BELLEVUE MVLCF51137BRZ Tymothy 13 Wide Semi Flush Bowl Ceiling Fixture Instruction Manual

BELLEVUE MVLCF51137BRZ Tymothy 13 Wide Semi Flush Bowl Ceiling Fixture

Tools Required (not included): Flathead screwdriver, Phillips screwdriver, Electrica tape, Safety goggles, Ladder.
Bulb Recommended: (1) 60W Type-S medium base vintage-style bulb, Alternate (1)

LED bulb.

Estimated Assembly Time : 20 – 30 minutes

Preparation:

• Identify and inspect all parts before beginning installation
• Check the package contents list and diagrams below to be sure all parts are included.
• If any parts are missing or damaged, do not attempt to assemble, install or operate the fixture.

Warnings And Cautions

• Turn off electricity at the circuit breaker or main fuse box before installation. Consult a licensed electrician i in doubt.
• These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
• Disconnect the fixture from the power source before replacing the bulbs.
• Make sure bulbs are given sufficient time to cool before removal.
• Do not subject glass parts to any shock while in operation or shattering may result.

Package Contents

STEP 1:

• a. Unfold support arms of the fixture assembly to proper locations. (Refer to Arm Orientation)
• b. Remove Mounting Screw from the ring.
• c. Place the ring over the edge of the shade.
• d. Confirm that the holes on the shade align with the holes on the ring. Pass mounting screws through hole of the arm and thread into the ring.
• e. Hand-tighten until snug.

STEP 2:

• a. Secure the crossbar to the outlet box (not included) with outlet box screws.
• b. Tighten until snug.

Note:
The pre-assembled mounting screws on the crossbar should protrude outward.

STEP 3:

• a. Remove mounting balls from the crossbar assembly.
• b. Fit the ceiling canopy to the crossbar assembly and secure it with mounting balls.
• Note: The ceiling canopy should be snug against the ceiling and the mounting balls.
• If not, adjust the length of the mounting screws on the crossbar assembly by unscrewing the preassembled hex nuts.
• Then, screw the mounting screws in or out of the crossbar until the desired length is achieved.
• Once the ceiling canopy is secure, remove the mounting balls and ceiling canopy and proceed to Step 4.

STEP 4:

• a. The lanyard is provided as a means to support the fixture from the junction box while connecting the electrical wires. This enables the fixture to hang from the junction box and your hands are free to make the wire connections.
• b. Turn the button stop so it may be inserted into the crossbar slot. Make sure the button stop is completely inside the crossbar.
• c. Slowly release the fixture to make sure it is supported by the button stop.
• d. Proceed to Step 5. Once wiring is complete, the lanyard will push into the junction box when the Ceiling Canopy is Attached to the ceiling.

STEP 4:

• Use Wire Connectors (supplied) to connect the wires.
  a) Ground Wire:

• 1. Wrap supply ground wire around the green ground screw on the mounting bracket, no less than 2 in. from the end of the wire. Tighten the ground screw.

• 2. Connect fixture green ground wire to supply ground wire with wire connector.

• b) Supply Wire:

• 1. Connect the supply white wire to the white fixture supply wire with a wire connector.

• 2. Connect the supply black (or red) wire to the black fixture supply wire with a wire connector.

• 3. Wrap each connection with approved electrical tape and carefully stuff all of the connected wires into the outlet box.

STEP 5:

• a. Re-attach the ceiling canopy of the fixture body to the crossbar assembly.
• b. Secure with the previously removed mounting balls.

CARE AND MAINTENANCE

Wipe clean using a soft, dry cloth or static duster. Always avoid using harsh chemicals and abrasives to clean fixtures as they may damage the finish.

TROUBLESHOOTING

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>