SKYBELL MOJ-DC500 TrakView Dashcam User Manual
- August 9, 2024
- SKYBELL
Table of Contents
SKYBELL MOJ-DC500 TrakView Dashcam
Product Specifications:
- Power: 5VDC via USB-C port
- Cellular Connection: Cat4 LTE: Bands 2, 4, 12, 17, 66, 71 (carrier dependent)
- Imaging: Front Camera: Color, 1937 x 1097, 2.1MP; Interior Camera: Color, 1920 x 1080, 2.1 MP
- Video: Front Camera Video: 480p/720p/1080p H.264 @30fps; Interior Camera Video: 480p/720p H.264 @30fps
- Mounting: Suction cup attachment to windshield
- Mobile Application: Mojio Force; Supports Android 8.1 or iOS 9.0 or later
- LED Indicator: Front panel, back-lit RGB. Colors are user-selectable.
- Audio: Speaker: Built-in, 1 watt; Microphone: Omni-directional, -42 +/- 3 dB
Product Usage Instructions
Installation and Set Up:
- If you don’t have the Force by Mojio App, scan the QR code below to install it on your smartphone (iOS or Android).
- Sign into your account and follow the prompts to activate your dashcam and complete the setup.
- Plug one end of the supplied USB-C cable into the dashcam. Plugthe other end of the USB-C cable into the OBD-II dongle.
- With the engine OFF, plug the OBD-II dongle into the vehicle’s ODB-II port.
- Turn the engine ON to activate the dashcam and cellular connection. A live video stream should be viewable in the phone App.
- The TrakView Dashcam mounts to the front windshield. Select a location near the rear-view mirror that will not interfere with the mirror nor block the driver’s view of the roadway.
- Press and hold the tilt adjustment button to achieve the proper up/down angle for the dashcam.
- Clean the windshield surface with alcohol and allow the surface to fully dry. Release the suction cup lock and push the suction cup against the clean windshield area.
- When satisfied with the dashcam’s positioning, lock the suction mount.
- Use the provided cable tuck tool to hide the USB-C cable under the vehicle’s window trim.
Note: Always pay careful attention to the road while driving. Do not drive distracted. Refer to your vehicle’s warning and indicator lights for the most current diagnostic information. Always consult the owner’s manual for maintenance guidelines.
FAQ
- Q: What do I do if I face issues with the LTE connection?
- A: If you are facing issues with the LTE connection, try restarting both the dashcam and your smartphone. Ensure that you are in an area with good cellular network coverage.
- Q: Can I use the dashcam without connecting it to the OBD-II port?
- A: No, the dashcam needs to be connected to the vehicle’s OBD-II port for power and activation.
Product Overview
The TrakView dashcam is an all-in-one, OBD-II powered Dashcam that features 4G LTE connectivity, GPS, dual-facing HD cameras, up to 256 GB of storage, and with vehicle diagnostics plus built-in ADAS capabilities. The TrakView Dashcam delivers high-value use cases for both consumers and fleets, with access to real-time location tracking data, video monitoring services, and vehicle health insights. The TrakView Dashcam is designed to mount to the vehicle’s front windshield. Power is provided to the Dashcam via the OBD-II port. In the case when the ignition is OFF, the Dashcam is powered by its internal battery. The camera has two 2MP camera sensors to provide a forward-facing view of traffic and a rear-facing view of the driver and passenger compartment. Video images, location data, and vehicle performance information are sent to the Cloud via a 4G modem. This information can be monitored and viewed using the Mojio Force mobile application (iOS and Android). Recording can be initiated by pushing the REC button on the rear or remotely via the App. The rear LED indicators display the product’s current operating status and error conditions.
Technical Specifications
- Power
- 5VDC via USB-C port
- Cellular Connection
- Cat4 LTE: Bands 2, 4, 12, 17, 66, 71 (carrier dependent)
- Imaging
- Front Camera: Color, 1937 x 1097, 2.1MP
- Interior Camera: Color, 1920 x 1080, 2.1 MP
- Video
- Front Camera Video: 480p/720p/1080p H.264 @30fps, H.264
- Interior Camera Video: 480p/720p H.264 @30fps, H.264
- Mounting
- Suction cup attachment to windshield
- Mobile Application
- Mojio Force; Supports Android 8.1 or iOS 9.0 or later
- LED Indicator
- Front panel, back-lit RGB. Colors are user-selectable.
- Audio
- Speaker: Built-in, 1 watt
- Microphone: Omni-directional, -42 +/- 3 dB
- Memory
- Micro SD Card, 64 GB to 256 Gb
- Front LED Indicator
- REC – red
- Rear LED Indicators
- REC – red
- PWR – red/amber
- LTE – red/green
- Finish/Color
- Matte and high gloss black
- Dimensions
- h: 6.2in/157mm, w: 3.9in/99mm, d: 2.1in/53mm Weight: 8.5oz/240g
- Environment
- 5°C to 50°C / 23°F to 122°F
LED Indicators and Key Features
- When the REC LED is illuminated (solid) red, the dashcam is in normal recording mode.
- When the REC LED is flashing (rapid) red, the SD card is missing or there is an SD card memory error.
- When the REC LED is flashing (moderate) red, the dashcam is in event recording mode.
- When the PWR LED is illuminated (solid) red, the dashcam is ON and powered by the vehicle.
- When the PWR LED is illuminated (solid) amber, the dashcam is running from its internal battery.
- When the PWR LED is flashing (slow) red, the dashcam is in standby mode.
- When the LTE LED is flashing (moderate) green, there is an active connection to the LTE network.
- When the LTE LED is flashing (fast) green, an LTE connection is established.
- When the LTE LED is illuminated (solid) red, there is no connection to the LTE network
Installation and Set Up
- If you don’t have the Force by Mojio App, scan the QR code below to install it on your smartphone (iOS or Android).
- Sign into your account and follow the prompts to activate your dashcam and complete the setup.
- Plug one end of the supplied USB-C cable into the dashcam. Plug the other end of the USB-C cable into the OBD-II dongle.
- With the engine OFF, plug the OBD-II dongle into the vehicle’s ODB-II port.
- Turn the engine ON to activate the dashcam and cellular connection. A live video stream should be viewable in the phone App.
- The TrakView Dashcam mounts to the front windshield. Select a location near the rear-view mirror that will not interfere with the mirror nor block the driver’s view of the roadway.
- Press and hold the tilt adjustment button to achieve the proper up/down angle for the dashcam.
- Certain states or jurisdictions may restrict the placement of the dashcam in certain locations. Please refer to your local Department of Transportation (DOT) website for more details.
- Once a suitable location has been determined, clean the windshield surface with alcohol and allow the surface to fully dry. Release the suction cup lock and push the suction cup against the clean windshield area.
- When satisfied with the dashcam’s positioning, lock the suction mount.
- Use the provided cable tuck tool to hide the USB-C cable under the vehicle’s window trim.
- Always pay careful attention to the road while driving
- Do not drive distracted
- Refer to your vehicle’s warning and indicator lights for the most current diagnostic information
- Always consult the owner’s manual for maintenance guidelines
Need additional help? Scan the QR code below to watch our installation video and access additional resources.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
ISED Statement:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference,including interference that may cause undesired operation of the device.
RF Exposure Statement:
The distance between the user and the Dashcam should be no less than 20 cm.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>