PANOWIN F1 Laser Head User Manual
- June 7, 2024
- PANOWIN
Table of Contents
PANOWIN F1 Laser Head User Manual
WARNING
Caution: 4 class laser. Always
wear protective goggles when in use. Laser can provoke serious and permanent
damage to the naked eye.
Laser Radiation Avoid Direct Eye Exposure.
Wavelength 400-450nm Class IV Laser Product.
This product complies with 21CFR
Danger!
Avoid Exposure! Laser light is emitted from this aperture.
WARNING: Take necessary protection
before operating on the Laser Head.
WARNING: Make sure the Power is
OFF before assembling the Laser Head and connecting the cable.
CAUTION: In case of emergency unplug the Panowin F1 from the power outlet.
WARNING: Carefully monitor the Panowin F1 during operation. Do not leave unattended.
WARNING: The Panowin F1 contains moving parts that can cause injury. Keep hands, body parts, loose clothing, pets and children
Assembly Instructions
Step 1: Assemble the Laser Head Holder to the mount middle plate.
Step 2: Fix the Laser Head Holder by screws and put the Laser Head onto the holder.
Step 3: Connect the cable to the Laser interface of the main control
board.
Warning: Make sure the power is off while connecting the cable!
Step 4: Work with the engraving software.
Warning: Take necessary protections while operating!
Step 5: Pango Laser engraving Fuction:
Cautions: Please make sure your 3D printer installed the laser attachment
properly, and engraving function.
- Go to “Preference — Preferences” , set the printer as ” Panowin F1 Laser” mode. After restart the Pango you can enter the laser mode.
- Go to ‘Model—Load” or click MODEL icon in the tools bar, select a .jpg or .png file
And the platform will appear the
image of laser engraving or laser path of laser cutting
Laser engraving
Laser cutting
-
Go to ‘Model- – -Save Code.’ or click save code icon on the tools bar, save the .pcode file in the SD card.
-
Inset the SD card into printer and start printing.
Please fix the engraving material stably on the platform.
Step 6: Setting
Cautious: Avoid any part of body contact with laser beam. (Children under
15 years old are not allowed to use the laser function.)
Please install the enclosure or wear the shield glasses before start
engraving.
Go to ” —Settings” to open the parameter setting page.
Printing speed: Laser engraving or cutting speed. Higher the speed. shorter the engraving/cutting time, lighter the engraving trace. Slower the speed, longer the engraving/cutting time. deeper the engraving trace.
Laser at Height: The distance between laser and platform. The distance should be same with the laser focus length to reach the best engraving quality. The laser focus distance could be adjusted by adjusting the laser lens.
Laser Mode Cut: Pango will analyse the image edge and scale and fill it with vector line. Can be used for the simple logo or vector file engraving.
Laser Mode Carve: Pango will transform the image into bitmap. Can be used for photograph engraving.
Bright Threshold: The cutting mode will transform the colored picture into black and white. The bright threshold value will set the demarcation of the black and while.
Reversed Bright: Reverse the black and white.
Infill Rate: Infill rate of the laser cutting mode.
Infill speed: Engraving speed of the laser cutting mode.
Copyright Notice
Panowin copyrights this manual. No part of this manual may be reproduced in any form or means. without the prior written consent of Panowin.
Copyright © 2013. Panowin Technologies. Co.. Ltd. All Rights Reserved.
Disclaimer
This manual is preliminary and is subject to change at any time without notice. Panowin assumes no responsibility for any errors contained herein.
Tele : 021-60950805 021-60950806
Fax : 021-60950807
Email : service@panowin.com
Website : www.panowin.com
Wechat : panowin_3dp
Address : Room 1019. Building 69. 100 Handan Road. Yangpu District.
Shanghai. China
Website
Wechat
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>