the pedals forcibly until they are stopped at 6 o’ clock and the leg can be fully stretched (Fig. 2).YESOUL YS 003 Smart Cycling Bike - Pipe 15 Horizontal position of saddle
    Put the right foot into the clamp, and step on the pedals, until the right pedal is at 3 o’ clock and the front side of the knee joint is on the same vertical line as the pedal, that is, the saddle is in the correct position (Fig. 3).YESOUL YS 003 Smart Cycling Bike - Pipe 16

  2. Setup of appropriate handlebar height Each user can set up the appropriate handlebar height based on his or her body height and riding experience. Recommendation: The handlebar should be slightly higher than the saddle for new users (Fig. 1) and flush with or slightly lower than the saddle for experienced users (Fig. 2). Users subject to lumbar muscle strain and lumbar spondylosis may ride the bike with the consent of doctors. It is recommended to adjust the handlebar into a higher position.YESOUL YS 003 Smart Cycling Bike - Pipe 16

  3. Handle position layout of bike
    During riding, coaches will show the corresponding hand positions, i.e. the corresponding parts of the handlebar, as shown below.YESOUL YS 003 Smart
Cycling Bike - Pipe 18 • Hand position
    • Q Hand position
    • Q Hand position 3

Routine Maintenance

Daily use:
Keep the bike on a dry, ventilated and flat floor. If not used in a long time, the bike should be covered to keep its body clean and tidy. Frame maintenance: Wipe off sweat on the frame with cloth after exercise. Do not wipe the bike with wet cloth, in order to avoid rusting. Belt maintenance: Check the belt pulley for cracking and deviation, and adjust or replace the belt in time. Regularly clean the belt groove to prevent the belt from jumping out of the groove. Inspection of body screws: Always check the screws of all body parts for loosening or falling, and tighten or replace them in time. Inspection of resistance adjustment knob: Always check the resistance adjustment knob for loosening or falling. Check whether the resistance is reasonable, so as to calibrate resistance in time. Inspection of pedals and cranks: Always check the screws of pedals and cranks for loosening, and tighten them in time. Saddle maintenance: Always check whether the saddle is loose and tighten it in time. Wipe the saddle with cotton cloth to keep it dry.

YESOUL Icon

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

YESOUL User Manuals

Related Manuals