PROJECT X OFFROAD GB538824 Ghost Box Wireless Control Instructions
- June 5, 2024
- PROJECT X OFFROAD
Table of Contents
Model No. GB538824
IMportant safety Information
- SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
- Before using this product, read all instructions and cautionary markings.
- Do not expose the keypad to rain, moisture, or snow.
- Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric
- Do not operate with a damaged keypad or ghost box replace it immediately.
- Do not operate the keypad or ghost box if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified service person.
- Do not disassemble the keypad or ghost box; take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
- To reduce the risk of electric shock, unplug the keypad or ghost box before attempting any maintenance or cleaning. Turning off controls will not reduce this risk
info@projectxoffroad.com
866-294-9244
Mon-Sat 8 am-5 pm PST
Technical Specifications
Input Voltage: 9-16V DC
Maximum Current: 0.075A @12V DC
Maximum Power: 0.9W @ 12V DC
Operating Temp: -22°F to 149°F
Storage Temp: -40°F to 185°F
Waterproof Rating: IP65
Wireless Frequency: 2.4GHz & Bluetooth 5.0
Wireless Range (RF Wifi): 98.4 Feet without interference or
obstruction)
Wireless Range (Bluetooth®): 33 Feet without interference or obstruction)
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc., and any use of such marks by ADC Solutions Auto, LLC is under license. Other trademarks and trade names are those of their respective owners.
Includes
1x KEY PAD
1x Power Cable
1x M5 Screw (L50mm)
2x M6 Washer (OD:12mm / ID 6.5mm
2x M6 Nut
1x Keypad Button Sticker
4x 3M VHB Double Sided Tape
Cautions
Check your state or provincial laws before installing. Vehicle owners must
comply with all applicable laws.
This product is intended solely for off-road purposes. Manufacturer and Seller
assume no liability for installation or use, which are solely the
responsibility of the purchaser. This product is not DOT approved and is
designed and intended for off-road uses only.
- Do not install or use product if it, in any way, impairs the safe operation of your vehicle.
- Follow manufacturer’s instructions to ensure the product is properly and safely installed.
- Check your state or provincial laws before installing. Vehicle owners must comply with all applicable laws.
- This product is intended solely for off-road purposes. Manufacturer and Seller assume no liability for installation or use, which are solely the responsibility of the purchaser.
- This product is not DOT approved and is designed and intended for off-road uses only.
- The Manufacturer and Seller are not responsible or liable for consequential, incidental, or indirect damages, whether to person or property, resulting from the installation or improper use of this product.
Warranty
This PROJECT X product carries a Limited Lifetime warranty against defects in
workmanship and materials subject to the conditions and additional warranty
information available at:
www.projectxoffroad.com/pages/returns-
warranty
DISCLAIMER OF WARRANTIES, INCLUDING WARRANTY OF MERCHANTABILITY AND WARRANTY OF FITNESS FOR PARTICULAR PURPOSE: EXCEPT AS SPECIFICALLY SET FORTH HEREIN, NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, IS MADE AS TO THE GHOST BOX. PROJECT X AND/OR ITS AFFILIATES EXPRESSLY DISCLAIMS, WITHOUT LIMITATION, ANY STATUTORY WARRANTIES AND ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
PROJECT X
2975 Red Hill Ave., Ste.
100, Costa Mesa, CA 92626, USA
FCC Compliance statement
This device comply with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications or change to this equipment.
Such modifications or change could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital devices, pursuant to part 15 of the FCC Rules. These
limits aredesigned to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet general RF exposure requirements, This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>