RYOBI RHWL18 18V ONE+ Hybrid Worklight Instruction Manual
- June 10, 2024
- RYOBI
Table of Contents
RYOBI RHWL18 18V ONE+ Hybrid Worklight
Product Information
The RHWL18 LED Work light is a high-performance, reliable, and safe lighting device designed for general illumination purposes. It is equipped with a powerful LED light source that delivers bright and consistent light output. The product is intended for indoor use only and should not be used in wet or damp conditions.
For safety reasons, the product should only be repaired by an authorized service center. Users are advised not to disassemble the product or attempt to replace the light source. The product should be used only with the recommended battery pack and charger, as using any other battery pack could damage the product, cause a fire or personal injury.
Users are advised to avoid contact with any hot surface and to keep the product away from chemicals, such as brake fluids, gasoline, petroleum-based products, or penetrating oils. These substances can damage, weaken, or destroy the plastic parts of the product and may result in serious personal injury.
The product is lightweight and portable, making it ideal for use in garages, workshops, or outdoor activities. It is also environmentally friendly, and all its components can be recycled or disposed of safely.
Product Usage Instructions
Before using the RHWL18 LED Work light, carefully read the instructions provided in the user manual. Failure to follow these instructions may result in personal injury or damage to the product.
- Charge the battery pack fully before use. Follow the instructions provided with the charger to ensure that the battery pack is charged correctly.
- Attach the battery pack to the product by sliding it into the compartment until it clicks into place.
- To turn on the product, press the power button located on the handle. To turn off the product, press the power button again.
- Do not expose the product to wet or damp conditions, as this could result in a hazardous situation.
- Avoid staring directly at the light source to reduce the risk of eye injury.
- When not in use, store the product and its components in a safe and dry place.
- When the battery pack is low, recharge it using the recommended charger.
- If you encounter any problems with the product, contact an authorized service center for repairs.
- When disposing of the product, its accessories, or packaging, recycle or dispose of them in an environmentally friendly manner.
IMPORTANT!
It is essential that you read the instructions in this manual before
assembling, operating, and maintaining the product.
Subject to technical modifications.
Safety, performance, and dependability have been given top priority in the design of your LED Work light.
INTENDED USE
The LED Work light is intended for general illumination. Do not use the
product in wet conditions.
Do not use the product for any other purpose. Use of the product for
operations different from intended could result in a hazardous situation.
LED WORK LIGHT SAFETY WARNINGS
- The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
- Use only with recommended battery pack and charger. Any attempt to use another battery pack will cause damage to the product and could possibly explode, cause a fire, or personal injury.
- Do not disassemble the product.
- If wrapped or in contact with fabrics, the lens can produce sufficient heat to melt some fabrics. To avoid serious personal injury, never allow the lens to come in contact with anything.
- Do not place the product or battery pack near fire or heat. This will reduce the risk of explosion and possible injury.
- Remove the battery pack before starting any work on the product.
- Do not store the product in a damp or wet location, or in a location where the temperature may reach or exceed 40°C. For example, inside sheds, vehicles, or metal buildings in the summer.
BATTERY SAFETY WARNINGS
- To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and
regulations.
Follow all special requirements on packaging and labelling when transporting
batteries by a third party. Ensure that no batteries can come in contact with
other batteries or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or tape. Do not
transport batteries that are cracked or leaking. Check with the forwarding
company for further advice.
MAINTENANCE
-
Use only original accessories and spare parts. Should components need to be replaced which have not been described, please contact an authorised service centre.
All repairs should be performed by an authorised service centre. -
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
-
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.
SYMBOLS
Safety
Alert
Volts
Direct current
The rated maximum ambient temperature
Regulatory Compliance Mark (RCM). Product meets applicable regulatory
requirements.
Please read the instructions carefully before starting the product.
Class II product, double insulation
Indoor use only. Do not expose to rain or wet conditions.
Do not stare at light source.
To reduce the risk of injury or damage, avoid contact with any hot surface.
Waste electrical products should not
be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
SYMBOLS IN THIS MANUAL
Note
Parts or accessories sold separately
Overview
Installation
PRODUCT SPECIFICATIONS
- LED Work light
- Model RHWL18
- Voltage 18V
- 100 – 240V
- 50Hz / 60Hz
- Power factor 0.5 – 0.6
- Wattage 14.5 W
- Light output (Lumens)
- High brightness level 1800 Lum
- Medium brightness level 1100 Lum
- Low brightness level 500 Lum
- Colour rendering index (CRI) 80
- Correlated colour temperature (CCT) 5000 K
- Weight – excluding battery pack 0.86 kg
BATTERY
Compatible battery pack (not included)
| RB18L13 | RB18L20A | RB18L50 | RB1820C |
|---|---|---|---|
| RB18L15 | RB18L25 | RB18L50A | RB1840C |
| RB18L15A | RB18L25A | RB18L60A | RB1840X |
| RB18L15B | RB18L40 | RB18L90A | RB1850C |
| RB18L20 | RB18L40A | RB1815C | RB1860X |
Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>