CREALITY K1 Ultra Fast 3D Printer User Manual
- June 10, 2024
- Creality
Table of Contents
K1 Ultra Fast 3D Printer
User Manual
K1 Ultra Fast 3D Printer
Dear Users
Thank you for choosing our products. For the best experience, please read this
User Manual carefully and strictly follow the instructions to operate the
printer. Our teams will always be ready to provide you with the best services.
Please contact us via the phone number or e-mail address provided at the end
of this User Manual when you encounter any problem with the printer. For a
better experience in using our products, you can also leam how to use the
printer in the following ways:Accompanied instructions: you can find the
relevant instructions and videos in the USe flash disk. You can also visit our
official website (https://www.creality.com) to find information regarding
software, hardware, contact information, device instructions, device warranty
information, and more.
NOTES
- Do not use the printer in any way other than described herein in order to avoid personal injury or property damage;
- Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, cool and dustless environment;
- Do not expose the printer to a violent vibration or any other unstable environment, as this may cause pax print quality;
- Please use recommended filaments to avoid clogging of the extrusion head and causing damage to the machine;
- Do not touch the nozzle and the heated bed during operation to avoid bums or personal injury;
- Do not use the power cable of other products during installation. Always use a grounded three-prong power outlet, which accompanies the printer,
- Do not wear gloves or wraps while operating the machine to prevent entrapment of movable parts that could cause crushing and cutting injuries to bodily parts;
- Use the provided tools to clean the filament from the extruder in time taking advantage of the residual temperature after printing. Do not touch the extruder directly when cleaning, otherwise it may cause bums; g Clean the printer frequently.
- Clean the printer body with a dry cloth regularly after powering off the printer, wipe away dust, bonded print filament and foreign objects on the guide rails;
- Children under 10 years old should not use the printer without supervision, otherwise it may cause personal injury;
- Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes; Creality will not be responsible for any violators’ legal liability wider any circumstance;
- Tip: Do not plug in or unplug wires on a charged basis.
About the Device
1.1 About the Printer
1.2
Device Specifications
General Specifications
| Product Model | K1 |
|---|---|
| Dimensions | 355366480mm |
| Machine Weight | 12.5kg |
| Max. Build Dimensions | 220220250mm |
| Print Technology | EOM |
| Rated Voltage | 100-120V-/200-240V-, 50/60Hz |
| Rated Power | 350W |
| Ambient temperature | 10°C-30t / 50°F-86°F |
| Extruder | Sprite Direct Drive |
| Supported Filament | PLA/TPU/PETG/ABS/PET/Carbon |
| Max. Heated Bed Temperature | 100`C |
| Max. Nozzle Temperature | 300°C |
| User Interface | 4.3 inch touch screen |
| Print Interface | USB Flash Disk/LAN Printing/Creality Cloud Printing |
| Power Loss Recovery | Yes |
| Filament Detection | Yes |
| Auto leveling | Yes |
1.3 Packing list
* Tips:
the above accessories are for reference only. Please refer to the physical
accessories!
Unboxing
2.1 Unpacking Steps 
2.2 Install the Product
1 Take the touch screen out of the tool box and connect the touch screen to
the flat cable extended from the base according to Figure A. Then snap the
touch screen into the slot in the baseplate, as shown in Figure B.
Caution:
- Please ensure the correct position for the power supply switch and mains before supply connection, In order to avoid damage to the device.
- If the mains between 100V and 120V, please select the 115V for the power supply switch with a straight screwdriver.
- If the mains between 200V and 240V, please select the 230V for the power supply switch (default Is 230V) with a straight screwdriver.
2 Connection and power on.
****
Caution:
- Do not power up the machine while you are connecting or disconnecting the touch screen.
- The flexible flat cable of the base is pulled lightly and broken carefully.
3 Select a language and click “Next”, then click “OK” on the screen and lift
the heatbed.
4 Take
out the foam as shown and click “OK” to proceed to the next step. Keep the
blue cube in the figure clean of debris and then click “OK”. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>