Klipsch T5 II True Wireless Sport Earphones User Manual

Klipsch T5 II True Wireless Sport Earphones

INSIDE

POWER

• ON
• OFF

PAIRING

OR
HOLD 3 SECONDS (L + R)

CHARGING

OR

WIRELESS CHARGER

FACTORY RESET

HOLD 8 SECONDS

STATUS INDICATORS

• Solid Red →Charging

• Blink Red x 1 → Low Battery

• Slow Blink Blue →Ready to Pair

• Fast Blink Blue →Connected

• LED 1 →Charging 0-33%

• LED 2 →Charging 33-66%

• LED 3 →Charging 66-100%

• Solid Red

• Blink Red x 1

• Slow Blink Blue

• Fast Blink Blue

• LED

• Charging

• Low Battery

• Ready to Pair

• Connected

CONTROLS

Transparency On/Off

Voice Assistant

DURING PLAYBACK

CALL HANDLING

SINGLE CONTROLS

Voice Assistant

Power Off

Transparency On/Off

MODE

• Short Press

• Long Press

• Double Press

• During Playback

• Voice Assistant

• Call Handling

• During Call

• POWER OFF

TRUE WIRELESS RESET

BLINKING RED

PURPLE

MOISTURE REMOVAL SYSTEM

The desiccant pod at the top of the case is filled with moisture absorbing crystals. These crystals are made from silica gel and periodically need to be reactivated.

REACTIVATING MOISTURE DESICCANT

TO REACTIVATE:
Microwave oven:

1. Remove pod from the charging case.
2. Place pod in microwave, holes up, and heat for 30 seconds on high. Let cool to the touch.
3. Replace pod into the charging case.

WARNING: Never heat desiccant for longer than two (2) minutes total. Let cool before handling.
NOTE: After several cycles, the crystals lose their ability to absorb moisture. Replacement desiccant pods are available from Klipsch.

PLACEMENT

INSTALLING EAR WING

TROUBLESHOOTING

TOPIC: There is sound coming from one side only.
SOLUTION: Insert the other earphone into the case and take it out again. If this fails, follow “True Wireless Reset” procedure on Page 8.

TOPIC: My audio and video won’t sync up.
SOLUTION: Some apps do not always use the correct audio codec for lowest latency. If the audio is delayed in an App, try streaming the same video using your device’s web browser.

TOPIC: How do I get the best Bluetooth connection?
SOLUTION: Ensure your device isn’t being blocked by your body or any objects (move it from your pocket). Next, place the earphones back in the case and take out the earphone that corresponds with the side your device is on first (Right ear-phone if right pocket, left earphone if left pocket). Try to reduce the distance between your earbuds and your audio device to further improve performance.

TOPIC: Are my earphones water and dust resistant?
SOLUTION: Your earphones are IP67 water and dust proof which means they can handle rain, mud, and other adventures. Saltwater and corrosive chemicals will damage the earphones and should be washed off with fresh water immediately.

TOPIC: What if I have poor wireless connectivity?
SOLUTION: If possible, move away from cell phone towers, dense WIFI networks, other Blue-tooth devices and household appliances like microwave ovens.

ADDITIONAL SUPPORT:
Be sure to check klipsch.com/support and down-load Klipsch Connect to install the latest firmware available.

TOPIC: I want more bass.
SOLUTION: Try a larger ear tip, further boost bass using the Klipsch Connect App.

TOPIC: I can’t connect to my phone.
SOLUTION: Factory reset the earphones by holding the button on both left and right for 8 seconds. They will flash red/blue/red/blue and turn off. Next, press both earphones simultaneously for 1 second to power them on,

SPECIFICATIONS:
Bluetooth 5.1
A2DP Codecs: SBC, aptX®, AAC
Range: up to 10m (33 ft.)
Charging Case Input Rating: 5V DC, 0.5A

©2020, Klipsch Group, Inc. is a wholly-owned subsidiary of Voxx International Corporation. Klipsch and Keepers of the Sound are trademarks of Klipsch Group Inc., registered in the U.S. and other countries. Product of China.

FCC Caution.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

IC Warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>