JBL A55BT Bluetooth Headphone User Manual

JBL A55BT Bluetooth Headphone

PACKAGE CONTENTS

OVERVIEW – BUTTONS & LED

BLUETOOTH PAIRING

POWERING ON

• Long press the Power button for more than 3 seconds Headphone beeps “power on” tone
• NOTE: Headphone will automatically enter the pairing mode when switched on for the first time.
• Long press Power button (more than 5seconds) to force enter Bluetooth pairing mode LED starts to flash red/blue alternately
• Activate the Bluetooth feature on your phone or music player, and set it to search for Bluetooth devices
• Select “Land Rover headphones” from the list of found devices on your phone or music player
• Once pairing is complete LED will flash blue.

USER INTERFACE (BT MODE)

VOLUME UP / DOWN

• Increase volume by 1 step Short Press (<1.5s) Voice +
• Decrease volume by 1 step Short Press (<1.5s) Voice –
• Empty PDL (Paired Device List) Vvlong Press (>=5s) VOL+ & VOL –

First paired device auto-reconnect feature:

The first device stored in the headphone pairing list will automatically reconnect if Bluetooth device is active when headphones are powered on (recommend to pair headphones to the vehicle on initial use).

CHARGING MODE

MODEL NAME: A55BT Bluetooth

•  FREQUENCY RESPONSE: 10HZ – 22KHZ
•  IMPEDANCE: 32 OHMS
•  MAX INPUT POWER: 30MW
•  SENSITIVITY: 111DB SPL/V@1KHZ
•  WEIGHT: 350 G
•  CABLE LENGTH: 1.5M
•  CONNECTION: Type C to Type C
•  BATTERY TYPE: LITHIUM-ION POLYMER. (3.7V, 600MAH)
•  CHARGING: 5VDC, 600MA
•  BLUETOOTH VERSION: 5.0
•  SUPPORT:A2DP V1.3, AVRCP V1.6.
•  BLUETOOTH TRANSMITTER FREQUENCY RANGE: 2402 − 2480MHZ
•  BLUETOOTH TRANSMITTER POWER: <4DBM
•  BLUETOOTH TRANSMITTER MODULATION: GFSK, Π/4 DQPSK, 8DPSK

Bluetooth

The Bluetooth word mark and logos are registered trademarks Owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FORA CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE INA RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED INACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE OF THE FOLLOWING MEASURES:

This Class B digital apparatus complies with Canadian ICES-003.
INSTRUCTIONS FOR USERS ON REMoVAL, RECYCLING AND DISPOSAL OF USED BATTERIES FOR PRODUCTS WITH A BUILT-IN BATTERY THAT LASTS FOR THE LIFETIME OF THE PRODUCT, REMOVAL MAY NOT BE POSSIBLE FOR THE USER. IN THIS CASE, RECYCLING OR RECOVERY CENTERS HANDLE THE DISMANTLING OF THE PRODUCT AND THE REMOVAL OF THE BATTERY. IF, FOR ANY REASON, IT BECOMES NECESSARY TO REPLACE SUCH A BATTERY, THIS PROCEDURE MUST BE PERFORMED BY AUTHORIZED SERVICE CENTERS. IN THE EUROPEAN UNION AND OTHER LOCATIONS, IT IS ILLEGAL TO DISPOSE OF ANY BATTERY WITH HOUSEHOLD TRASH. ALL BATTERIES MUST BE DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER. CONTACT YOUR LOCAL WASTE-MANAGEMENT OFFICIALS FOR INFORMATION REGARDING THE ENVIRONMENTALLY SOUND COLLECTION, RECYCLING AND DISPOSAL OF USED BATTERIES WARNING: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. TO REDUCE RISK OF FIRE OR BURNS, DON’T DISASSEMBLE, CRUSH, PUNCTURE, SHORT EXTERNAL CONTACTS, EXPOSE TO TEMPERATURE ABOVE 60 C (140°F), OR DISPOSE OF IN FIRE OR WATER. REPLACE ONLY WITH SPECIFIED BATTERIES. THE SYMBOL INDICATING ‘SEPARATE COLLECTION’ FOR ALL BATTERIES AND ACCUMULATORS SHALL BE THE CROSSED- OUT WHEELED BIN SHOWN BELOW IN CASE OF BATTERIES, ACCUMULATORS AND BUTTON CELLS CONTAINING MORE THAN 0.0005% MERCURY, MORE THAN 0.0029% CADMIUM OR MORE THAN 0.004% LEAD, SHALL BE MARKED WITH THE CHEMICAL SYMBOL FOR THE METAL CONCERNED: Hg. Cd, OR Pb RESPECTIVELY. PLEASE REFER TO THE BELOW SYMBOL:

FCC Rules

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

•  This device may not cause harmful interference, and
•  this device must accept any interference received, including interference that may cause undesired operation

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>